Digital Commons Network^™

Test 1909: Case-Ih Steiger 430 And 435 Diesel 16-Speed Also Case-Ih Stx 430 Diesel 16-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA

The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data.

EXPLANATION OF THE TEST PROCEDURES

Purpose

The purpose of …

Granular Contact Lubrication: Theory And Experiment, Karim El Kholy

LSU Doctoral Dissertations

This dissertation is devoted to a theoretical and experimental study of the granular contact lubrication, both. The theory is based on the kinetic of the granular material where the granules interact with each other and with the boundary surfaces through instantaneous, binary collisions, characterized by a constant coefficient of restitution. Specifically this study focuses on granular lubrication in Couette flows. A series of simulations is reported and the results show good agreement with several published papers. Also, a theory that ties the true temperature to the grain mobility is developed. The true temperature of a granular material depends on the …

Using Building Energy Simulation And Geospatial Modeling Techniques In Determine High Resolution Building Sector Energy Consumption Profiles, Shem C. Heiple

Dissertations and Theses

A technique is presented for estimating hourly and seasonal energy consumption profiles in the building sector at spatial scales down to the individual taxlot or parcel. The method combines annual building energy simulations for cityspecific prototypical buildings and commonly available geospatial data in a Geographical Information System (GIS) framework. Hourly results can be extracted for any day and exported as a raster output at spatial scales as fine as an individual parcel (

Robust Mechanism Synthesis With Random And Interval Variables, Pavan Kumar Venigella

Masters Theses

"Robust mechanism synthesis ensures that the performance of a mechanism is not sensitive to uncertainties in the mechanism and its environment. The uncertainties include the dimension variations, installation errors, random input motion, and various external forces. Robust mechanism synthesis is used to minimize the impact of these uncertainties on the mechanism performance. Robust mechanism synthesis has been performed by either a probabilistic approach or a worst case approach. The former approach describes uncertain parameters as random variables while the latter approach treats uncertain parameters as interval variables. In this work, methods are developed for robustness assessment and robust mechanism synthesis …

Method And System For Far-Field Microscopy To Exceeding Diffraction-Limit Resolution, C. Ya, Hai-Lung Tsai

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The bio-sample (e.g., a live cell) is labeled with a proper number of nanoparticles. Each nanoparticle is pre-co-doped with a controlled ratio of fluorophore donors and acceptors. Two laser pulses are applied to the bio-sample. The first laser pulse has a center wavelength near the peak of absorption spectrum of acceptors. The intensity of first laser pulse is adjusted such that FRET saturation occurs near the center of the focal spot. The focal spot of the first laser pulse is a diffraction-limited Airy disk that has the highest laser intensity in the center of the focal spot. The second laser …

A Two-Layer Composite Model Of The Vocal Fol Lamina Propria For Fundamental Frequency Regulation, Kai Zhang, Thomas Siegmund, Roger W. Chan

School of Mechanical Engineering Faculty Publications

No abstract provided.

Máquina Semiautomática Para Dosificado Y Empaque De Líquidos En Bolsa, Juan Carlos Vizcaino Aponte

Ingeniería en Automatización

Sistema semiautomático de dosificado y empaque en el cual el usuario cuenta con el tubo (bolsa) de empaque y necesita dosificar, empacar, sellar y cortar la dosis necesaria. Alimenta un tanque ubicado en la parte superior de la maquina por medio de bombeo de un tanque mas grande que abastece de material a la maquina. Luego por medio de una jeringa industrial se succiona la cantidad deseada de empaque para luego dosificarla por un tubo que dirige el liquido a la zona de empaque en donde un sistema de selle por medio de mordazas realiza la acción de sellar y …

Neural Network Controller Development And Implementation For Spark Ignition Engines With High Egr Levels, Jonathan B. Vance, Atmika Singh, Brian C. Kaul, Jagannathan Sarangapani, J. A. Drallmeier

Electrical and Computer Engineering Faculty Research & Creative Works

Past research has shown substantial reductions in the oxides of nitrogen (NOx) concentrations by using 10% -25% exhaust gas recirculation (EGR) in spark ignition (SI) engines (see Dudek and Sain, 1989). However, under high EGR levels, the engine exhibits strong cyclic dispersion in heat release which may lead to instability and unsatisfactory performance preventing commercial engines to operate with high EGR levels. A neural network (NN)-based output feedback controller is developed to reduce cyclic variation in the heat release under high levels of EGR even when the engine dynamics are unknown by using fuel as the control input. A separate …

Near Optimal Output-Feedback Control Of Nonlinear Discrete-Time Systems In Nonstrict Feedback Form With Application To Engines, Peter Shih, Brian C. Kaul, Jagannathan Sarangapani, J. A. Drallmeier

Electrical and Computer Engineering Faculty Research & Creative Works

A novel reinforcement-learning based output-adaptive neural network (NN) controller, also referred as the adaptive-critic NN controller, is developed to track a desired trajectory for a class of complex nonlinear discrete-time systems in the presence of bounded and unknown disturbances. The controller includes an observer for estimating states and the outputs, critic, and two action NNs for generating virtual, and actual control inputs. The critic approximates certain strategic utility function and the action NNs are used to minimize both the strategic utility function and their outputs. All NN weights adapt online towards minimization of a performance index, utilizing gradient-descent based rule. …

Modeling And Simulation Of A Microturbine Generator To Be Coupled With A Molten Carbonate Fuel Cell For Distributed Generation, Karleine M. Justice

Browse all Theses and Dissertations

Distributed generation is desired when the individual energy requirements ranging from 25-75 kW of office buildings, restaurants, hospitals and apartments can not be met by the current electric utility grid. Microturbine generators as stand alone power generation systems have been designed to meet these requirements. For power requirements up to 50 MW, hybrid fuel cell systems offer higher efficiency and lower levels of pollutant emissions with more advanced fuel energy savings than non-hybrid systems. The objective of this project is to develop a simulation of a microturbine generator as a stand alone power generation system to validate a microturbine generator …

Phase-Locked Piv Investigation Of The Effects Of The Blowing Ratio Of A Pulsed Vortex Generator Jet In A Low-Pressure Turbine, Nathan Michael Woods

Browse all Theses and Dissertations

At very high altitudes the Reynolds number flow through the low pressure turbine section of the gas turbine engine can drop below 25,000. At these low Reynolds numbers the flow is laminar and extremely susceptible to separation which can lead to increased losses and reduced lift. Small jets of air injected through the suction surface of the airfoil, called Vortex Generator Jets (VGJs), have been shown successful in suppressing separation and maintaining attached flow. Pulsing of these jets has been shown to be as effective as steady jets while reducing the amount of mass flow needed. An experiment using Particle …

Thermal Control Of An Occupied Room: Investigating The Use Of Carbon Dioxide Concentration As An Auxiliary Control Variable, Kevin O'Connell, Aidan O'Dwyer

Conference papers

This paper details the theoretical and experimental work done in the examination of the relationship between human generated carbon dioxide concentration and temperature rise in an occupied room. Generation of carbon dioxide by humans is linked to metabolic rate and heat generation. Therefore, carbon dioxide concentration may be used as an indicator of occupancy in a room. Typically, a heating control system will react slowly to changes in room occupancy if temperature is used as the process variable. The aim of the work was to establish if carbon dioxide concentration in the space could be used as an auxiliary control …

Accelerated Testing Method For Pem Fuel Cell Based Uninterrupted Power Supply Systems, Xinyu Huang, Xiaofeng Wang

Faculty Publications

Proton exchange membrane fuel cell based power systems are on the verge of commercialization for a number of niche applications where batteries are traditionally used. Uninterrupted power supply (UPS) for wireless communication towers and broadband network relay utilities is one of the targeted application of fuel cell power systems with capacity ranging from one to serveral kilowatts. It is believed that fuel cell based UPS systems can offer considerable advantage when extended backup time is desirable. In order to replace the well-known battery based UPS systems, the reliability and perofrmance of fuel cell based UPS system need to be thoroughly …

Lectures In Computational Fluid Dynamics Of Incompressible Flow: Mathematics, Algorithms And Implementations, James M. Mcdonough

Mechanical Engineering Textbook Gallery

From Prologue:

The present lecture notes are written to emphasize the mathematics of the Navier–Stokes (N.–S.) equations of incompressible flow and the algorithms that have been developed over the past 30 years for solving them.

Fracture Toughness Of Ceramic Moulds For Investment Casting With Ice Patterns, Qingbin Liu, Ming-Chuan Leu, Von Richards

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Ice patterns can be used to make ceramic investment moulds for metal castings. Owing to the characteristics of ice, the ceramic mould must be made at subzero temperatures and consequently, requires a different formulation than shells built at room temperature. Success of this process depends greatly on the fracture toughness of mould materials. The present paper describes the experimental results of fracture toughness of mould materials processed from different compositions. The Taguchi method was used to reduce the trial runs. The parameters considered included the ratio of fibre containing fused silica and aluminosilicate powders, the volume of binder and the …

Product Family Design Knowledge Representation, Aggregation, Reuse, And Analysis, Jyotirmaya Nanda, Henri Thevenot, Timothy W. Simpson, Robert B. Stone, Matt R. Bohm, Steven B. Shooter

Mechanical and Aerospace Engineering Faculty Research & Creative Works

A flexible information model for systematic development and deployment of product families during all phases of the product realization process is crucial for product-oriented organizations. In current practice, information captured while designing products in a family is often incomplete, unstructured, and is mostly proprietary in nature, making it difficult to index, search, refine, reuse, distribute, browse, aggregate, and analyze knowledge across heterogeneous organizational information systems. To this end, we propose a flexible knowledge management framework to capture, reorganize, and convert both linguistic and parametric product family design information into a unified network, which is called a networked bill of material …

Acoustic Emission Detection And Prediction Of Fatigue Crack Propagation In Composite Patch Repairs Using Neural Networks, Navdeep Singh, Navrag Singh, Anthony Chukwujekwu Okafor

Mechanical and Aerospace Engineering Faculty Research & Creative Works

An aircraft is subjected to severe structural and aerodynamic loads during its service life. These loads can cause damage or weakening of the structure especially for aging military and civilian aircraft, thereby affecting its load carrying capabilities. Hence composite patch repairs are increasingly used to repair damaged aircraft metallic structures to restore its structural efficiency. This paper presents the results of Acoustic Emission (AE) monitoring of crack propagation in 2024-T3 Clad aluminum panels repaired with adhesively bonded octagonal, single sided boron/epoxy composite patch under tension-tension fatigue loading. Crack propagation gages were used to monitor crack initiation. The identified AE sensor …

Simple Penning Ion Source For Laboratory Research And Development Applications, Joshua L. Rovey, Brandon P. Ruzic, Thomas J. Houlahan

Mechanical and Aerospace Engineering Faculty Research & Creative Works

A simple Penning ion generator (PIG) that can be easily fabricated with simple machining skills and standard laboratory accessories is described. The PIG source uses an iron cathode body, samarium cobalt permanent magnet, stainless steel anode, and iron cathode faceplate to generate a plasma discharge that yields a continuous 1 mA beam of positively charged hydrogen ions at 1 mTorr of pressure. This operating condition requires 5.4 kV and 32.4 W of power. Operation with helium is similar to hydrogen. The ion source is being designed and investigated for use in a sealed-tube neutron generator; however, this ion source is …

Optimal Neuro-Controller Synthesis For Impulse-Driven System, Xiaohua Wang, S. N. Balakrishnan

Mechanical and Aerospace Engineering Faculty Research & Creative Works

This paper presents a new controller design technique for systems driven with impulse inputs. Necessary conditions for optimal impulse control are derived. A neural network structure to solve the resulting equations is presented. The solution concepts are illustrated with a few example problems that exhibit increasing levels of difficulty. Two linear problems-one scalar and one vector-and a benchmark nonlinear problem-Van Der Pol oscillator-are used as case studies. Numerical results show the efficacy of the new solution process for impulse driven systems. Since the theoretical development and the design technique are free from restrictive assumptions, this technique is applicable to many …

Determination Of Laser Absorption Coefficients Of Gas Mixtures Using An Ab Initio Md Model, Zhi Liang, Hai-Lung Tsai, Lan Jiang

Mechanical and Aerospace Engineering Faculty Research & Creative Works

In an Effort to Study the Laser Induced Dissociation of Gas Mixtures for an Ongoing Research Project on Diamond Thin Film Coating using Multiple Lasers, It is Necessary to Determine the Absorption Coefficient of Laser Energy by CO2 Gas. an Ab Initio Molecular Dynamics (AIMD) Model is Used to Determine the Laser Absorption Coefficient of CO2 Gas as a Function of Laser Wavelength and Gas Temperature. the Translational, Rotational, and Vibration Motions of Molecules Are All Taken into Account in Our Model. the Intra-Molecular Potential Energy is Obtained by Solving the Kohn-Sham Equation. the Projector-Augmented Wave (PAW) Exchange-Correlation Potential Function …

Micro Injection Fuel/Air Premixer/Combustion, Jian Zhang

LSU Doctoral Dissertations

Lean premixed (LP) combustion has become the dominant industrial approach to reduce NOx emissions. Homogeneous mixing of lean fuel and air mixtures prevents the presence of undesirable localized regions of near-stoichiometric fuel/air mixtures, thereby allowing a reduction in thermal NOx. A new concept, a multi-point micro injection premixer, is presented in this dissertation. The multi-point micro injection premixer is a porous plate that provides a simple but extremely effective method to mix air and fuel. An array of fuel jets is injected in a direction perpendicular to the plane of the premixer plate into an oncoming counterflow stream of air. …

Modeling And Control Of Freeze-Form Extrusion Fabrication, Xiyue Zhao

Masters Theses

"Freeze-form Extrusion Fabrication (FEF) is an additive manufacturing technique that extrudes ceramic loaded aqueous pastes layer by layer below the paste freezing temperature for component fabrication. As the FEF is aimed at being conducted at low environmental temperatures, down to -20°C, it is necessary to investigate the effect of environmental temperature on the process. The advantages of fabrication at low temperature have been proved by experiments. Comparisons in terms of operation parameters, self-sustaining ability, and system dynamic response were performed at different environmental temperatures ranging from 20°C to -20°C.

It is commonly known in paste extrusion processes that due to …

Thermal Effectiveness Characteristics Of Low Approach Indirect Evaporative Cooling Systems In Buildings, Ben Costelloe, Donal Finn

Articles

Meteorological enthalpy analysis of temperate and maritime climates above latitude 45°N suggests that the water-side evaporative cooling technique has considerable unrealised potential with contemporary “high temperature” building cooling systems—such as chilled ceilings and displacement ventilation. As low approach conditions are the key to exploiting the cooling potential of the ambient air, thermal performance at such conditions needs to be investigated. To address the research issues, an industrial scale test rig, based on a low approach open cooling tower and plate heat exchanger and designed to maximise evaporative cooling potential, has been constructed. The thermal effectiveness of such systems (as a …

Characterization And Modeling Methodology Of Polytetrafluoroethylene Based Reactive Materials For The Development Of Parametric Models, Stephen D. Rosencrantz

Browse all Theses and Dissertations

Certain materials, when impacting a target at high velocity will chemically react due to the shock wave passing through them, thereby increasing the damage done by the material. In particular, the reactive materials of interest are capable of acting as both structure and explosive, allowing them to achieve an effect similar to a High Explosive Incindiary (HEI), without the complexity and added mass of fuses. There are a large number of materials/material combinations that could be used in reactive munitions. The purpose of this effort is to determine an efficient analytical characterization methodology that can be validated with a minimal …

Reactive Multilayer Foils And Their Applications In Joining, Xiaotun Qiu

LSU Master's Theses

In this study, Ni/Al multilayer foils were fabricated by a cold rolling method. A two-stage reaction process was observed in the reaction-ignition experiment. The phase formation process in the cold rolled foils was studied. The first reaction stage with a slow reaction velocity was the lateral growth of Al3Ni phase at isolated nucleation sites and the subsequent coalescence into a continuous layer. The second reaction stage with a fast reaction velocity was the growth of the Al3Ni layers in the direction normal to the Ni/Al interface until all Al was consumed. Afterwards, Al3Ni reacted with the remaining Ni to form …

Development Of Micropump For Microfluidic Applications, Dong Eun Lee

LSU Doctoral Dissertations

This dissertation covers the research work on two types of micropumps, one is based on magnetohydrodynamic (MHD) principle that utilizes Lorentz force for actuation, and the other is based on electrochemical actuation. The AC-type MHD micropump was designed and analyzed as a solution to the bubble formation problem encountered in DC-type MHD micropump. A UV-LIGA process using thick layer of SU-8 negative photoresist was successfully developed to microfabricate the AC MHD micropump. Preliminary studies and tests of the AC MHD micropumps demonstrate that bubble formation was significantly reduced to permit the proper function of the micropump. A continuous flow was …

Eigenvalue Optimization And Its Applications In Buckling And Vibration, Srinivas Gopal Krishna

LSU Doctoral Dissertations

Eigenvalue problems are of immense interest and play a pivotal role not only in many fields of engineering but also in pure and applied mathematics. An in-depth understanding of this class of problems is a pre-requisite for vibration and buckling analyses of structures. Design optimization of structures to prevent failure due to instability (bucking) and vibration introduces the problem of determining optimal physical parameters such that load carrying capacity or the fundamental natural frequency is maximized. A classical example of such problems is the Lagrange problem of determining the shape of the strongest column against buckling. The primary objective of …

Studies On The Heat/Mass Transfer Characteristics And Fluid Structure In A Square Internal Cooling Channel With Dimpled Surfaces, Fuguo Zhou

LSU Master's Theses

Experimental and numerical studies of heat/mass transfer on the dimpled surfaces in square channels are performed. The naphthalene sublimation method is employed in the experimental study. First, in a two-passage rotating channel, circle dimple matrices are cast on the leading and trailing walls in both the inlet and outlet of the serpentine channel. The experiments are carried out with Reynolds number of 7,000 and 21,000, and with Rotation number of 0 and 0.2. The dimpled walls lead to heat/mass transfer enhancements over smooth surfaces both in the stationary case and in the rotating case. In the stationary case, the dimple …

Fabrication Of Perforated Polymer Membranes Using Imprinting Technology, Anish Roychowdhury

LSU Master's Theses

The goal of the present study was to fabricate perforated membrane structures in polymers with the pore diameter ranging from 10 ìm down to the sub ìm scale. The perforated membrane structure plays an important role in many biological systems. Thus the ability to reproduce such architecture will help with the study of biological systems by mimicking biological cell membrane-like structures and open new vistas in the study of transport behavior in cell biology and the separation of biological vesicles. Such structures also have potential uses as components in polymer optics and modular micro/nanofluidic devices. Use of polymer substrates is …

Manufacturing And Characterization Of High-Aspect-Ratio Diffusive Micro-Mixers, Vamsidhar Palaparthy

LSU Master's Theses

In the Ligase Detection Reaction (LDR) technique different chemical reagents of varying concentration are mixed with the by-products of the polymerase chain reaction (PCR) for the detection of low abundant cancer diagnostic markers [1]. An effective micro-mixer which is cheap, durable over a relatively broad range of flows with easy manufacturing is required in this process. This work is aimed at manufacturing mixers according to the required specifications with metrology at every manufacturing process to estimate the limits and tolerances during manufacturing and analyzing their efficiency both numerically and experimentally. An optimum mixer design developed earlier by Maha et.al [2] …