Digital Commons Network^™

Review Of Geopolymer Technology, Barriers And Limitations, Abdullah Kadhim, Bushra Salman Mankhi, Muslim Al-Bujasim

Al-Mustaqbal Journal of Sustainability in Engineering Sciences

Geopolymers are kind of inorganic polymeric green materials, which are considered alternatives to some traditional cementitious materials. Geopolymerisation involves reaction between amount of solid materials rich of high reactive amorphous or semi-amorphous silica and alumina in the existence of alkaline medium (Na₂O or K₂O) to formulate tri-dimensional alumina-silicate polymeric strong network. The present research is targeting to review Geopolymer technology and the major barriers and limitations that impede the implementation and development of Geopolymer technology. The review based on the reports, statistics and the opinions of the construction industry stakeholders, in addition to the past literatures …

Designing A Model For Conservation Agricultural Extension In Western Iran, Mosayeb Gholami, Amirhossien Alibaygi, Abdolhamid Papzan

Al-Mustaqbal Journal of Sustainability in Engineering Sciences

Conservation agriculture is seen as a new solution to environmental degradation and unsusainable water and soil resources. Since the adoption rate for conservation agriculture in Iran is not high, there is a need to design an extension model in this field. The aim of this study was to design an extension model for conservation agriculture in Kermanshah Province, located in the west of Iran. The study involved two groups: experts in conservation agriculture selected via purposeful sampling with a wide range of expertise, and farmers from Ravansar and Sonqor townships in Kermanshah Province, selected through a multistage clustering technique. The …

Crisis Management In Tourism Complexes With Emphasis On Sustainable Development Approach Case Study: Jihad Daneshghahi Tourism Complex In Kermanshah, Iran, Aeizh Azmi

Al-Mustaqbal Journal of Sustainability in Engineering Sciences

Problem statement: Crisis management in tourist complexes can play a crucial role in increasing tourist attraction and mitigating damages resulting from natural hazards. The Jihad University Tourism Complex in Kermanshah is a tourist destination, and this study aims to present a crisis management model for this complex.

Question: What should be the crisis management model for the Jihad University Tourism Complex in Kermanshah?

Objective: This study aimed to propose a crisis management model for the Jihad University Tourism Complex in Kermanshah.

Methods: A questionnaire was used to collect research data. Approximately 50 individuals were selected as the research population and …

Utilizing Collaborating Biomedical Deep Model For Diagnosis Of Ultrasonography Tumor Images, Maytham N. Meqdad, Seifedine Kadry

Al-Mustaqbal Journal of Sustainability in Engineering Sciences

Artificial intelligence models are the most common methods of diagnosing various diseases today. In the meantime, the use of deep learning for faster diagnosis with less error, which is usually less expensive than other methods, is noteworthy. However, these methods are expensive due to the problems of accessing data, including care data such as hospitals and clinics. This article presents a novel federated learning-based approach for ultrasound mammography image classification. In this method, the clients possess their own datasets and are trained to use them. Then, the server, with the help of the trained clients, obtains the best parameters for …

A First Step Towards Understanding Thermomechanical Behavior Of The Nb-Cr System Through Interatomic Potential Development And Molecular Dynamics Simulations, Lucas A. Heaton, Adib J. Samin

Faculty Publications

Utilizing a preliminary interatomic potential, this work represents an initial exploration into the thermomechanical behavior of NbCr solid solutions. Specifically, it examines the effect of different amounts of Cr solute, for which information in the literature is limited. The employed interatomic potential was developed according to the embedded atom model (EAM), and was trained on data derived from density functional theory calculations. While the potential demonstrated reasonable accuracy and predictive power when tested, various results highlight deficiencies and encourage further development and training. Mechanical strength, heat capacities, thermal expansion coefficients, and thermal conductivities were found to decrease with Cr content. …

Shape Memory Alloy Capsule Micropump For Drug Delivery Applications, Youssef Mohamed Kotb

Theses and Dissertations

Implantable drug delivery devices have many benefits over traditional drug administration techniques and have attracted a lot of attention in recent years. By delivering the medication directly to the tissue, they enable the use of larger localized concentrations, enhancing the efficacy of the treatment. Passive-release drug delivery systems, one of the various ways to provide medication, are great inventions. However, they cannot dispense the medication on demand since they are nonprogrammable. Therefore, active actuators are more advantageous in delivery applications. Smart material actuators, however, have greatly increased in popularity for manufacturing wearable and implantable micropumps due to their high energy …

Nickel-Catalyzed Α-Arylation Of Α-Cyanoacetates Enabled By Electrochemistry, Zi-Meng Li, Zhang-Jian Li, Anat Milo, Ping Fang, Tian-Sheng Mei

Journal of Electrochemistry

β-Amino acids have a wide range of applications in the field of pharmaceuticals. Utilizing a combination strategy of nickel catalysis and paired electrolysis, a catalytic α-arylation protocol of carbonyl compounds has been developed. This protocol affords various a-aryl-a-cyanoacetates, which can be reduced to high-value-added α-aryl-β-amino acids. The cross-coupling reaction of electron-deficient aryl bromides with a-cyanoacetates achieves the expected products with good yields and functional group compatibility under mild conditions. Excessive electron-richness in initial aryl bromides facilitates the self-coupling of desired products. DFT calculations confirm that the presence of electron-rich aryl substitutions decreases the …

Comparison Of Ligands In Palladium-Catalyzed Electrochemical Allyl 4-Pyridinylation, Wei-Jie Ding, Chun-Hui Yang, Zhong-Tao Feng, Shi-Rong Lu, Xu Cheng

Journal of Electrochemistry

4-CN-pyridine is a widely applied 4-pyridinylation reagent for diverse transformations. Conventionally, the reaction proceeds via an open-shell radical cross-coupling pathway. Following our previous study, in this work, we report the Pd-catalyzed allyl 4-pyrinylation reaction under electrochemical conditions. The reaction proceeds via radical-polar crossover pathway in which the role of phosphine ligand in reactivity and selectivity was extensively investigated.

A Computational Investigation Of Wood Selection For Acoustic Guitar, Jonah Osterhus

Senior Honors Theses

The acoustic guitar is a stringed instrument, often made of wood, that transduces vibrational energy of steel strings into coupled vibrations of the wood and acoustic pressure waves in the air. Variations in wood selection and instrument geometry have been shown to affect the timbre of the acoustic guitar. Computational methods were utilized to investigate the impact of material properties on acoustic performance. Sitka spruce was deemed the most suitable wood for guitar soundboards due to its acoustic characteristics, strength, and uniform aesthetic. Mahogany was deemed to be the best wood for the back and sides of the guitar body …

Me-Em Enewsbrief, Mar 2024, Department Of Mechanical Engineering-Engineering Mechanics, Michigan Technological University

Department of Mechanical Engineering-Engineering Mechanics eNewsBrief

No abstract provided.

A Multi-Material Platform For Imaging Of Single Cell-Cell Junctions Under Tensile Load Fabricated With Two-Photon Polymerization, Jordan Rosenbohm, Grayson Minnick, Bahareh Tajvidi Safa, Amir M. Esfahani, Xiaowei Jin, Haiwei Zhai, Nickolay V. Lavrik, Ruiguo Yang

Department of Mechanical and Materials Engineering: Faculty Publications

We previously reported a single-cell adhesion micro tensile tester (SCAμTT) fabricated from IP-S photoresin with two-photon polymerization (TPP) for investigating the mechanics of a single cell-cell junction under defined tensile loading. A major limitation of the platform is the autofluorescence of IP-S, the photoresin for TPP fabrication, which significantly increases background signal and makes fluorescent imaging of stretched cells difficult. In this study, we report the design and fabrication of a new SCAμTT platform that mitigates autofluorescence and demonstrate its capability in imaging a single cell pair as its mutual junction is stretched. By employing a two-material design using IP-S …

Can Smart Supply Chain Bring Agility And Resilience For Enhanced Sustainable Business Performance?, Mahak Sharma, Rose Antony, Ashu Sharma, Tugrul Daim

Engineering and Technology Management Faculty Publications and Presentations

Purpose

Supply chains need to be made viable in this volatile and competitive market, which could be possible through digitalization. This study is an attempt to explore the role of Industry 4.0, smart supply chain, supply chain agility and supply chain resilience on sustainable business performance from the lens of natural resource-based view.

Design/methodology/approach

The study tests the proposed model using a covariance-based structural equation modelling and further investigates the ranking of each construct using the artificial neural networks approach in AMOS and SPSS respectively. A total of 234 respondents selected using purposive sampling aided in capturing the industry practices …

New York City’S Rising Sea Level And Coastal Erosion: Approaches To Resiliency, Ryder D. Isidro

Student Theses 2015-Present

No abstract provided.

Improved Ballistic Impact Resistance Of Nanofibrillar Cellulose Films With Discontinuous Fibrous Bouligand Architecture, Colby Caviness

All Theses

Natural protective materials offer unparalleled solutions for impact-resistant material designs that are simultaneously lightweight, strong, and tough. Particularly, the dactyl club of mantis shrimp features chitin nanofibrils organized in a Bouligand structure, which has been shown to effectively dissipate high-impact energy during powerful strikes. The mollusk shells also achieve excellent mechanical strength, toughness, and impact resistance with a staggered, layer-by-layer structure. Previous studies have shown that hybrid designs, by combining different bioinspired microstructures, can lead to enhanced mechanical strength and energy dissipation capabilities. Nevertheless, it remains unknown whether combining Bouligand and staggered structures in nanofibrillar cellulose (NFC) films, forming a …

Blade Design And Validation Of Hydrokinetic Turbine To Harvest Water Current Energy, Setare Sadeqi

University of New Orleans Theses and Dissertations

The innovative aspect of this research lies in the careful integration of cutting-edge technologies throughout the entire process of designing, fabricating, and testing the carbon fiber propeller for the 3-bladed horizontal axis ocean current turbine (OCT). SolidWorks software played a pivotal role in the initial design phase, enabling a meticulous and precise modeling of the propeller's geometry. The utilization of SolidWorks allowed for a detailed exploration of various design parameters, ensuring that the propeller's structure and form were optimized for performance in ocean current conditions. Moving beyond the realm of virtual design, the choice of carbon fiber as the fabrication …

Towing Tank Trials Of Hydrokinetic Turbine Scale Model To Support Marine Energy System Verification, Shahab Rouhi

University of New Orleans Theses and Dissertations

In response to the escalating demand for sustainable energy solutions and the critical reevaluation of conventional fossil fuels due to environmental concerns, this dissertation embarks on a comprehensive exploration of hydrokinetic energy as a promising alternative. The study delves into the underexplored domain of hydrokinetic energy, leveraging innovative methodologies for effective utilization and harnessing, particularly through the development and investigation of hydrokinetic turbines.

In the realm of hydrokinetic energy conversion, our research has exclusively concentrated on horizontal-axis turbines, distinct from other turbine configurations. Noteworthy is the adaptation of a conventional horizontal-axis wind turbine for water currents, revealing enhanced performance through …

Investigation On The Effects Of Biofouling On The Boundary Layer, Adam N. Bacon

University of New Orleans Theses and Dissertations

This study is an investigation of the effect of biofouling on the boundary layer of a flat plate and a NACA 4-digit series foil. Three identical hydrofoils made of resin were placed in the Gulf of Mexico at Grand Isle, Louisiana, and observed and analyzed by marine biologists at the University of New Orleans for their species composition. The resulting biofouling that grew was primarily made up of barnacles and bryozoans. The foils were submerged in an open channel flume at zero incidence and subjected to a series of experiments whose arc-length Reynolds numbers ranged from approximately 13000 to 32000. …

Numerical Simulation Of Laser Induced Elastic Waves In Response To Short And Ultrashort Laser Pulses., Alireza Zarei

All Dissertations

In an era of intensified market competition, the demand for cost-effective, high-quality, high-performance, and reliable products continues to rise. Meeting this demand necessitates the mass production of premium products through the integration of cutting-edge technologies and advanced materials while ensuring their integrity and safety. In this context, Nondestructive Testing (NDT) techniques emerge as indispensable tools for guaranteeing the integrity, reliability, and safety of products across diverse industries.

Various NDT techniques, including ultrasonic testing, computed tomography, thermography, and acoustic emissions, have long served as cornerstones for inspecting materials and structures. Among these, ultrasonic testing stands out as the most prevalent method, …

Effect Of The Microstructure On The Corrosion Behavior Of Alcunimn And Alcunimnsi High Entropy Alloys In A 3.5wt% Nacl Solution, Celine Chiong

Open Access Theses & Dissertations

In this study, the AlCuNiMn and AlCuNiMnSi high entropy alloys (HEAs) are investigated to characterize the effect of Si addition and subsequent annealing treatments on the corrosion behavior in a 3.5wt% NaCl solution at room temperature. The microstructure evolution from the as-received condition and after annealing at 600°C, 800°C, and 1000°C for 24 hours in air is examined. The microstructural transformation of HEAs is extensively reported in the literature. However, its impact on the corrosion resistance of HEAs has not received the same attention. In this study, an increase in the annealing temperature of the base AlCuNiMn alloy improved the …

Analysis Of Additively Manufactured Inconel 718 Combustion Behavior In Promoted Oxygen Environments, Dominic George Dieguez

Open Access Theses & Dissertations

Promoted combustion testing is a vital tool for engineers to establish the combustion and flammability characteristics of materials (metallic or otherwise) in oxygen enriched environments. Historically, much of the established data for metallic promoted combustion has been with regards to materials in their cast and wrought forms. However, with the emergence of additive manufacturing as a preferred method of fabrication, the need exists to evaluate how metals in that form behave. Recent testing has demonstrated that even if a metal or alloy is nominally the same with regards to chemistry, flammability between samples in the wrought form can differ significantly …

Laser Powder Directed Energy Deposition (Lp-Ded) Inconel 718: Laser Power And Heat Treatment Effect On Microstructure And Mechanical Properties, Dana Victoria Godinez

Open Access Theses & Dissertations

This study examines the microstructure and mechanical properties (tensile, hardness, and fatigue endurance) of laser powder-directed energy deposition (LP-DED) printed specimens with varying deposition parameters. Five samples with power inputs ranging from 350 to 2620W, all of similar thicknesses, were evaluated to enable a direct comparison. The varying specimens were heat treated, including stress relief, hot isostatic pressing, solution, and two-step aging. The resulting microstructures and their corresponding hardness values were compared at each heat treatment stage. The fully heat-treated specimens' tensile properties and fatigue life were also examined and compared. Key findings of this study indicate that complete heat …

Earth Abundant Catalyst For Evironmental Sustainability Applications, Javier Hernandez

Open Access Theses & Dissertations

The development of experimental methodologies for synthesizing a diverse range of metallic and metal oxide nanoparticles tailored for sustainable water treatment applications was investigated. These nanoparticles are prepared using environmentally friendly and scalable synthesis methods, underscoring their potential for large-scale production. Synthesized nanoparticles are harnessed for various processes, including catalysis and electrocatalysis, with a primary objective of degrading and removing organic pollutants from water. Key to this research is the encapsulation of nanoparticles within solid supports. Multiple methodologies are explored to engineer supports that ensure nanoparticle stabilization, monodispersion, and prevent unintended release into the environment. Two alternative approaches were evaluated …

Feasibility Study For The Detection Of Damage To Composite Overwrapped Pressure Vessels With Phase Array Ultrasonic Testing, Jordan Scott Hitter

Open Access Theses & Dissertations

When discussing the field of Nondestructive Examination, there are various techniques and instrumentation that can be utilized for analysis of components. However, with newer technology and the development of newer forms of technique, it is critical to explore exactly how these can be applied. This work will aim to explore one newer technique, Phased Array Ultrasonic Testing, and determine the viability of its use for examining Composite Overwrapped Pressure Vessels (COPVs). Currently, the types of vessels have been used in a variety of ways such as in transportation vehicles. More notably, these vessels are used in aerospace applications hence the …

Microstructural Characterization And Oxidation Behavior Of Al-Cu-Ni-Mn And Al-Cu-Ni-Mn-Si Non-Body Centered Cubic High Entropy Alloys, Mckenna Mae Lin Hitter

Open Access Theses & Dissertations

High entropy alloys (HEA) differ from traditional alloying systems because five elements are mixed in equi-atomic proportions, as opposed to having one main principal element. As a result of exploring this new method of alloying, it was found that high entropy alloys demonstrate exceptional mechanical properties, an example being oxidation resistance, and are capable of enduring elevated temperatures. Seeing the potential that this new area of interest contains, studies involving a combination of elements to form various HEA have been performed. Most refractory metals are body-centered cubic and possess extremely high melting temperatures, so they are regularly considered when designing …

Electrochemical Syntheses Of Aryl-Substituted Benzothiophenes And Phenanthrenes Using Benzenediazonium Salts As The Aryl Radical Precursors, Li-Yuan Lan, Yang-Ye Jiang, Raymond Daniel Little, Cheng-Chu Zeng

Journal of Electrochemistry

Aryl-substituted benzothiophene and phenanthrene are important structural units in medicinal chemistry and materials science. Although extensive effort has been devoted to prepare these compounds and a variety of approaches have been developed to construct the 2-substituted benzothiophene core structure, environmental-friendly and efficient synthetic means are still desired. Based on our previous electrochemical Minisci-type arylation reaction with aryl diazonium salt as the aryl precursor, as well as the work from König’s group, herein, we described the use of paired electrolysis to achieve 2-aryl benzothiophenes and 9-aryl phenanthrenes employing benzenediazonium salts as the aryl radical precursors. Initially, 2-methylthiobenzendiazonium salt 1a and 4-methylbenzene …

Electrocatalytic Cyclopropanation Of Active Methylene Compounds, Liang-Hua Jie, Hai-Chao Xu

Journal of Electrochemistry

The development of novel strategies to access cyclopropanes has become increasingly important due to the vital role of these three-membered ring structures in synthetic intermediates, natural products, and pharmaceuticals. Herein, we present an electrocatalytic method for the synthesis of cyclopropanes through intermolecular dehydrogenative annulation of active methylene compounds and arylalkenes. This electrochemical process requires no chemical oxidants, allowing for a speedy access to various functionalized cyclopropanes from inexpensive and readily available materials.

Electrochemical Advanced Treatment Of Desulfurization Wastewater From Coal-Fired Power Plants, Ju-Cai Wei, Juan Yi, Xu Wu

Journal of Electrochemistry

Zero-emission of desulfurization wastewater is one of the main demands for coal-fired power plants. As typical high salinity wastewater, it is hard to purify the desulfurization wastewater from coal-fired power plants through traditional physicochemical treatment or biochemical treatment, e.g., COD and Cl^–. A high concentration of Cl^– ion in desulfurization wastewater restricts wastewater reuse and zero-emission. Electrochemical technology is an attractive method for high salinity wastewater zero-emission, which provides a versatile, efficient, cost-effective, easily automatable, and clean industrial process. For advanced treatment of effluent after triple box process treatment in power plants, this paper reports an electrochemical …

Thermal Performance Investigation Of Thermoelectric Cooling System With Various Hot-Side Cooling Methods, Bowo Y. Prasetyo, Parisya P. Rosulindo, Fujen Wang

Makara Journal of Technology

Thermoelectric devices have been widely used in various applications, including cooling and power generation. The potential application of thermoelectric cooling systems has been studied. However, these systems still face challenges in achieving optimal performance compared with other cooling systems. Several factors, including the hot-side cooling method, influence the performance of thermoelectric systems. This study aimed to investigate the effects of different hot-side cooling methods on the thermoelectric performance and thermal behavior of thermoelectric cooling systems. The testing methods involved the combination of the thermoelectric module with five hot-side heat exchangers, including a square heatsink, a round heatsink, a two-pipe heat …

Injectable And Rapidly Expandable Thrombin-Decorated Cryogels Achieve Rapid Hemostasis And High Survival Rates In A Swine Model Of Lethal Junctional Hemorrhage, Syed Muntazir Andrabi, S.M. Shatil Shahriar, Al-Murtadha Al-Gahmi, Benjamin L. Wilczewski, Mark A. Carlson, Jingwei Xie

Department of Mechanical and Materials Engineering: Faculty Publications

Effective therapies are urgently needed to stabilize patients with marginally compressible junctional hemorrhage long enough to get them to the hospital alive. Herein, we report injectable and rapidly expandable cryogels consisting of polyacrylamide and thrombin (AT cryogels) created by cryo-polymerization for the efficient management of lethal junctional hemorrhage in swine. The produced cryogels have small pore sizes and highly interconnected porous architecture with robust mechanical strength. The cryogels exhibit rapid shape memory properties and prove to be resilient against fatigue. These cryogels also show high water/blood absorption capacity, fast blood clotting effect, and enhanced adhesion of red blood cells and …

A Feasibility Study Of Drilling Fluid Slippage For Wellbore Displacement, John Johnson

LSU Master's Theses

In the ideal plug-flow mode viscoplastic drilling fluids display uniform frontal velocity due to wall slippage (at very low flowrate limited by the fluid’s yield strength). The flow rate could be increased by raising the yield strength that would make the fluid best candidate for frontal displacement. Based on this concept the study qualifies wall slippage effect for wellbore displacement. Using a conceptual model of fluid motion between two parallel plates defines maximum velocity as a function of shearing rate and yield stress. Conversion to coaxial geometry gives practical formulas for fluid testing with rotational viscometer. A new analysis of …