Digital Commons Network^™

Coordinated Unmanned Aircraft System (Uas) And Ground-Based Weather Measurements To Predict Lagrangian Coherent Structures (Lcss), Peter J. Nolan, James Pinto, Javier González-Rocha, Anders Jensen, Christina N. Vezzi, Sean C. C. Bailey, Gijs De Boer, Constantin Diehl, Roger Laurence Iii, Craig W. Powers, Hosein Foroutan, Shane D. Ross, David G. Schmale Iii

Mechanical Engineering Faculty Publications

Concentrations of airborne chemical and biological agents from a hazardous release are not spread uniformly. Instead, there are regions of higher concentration, in part due to local atmospheric flow conditions which can attract agents. We equipped a ground station and two rotary-wing unmanned aircraft systems (UASs) with ultrasonic anemometers. Flights reported here were conducted 10 to 15 m above ground level (AGL) at the Leach Airfield in the San Luis Valley, Colorado as part of the Lower Atmospheric Process Studies at Elevation—a Remotely-Piloted Aircraft Team Experiment (LAPSE-RATE) campaign in 2018. The ultrasonic anemometers were used to collect simultaneous measurements of …

A Novel Splitting Beam Laser Extensometer Technique For Kolsky Tension Bar Systems, Colin Loeffler

Mechanical Engineering Research Theses and Dissertations

The Kolsky (Split Hopkinson) Bar has become a well-known and established experimental technique for characterizing the mechanical behavior of materials subjected to dynamic loading conditions. Kolsky bar based experimental techniques facilitate the application of controlled and repeatable dynamic loading conditions to a specimen as well as the high resolution measurement of the resulting mechanical response. In recent decades the technique has been refined and adapted to provide more complex dynamic stress-states beyond uniaxial compression. However, the increasing complexity of the experimental apparatus introduces uncertainty to the traditional specimen deformation measurement techniques.

In this thesis, a direct non-contact optical measurement technique …

Optical Micro-Seismometer Based On Evanescent Field Perturbation Of Whispering Gallery Modes, Jaime Da Silva

Mechanical Engineering Research Theses and Dissertations

This thesis proposes a light-weight, compact, and accurate optical micro-seismometer that could be used in many applications, such as planetary exploration. The sensor proposed here is based on the principle of whispering gallery optical mode (WGM) resonance shifts of a dielectric micro-resonator due to disturbances of its evanescent field. The micro-seismometer could be used in place of the traditional bulky seismometers. The design of a waveguide-resonator and mechanical structure to disturb the evanescent field are presented. A proof-of-concept a seismometer model that uses a 5µm ring resonator is numerically tested with actual seismic data. The results show that a WGM-based …

Non-Classical Plate Models Incorporating Microstructure And Surface Energy Effects: Their Variational Formulations And Applications, Gongye Zhang

Mechanical Engineering Research Theses and Dissertations

In this dissertation research, new non-classical models for Kirchhoff and Mindlin plates are developed and applied to study band gaps for flexural wave propagation in composite plate structures.

In Chapter 2, a new non-classical model for a Kirchhoff plate resting on an elastic foundation is developed using a modified couple stress theory, a surface elasticity theory and a two-parameter elastic foundation model. A variational formulation based on Hamilton’s principle is employed, which leads to the simultaneous determination of the equations of motion and the complete boundary conditions and provides a unified treatment of the microstructure, surface energy and foundation effects. …

A Fuzzy Based Model For Standardized Sustainability Assessment Of Photovoltaic Cells, Muath Bani Salim, Dervis Emre Demirocak, Nael Barakat

Mechanical Engineering Faculty Publications and Presentations

In this paper, a new environmental sustainability indicator (ESI) is proposed to evaluate photovoltaic (PV) cells utilizing Life Cycle Analysis (LCA) principles. The proposed indicator is based on a model that employs a fuzzy logic algorithm to combine multiple factors, usually used in multiple LCAs, and produce results allowing a comprehensive interpretation of LCA phase sub-results leading to standardized comparisons of various PV cells. Such comparisons would be essential for policymakers and PV cell manufacturers and users, as they allow for fair assessment of the environmental sustainability of a particular type of PV with multiple factors. The output of the …

Optimal Placement Of Distributed Energy Storage Systems In Distribution Networks Using Artificial Bee Colony Algorithm, Choton K. Das, Octavian Bass, Ganesh Kothapalli, Thair S. Mahmoud, Daryoush Habibi

Research outputs 2014 to 2021

The deployment of utility-scale energy storage systems (ESSs) can be a significant avenue for improving the performance of distribution networks. An optimally placed ESS can reduce power losses and line loading, mitigate peak network demand, improve voltage profile, and in some cases contribute to the network fault level diagnosis. This paper proposes a strategy for optimal placement of distributed ESSs in distribution networks to minimize voltage deviation, line loading, and power losses. The optimal placement of distributed ESSs is investigated in a medium voltage IEEE-33 bus distribution system, which is influenced by a high penetration of renewable (solar and wind) …

Fluid Structure Interaction Study Of The Obstructive Sleep Apnea And Surgical Treatment Using Suture-Patch Device On The Patient’S Tongue, Yang Liu

UNLV Theses, Dissertations, Professional Papers, and Capstones

Up to 14% of the U.S. population is estimated to have obstructive sleep apnea (OSA) related to obesity, and there is increased incidence occurring worldwide. While treatment with continuous positive airway pressure (CPAP) resolves airway obstruction, patient compliance is relatively low. Alternative interventions are available to treat OSA patients; however, their outcomes have had variable results. For example, current technologies have demonstrated an inability to define and treat the specific anatomical site(s) causing the obstruction, resulting in suboptimal modifications of the airway and poor control of OSA.

In the current study, a three-dimensional (3-D) fluid-structure interaction (FSI) numerical simulation has …

Design And Preliminary Evaluation Of A Supercritical Carbon Dioxide Brayton Cycle For Solar Dish Concentrator Clean Energy Production, Danielle Nobles-Lookingbill

UNLV Theses, Dissertations, Professional Papers, and Capstones

As we move toward energy independence and more ambitious clean energy goals, solar energy research must push the efficiency limits of traditional energy generation systems. Increases in efficiency can be achieved by increasing the hot temperature of the power cycle. Recent research demonstrates the potential for increased efficiency and a vastly smaller component size when supercritical carbon dioxide Brayton power cycles are used. Concentrated solar and nuclear heat sources are capable of achieving the high working fluid temperatures needed for significant efficiency gains. This NSF EPSCoR funded, experimental research system is designed to exploit the uniquely immense solar irradiance of …

Biodegradable And Biocompatible Silk Fibroin For Optical Applications, Corey Bryce Malinowski

UNLV Theses, Dissertations, Professional Papers, and Capstones

This study presents nanopatterned silk fibroin films that were fabricated using soft lithography and nanoimprinting to replicate patterns from diffraction gratings. These film’s optics were analyzed based on their light scattering potential as well as their transmittance and transmission haze using a laser light, spectrometer, and UV-Vis spectrophotometer, respectively. The patterned fibroin films all displayed similar light scattering patterns to their master patterns with some transmission haze. When using the spectrometer to measure samples, those made without any nanostructure displayed transmission of 90% and over, while those with patterns depended on the structure used. The denser a structure, like the …

Stability Of A Spinning Triangle Tethered Spacecraft System In A Circular Orbit, Matthew James Heitstuman

Mechanical Engineering ETDs

Equations of motion are derived for a spinning triangle tethered spacecraft system and are used to analyze the stability of such systems. Floquet theory is applied to the linearized, periodic coefficient, equations of motion to analyze spin stability as a function of triangle geometry and the average spin rate of the satellite relative to the angular velocity of the spacecraft orbiting around a central body. The results of the Floquet analysis show that spin stability is achievable for many combinations of spacecraft geometry and spin rate. Spacecraft engineers or operators for a triangle-shaped tethered spacecraft can use this information for …

Cfd Modeling Of Smoke Movement In An Atrium, Robin Wu

UNLV Theses, Dissertations, Professional Papers, and Capstones

The purpose of this paper is to better understand the behavior of smoke movement in an atrium. Thus gives first responders and civilians in and out of building a better understanding

With the advancements of modern technology, computers and softwares make simulation models possible such as fire models to simulate fire and smoke movements. In this paper, a computational fluid dynamic (CFD) software Fire Dynamic Simulator (FDS) is used to conduct a series of atrium tests to investigate the effectiveness of smoke exhaust systems. FDS solves the Navier-Stokes equations appropriate for low speed flows (Ma < 0.3) with an emphasis on smoke, heat transport and CO2 concentrations from fires. The default turbulence model used in FDS simulation is the Large Eddy Simulation (LES), which is the solution of Navier-Stokes equations at low speed.

The compartment tested was 9 …

Integration Of A Commercial Smart Thermostat To The Aggregated Load Control Simulation Framework, Jee Won Choi

Mechanical Engineering ETDs

As part of an effort to achieve a better balance between the power demand and supply, load (demand) control simulation framework is previously developed. In the framework, HVAC load is used as a control resource, driven by the thermostat logic modeled within the framework. However, it has not been proved, whether a com- mercial thermostat is able to perform modeled thermostat’s features. Therefore, it is desired to integrate a commercial thermostat to the framework, to verify its capabil- ity of participating and performing the Demand Response (DR) scheme developed. A ‘Nest Learning Thermostat’ is selected as a commercial thermostat. Nest …

Virtual Reality Simulation Of Glenoid Reaming Procedure, Mohammadreza Faieghi

Electronic Thesis and Dissertation Repository

Glenoid reaming is a bone machining operation in Total Shoulder Arthroplasty (TSA) in which the glenoid bone is resurfaced to make intimate contact with implant undersurface. While this step is crucial for the longevity of TSA, many surgeons find it technically challenging. With the recent advances in Virtual Reality (VR) simulations, it has become possible to realistically replicate complicated operations without any need for patients or cadavers, and at the same time, provide quantitative feedback to improve surgeons' psycho-motor skills. In light of these advantages, the current thesis intends to develop tools and methods required for construction of a VR …

Electroactive Artificial Muscles Based On Functionally Antagonistic Core–Shell Polymer Electrolyte Derived From Ps-B-Pss Block Copolymer, Van Hiep Nguyen, Jaehwan Kim, Rassoul Tabassian, Moumita Kotal, Kiwoo Jun, Jung-Hwan Oh, Ji-Myeong Son, Muhammad Taha Manzoor, Kwang Jin Kim, Il-Kwon Oh

Mechanical Engineering Faculty Research

Electroactive ionic soft actuators, a type of artificial muscles containing a polymer electrolyte membrane sandwiched between two electrodes, have been intensively investigated owing to their potential applications to bioinspired soft robotics, wearable electronics, and active biomedical devices. However, the design and synthesis of an efficient polymer electrolyte suitable for ion migration have been major challenges in developing high-performance ionic soft actuators. Herein, a highly bendable ionic soft actuator based on an unprecedented block copolymer is reported, i.e., polystyrene-b-poly(1-ethyl-3-methylimidazolium-4-styrenesulfonate) (PS-b-PSS-EMIm), with a functionally antagonistic core–shell architecture that is specifically designed as an ionic exchangeable polymer electrolyte. The corresponding actuator shows exceptionally …

First Observation Of P-Odd Gamma Asymmetry In Polarized Neutron Capture On Hydrogen, D. Blyth, J. Fry, N. Fomin, R. Alarcon, L. Alonzi, E. Askanazi, S. Baeßler, S. Balascuta, L. Barrón-Palos, Alex Barzilov, J. D. Bowman, N. Birge, J. R. Calarco, T. E. Chupp, V. Cianciolo, C. E. Coppola, C. B. Crawford, K. Craycraft, D. Evans, C. Fieseler, E. Frlež, I. Garishvili, M. T. W. Gericke, R. C. Gillis, K. B. Grammer, G. L. Greene, J. Hall, J. Hamblen, C. Hayes, E. B. Iverson, M. L. Kabir

Mechanical Engineering Faculty Research

We report the first observation of the parity-violating gamma-ray asymmetry A(gamma)(np) in neutron-proton capture using polarized cold neutrons incident on a liquid parahydrogen target at the Spallation Neutron Source at Oak Ridge National Laboratory. A(gamma)(np) isolates the Delta I = 1, S-3(1)-> P-3(1) component of the weak nucleon-nucleon interaction, which is dominated by pion exchange and can be directly related to a single coupling constant in either the DDH meson exchange model or pionless effective field theory… See full text for full abstract.

Mechanical Engineering News, Georgia Southern University

Mechanical Engineering News (2013-2023)

• Governor Breaks Ground on New Engineering and Research Building

Assessment Of Cooling And Heat Transfer Properties Of Quenchants With Matlab, Lemmy Meekisho, Rosa L. Simencio Otero, Jônatas M. Viscaino, D. Scott Mackenzie, George Totten, Lauralice C.F. Canale

Mechanical and Materials Engineering Faculty Publications and Presentations

There is ongoing interest for evaluating the potential of renewable base stocks, such as vegetable oils, to replace petroleum oils as metal quenchants. Perhaps the most critical part of this process is characterizing and comparing the cooling and heat transfer performance of potential quenchant candidates. In this work, cooling curves of two vegetable oils, palm oil and canola oil, were obtained along with a commercially available conventional and an accelerated petroleum quenchant using the so-called Tensi multiple thermocouple probe, with emphasis on the center probe emulating a small probe concept. The lumped-parameter approach was implemented in the MATLAB environment (Mathworks …

Concentric Contra-Rotating Dual Shaft Vertical Axis Wind Turbine, Emily Walz, Marcellin Zahui, Andrew Shires, Carl Gilkeson

Essential Studies UNDergraduate Showcase

A typical vertical axis wind turbine (VAWT) consists of two or more airfoils all attached to a single central axis. The wind turbine style most commonly found in renewable energy is the horizontal axis wind turbine (HAWT) that have a high energy production efficiency in exchange for requiring large amounts of land and air space. Alternatively, a VAWT can function in low speeds and in smaller less typical locations. As a result, novel VAWT designs are researched to improve their energy efficiency. An example of a novel VAWT is the concentric counter-rotating VAWT investigated theoretically using the 2D computational fluid …

College Of Engineering Senior Design Competition Fall 2018, University Of Nevada, Las Vegas

Fred and Harriet Cox Senior Design Competition Projects

Part of every UNLV engineering student’s academic experience, the senior design project stimulates engineering innovation and entrepreneurship. Each student in their senior year chooses, plans, designs, and prototypes a product in this required element of the curriculum. A capstone to the student’s educational career, the senior design project encourages the student to use everything learned in the engineering program to create a practical, real world solution to an engineering challenge. The senior design competition helps focus the senior students in increasing the quality and potential for commercial application for their design projects. Judges from local industry evaluate the projects on …

Quenchant Cooling Curves, Rewetting, And Surface Heat Flux Properties Of Vegetable Oils, Rosa L. Simencio Otero, Jônatas M. Viscaino, Jun Xu, Jianfeng Wu, George Totten, Lauralice C.F. Canale

Mechanical and Materials Engineering Faculty Publications and Presentations

Vegetable oils are currently used for biodegradable and renewable base stocks for quenchant formulation. However, there are relatively few references relating to their true equivalency, or lack thereof, comparative to the quenching performance of petroleum oil-based quenchant formulations. To obtain an overview of the variability vegetable oil quenching performance, the cooling curves and rewetting properties were determined, and the surface heat flux properties were calculated. The vegetable oils that were studied included canola, coconut, corn, cottonseed, palm, peanut, soybean, and sunflower oils. Cooling curves were obtained using the Tensi multiple-surface thermocouple 15 mm diameter by 45 mm cylindrical Inconel 600 …

Automated Compilation Test System For Embedded System, Mohamad Khairi Ishak, Ooi Jun Hwan, Teh Jiashen, Nor Ashidi Mat Isa

Makara Journal of Technology

Embedded system testing involves testing an integration of software and hardware. It is increasingly difficult to evaluate the functionality of each module within a short time because of the increasing number of tests required. In this paper, a novel stepwise methodology involving the use of an automated compilation test system (ACTS) is proposed, to improve the quality of testing and optimize the testing time using automation. Using the proposed method, the testing coverage can be maximized, while minimizing the manual work and testing time required. This ACTS was used to automate the test code compilation and execution for different hardware …

Transition Metal Dichalcogenide For High-Performance Electrode Of Supercapacitor, Saifful Kamaluddin Muzakir, Ahmad Salihin Samsudin, Bouchta Sahraoui

Makara Journal of Technology

Molybdenum dichalcogenides have been reviewed from the perspectives of bandgap, conductivity, and oxidation states of transition metal. Researchers have concluded that a narrow-bandgap transition metal dichalcogenide with high conductivity could be achieved for the high-performance electrode of a supercapacitor.

Ascorbic Acid Degradation In Cut Lemon Packaged Using Oxygen Scavenging Active Film During Storage, Kurniawan Yuniarto, Setyo Purwanto, Bruce Ari Welt, Anang Lastriyanto

Makara Journal of Technology

Oxygen scavenging active film can be used to prevent diffusion of free oxygen due to the action of permeation mechanism. In this study, biodegradable oxygen scavenging plastic film was designed by incorporating an antioxidant agent into plasticized polylactic acid or PLA-PEG (PPLA). Butylated hydroxytoluene (BHT) was added at different concentrations into the matrix of the PPLA film using a direct casting method to produce oxygen scavenging active film. The antiradical activity of the oxygen scavenging active film was observed, which could be applied for preventing vitamin C degradation in cut lemon during storage. The antiradical activity of the active film …

A 2.3/3.3-Ghz Dual Band Low Noise Amplifier Using Switchable Load Inductor In 0.18-Um Cmos Technology, Taufiq Alif Kurniawan, Hsiao-Chin Chen

Makara Journal of Technology

In this paper, the dual band low noise amplifier is designed in 0.18-μm CMOS technology. By combining the proposed switchable load inductor for gain controlling and the conventional inductive source degeneration topology, narrow band gain and good impedance matching are achieved at 2.3/3.3-GHz frequency bands. The new mathematical analysis of low noise amplifier design is derived to define the component parameters of the proposed circuits. The proposed low noise amplifier exhibits gain of 17.18 dB and 15.5 dB, and noise figure of 2.67 dB and 2.52 dB at the two frequency bands, respectively.

Conversion Of Heat Energy From Cooling Water Of Diesel Engine To Electrical Energy Using Thermoelectric Generator, Muhammad Hasan Albana

Makara Journal of Technology

This research objective is to convert heat from the radiator fluid of a diesel engine to electrical energy by utilizing a thermoelectric generator (TEG). The TEG consists of 20 semiconductors (TE modules) and is equipped with a heat sink. The research shows that using the TEG, the heat of radiator fluid can be converted to electrical energy, although the electricity generated is small. The maximum electrical voltage generated by the TEG when modules were connected in series was 10 volts. When the TE modules were connected in parallel and series-parallel, the maximum voltages generated were 2.11 and 2.53 volts, respectively. …

The Importance Of Usability Aspect In M-Commerce Application For Satisfaction And Continuance Intention, Yassierli Yassierli, Vinsensius Vinsensius, M. S. Syed Mohamed

Makara Journal of Technology

There has been a rapid growing of m-commerce application in recent years due to the development of mobile communication technology and e-commerce business. However, only about 30% of online users, who conduct online searching, make online purchases. The low conversion rate seems to be correlated with poor usability aspect of most m-commerce applications and poor satisfaction reported by users. Research has reported that satisfaction and continuance intention in using m-commerce applications have relationships with service quality and information quality. In this study, a new model of user satisfaction and continuance intention in the context of mobile application was proposed by …

Activated Carbon Fixed-Bed Adsorber Design For Treating Chromium Hexavalent Wastewater, Tedi Hudaya, Velicia Rachmat

Makara Journal of Technology

Pollution caused by industrial wastewater containing heavy metals is a major issue, primarily due to its toxic nature. A cheap yet effective method to deal with such wastewater is activated carbon adsorption. The purpose of this research is to evaluate and design a fixed bed adsorber with granular activated carbon as an adsorbent to process wastewater-containing chromium hexavalent (Cr 6+). Experiments show that the Langmuir isotherm fits the equilibrium data as effectively as the Freundlich isotherm. Activated carbon used in this research is Jacobi 2000® derived from bituminous coal. The lab scale inlet volumetric flow is 100 mL/h with different …

Immittance Response On Carboxymethyl Cellulose Blend With Polyvinyl Alcohol- Doped Ammonium Bromide-Based Biopolymer Electrolyte, Norfatihah Mazuki, Yuki Nagao, Ahmad Salihin Samsudin

Makara Journal of Technology

The blended carboxymethyl cellulose (CMC) and polyvinyl alcohol (PVA) doped with various compositions of ammonium bromide (NH4Br)-based solid biopolymer electrolytes (SBEs) were prepared by using the casting method. In this present work, CMC/PVA–NH4Br SBE thin film was used to investigate the electrical conductivity via electrical impedance spectroscopy. The maximum conductivity obtained was 3.21 X 10−4 S cm−1 for sample AB20 at ambient temperature (303 K), and this result might be due to the increased number of charge carrier. A dielectric study was conducted to understand the conductivity behavior. The electrical properties have been measured as a function of frequency of …

Portable Thermoelectric Refrigerator, Cassandra Danielle Beck, Ryan Theodore Gelinas, Joshua Michael Dimaggio, Zachary David Wilson

Mechanical Engineering

This project created a versatile thermoelectric refrigerator that can be used via a wall outlet. The product is durable and effective. The refrigerator is functional in any ambient temperature, and uses thermoelectric cooling, and work from a standard 120V power outlet. By understanding existing products’ limitations and strengths, this project produced a product that outperforms what’s currently on the market. Many of the existing products’ operating temperature is dependent on the ambient temperature of the surroundings, which is a large drawback. Additionally, most of them take a long time to reach their lowest temperature, around 3 hours. One team member, …

Towards Environmentally Sustainable And Cost-Effective Food Distribution In The U.S., Jasmina Burek

Graduate Theses and Dissertations

Distribution centers (DCs) and supermarkets have an important role in food sustainability, but no previous research has accounted for their environmental impact. The purpose of this research was to assess environmental sustainability of grocery, perishables, and general merchandise DCs; to estimate food storing and retailing impact; and to provide cost-effective strategies to reduce DCs’ environmental impacts. The importance and relevance of the research is threefold: improving sustainability of DCs, food storing, and food retailing. The main method used in this research was the life cycle assessment (LCA) method. An initial study calculated environmental impacts of the Wal-Mart Stores, Inc. DCs, …