Digital Commons Network^™

Combinatorial Cuni Alloy Thin Film Catalysts For Layer Number Regulation In Cvd Grown Graphene, Sumeer Khanna

Masters Theses

In this work, synthesis of combinatorial library of Cu_xNi_1-x (copper nickel) alloy thin films via co-sputtering from Cu (copper) and Ni (nickel) targets as catalysts for chemical vapor deposition (CVD) growth of graphene is reported. The gradient alloy morphology, composition and microstructure were characterized via scanning electron microscopy (SEM), energy dispersive x-ray spectroscopy (EDS), and x-ray diffraction (XRD), respectively. Subsequently, the Cu_xNi_1-x alloy thin films were used to grow graphene in a CH₄-Ar-H₂ (methane-argon-hydrogen) ambient in thermal CVD tube furnace. The underlying rationale is to adjust the Cu_xNi_{1-x …}

Mass Advection–Diffusion In Creeping Flow Through An Orifice Plate: A Model For Nanoporous Atomically Thin Membranes, Harpreet Atwal, Anika Wong, Michael Boutilier

Chemical and Biochemical Engineering Publications

Continuum transport equations are commonly applied to nanopores in atomically thin membranes for simple modeling. Although these equations do not apply for nanopores approaching the fluid or solute molecule size, they can be reasonably accurate for larger nanopores. Relatively large graphene nanopores have applications in small particle filtration and appear as unwanted defects in large-area membranes. Solute transport rates through these nanopores determine the rejection performance of the membrane. Atomically thin membranes commonly operate in a regime where advection and diffusion both contribute appreciably to transport. Solute mass transfer rates through larger nanopores have previously been modeled by adding continuum …

Atomistic-Continuum Membrane And Machine Learning Models For Two-Dimensional Materials, Upenda Yadav

Dissertations, Master's Theses and Master's Reports

“What could we do with layered structures with just the right layers?” asked Richard Feynman in his famous 1959 lecture, “There’s plenty of room at the bottom.” With the help of the amazing developments of the past several years, we are coming close to answering that question. In 2004, graphene was first isolated from graphite and only six short years later it won the Nobel Prize in Physics. Graphene is one atomic layer of Carbon, it is the thinnest and yet the strongest materials we have ever seen. It is 200 times stronger than its equivalent weight in steel and …

Development Of A Model For Graphene Synthesis In Microwave Plasma-Assisted Reactors, Caleb Prindler

Electronic Theses and Dissertations

Graphene is a novel nanomaterial capable of revolutionizing technology in many sectors but is difficult to produce on a useful scale. To improve our understanding of graphene formation, a computational model has been developed to simulate graphene synthesis in a scalable microwave plasma reactor. Unlike earlier graphene growth models, this one uses a sectional method to solve the population balance model. A sensitivity analysis was performed to assess the impact of the individual process rates. The rates were adjusted by multiplying and dividing the base rates by a factor of 2. The process rates that were adjusted in this way …

Graphene Based Tunable Terahertz Holographic Antennas, Pengfei Ren, Lijun Jiang, Ping Li

Electrical and Computer Engineering Faculty Research & Creative Works

In this work, several representative terahertz (THz) graphene holographic impedance surface antenna are presented. Different to the conventional impedance surface antenna that manipulates the surface impedance via varying the patch size in each unit cell, the surface impedance of the proposed antenna in this paper is readily controlled by applying a tunable DC biasing to each graphene patch cell, the physics behind which is that the conductivity of the graphene is a function of imposed voltage. Thus, the graphene patches of the proposed antenna have same size as well as equal spacing, which makes the modeling process more convenient and …

Electro-Chemo-Mechanics Of The Interfaces In 2d-3d Heterostructure Electrodes, Vidushi Sharma

Dissertations

Unique heterostructure electrodes comprising two-dimensional (2D) materials and bulk three dimensional (3D) high-performance active electrodes are recently synthesized and experimentally tested for their electrochemical performance in metal-ion batteries. Such electrodes exhibit long cycle life while they also retain high-capacity inherent to the active electrode. The role of 2D material is to provide a supportive mesh that allows buffer space for volume expansions upon ion intercalation in the active material and establishes a continuous electronic contact. Therefore, the binding strength between both materials is crucial for the success of such electrodes. Furthermore, battery cycles may bring about phase transformations in the …

Synthesis And Characterization Of Graphene-Reinforced Polymer Filaments For Additive Manufacturing, Sean Menezes

Mechanical and Aerospace Engineering Theses

Fused Deposition Modeling (FDM) is a popular 3D printing process which uses a spool of thermoplastic polymer filament that is melted by the movable extruder printer head onto the bed to generate the required shape. The most used polymer filaments in FDM are Acrylonitrile Butadiene Styrene (ABS) and Poly Lactic Acid (PLA). However, these conventional polymer filaments have lower mechanical strength and are more susceptible to cracking as the cooler parts of the printed part shrink so much that they cause cracks to develop, leading to warping. The current investigation focuses on the synthesis of graphene, synthesis of polymer filaments …

Biosensor Devices Based On Graphene And 2d Materials, Suhada Poovathy

Theses

Nanomaterials offered new improvements and developments to the bio-sensing field due to their unique physical and chemical properties. Unique and exceptional electronic properties, such as the ultrahigh surface-to-volume ratio and the excellent electrical properties of the 2D materials like in graphene, making these materials promising for future smaller and faster electronics, but an extensive amount of research is still needed. This thesis is concerned with the study of the integration of 2D material graphene in the development of sensitive and rapid biosensors. The main objective of this thesis is to understand the features and characteristics of graphene, evaluate the scope …

Laser-Defined Graphene Strain Sensor Directly Fabricated On 3d-Printed Structure, Tyler M. Webb, Twinkle Pandhi, David Estrada

Materials Science and Engineering Faculty Publications and Presentations

A direct-write method to fabricate a strain sensor directly on a structure of interest is reported. In this method, a commercial graphene ink is printed as a square patch (6 mm square) on the structure. The patch is dried at 100 °C for 30 min to remove residual solvents but the printed graphene remains in an insulative state. By scanning a focused laser (830 nm, 100 mW), the graphene becomes electrically conductive and exhibits a piezoresistive effect and a low temperature coefficient of resistance of −0.0006 °C⁻¹. Using this approach, the laser defines a strain sensor pattern on …

Advances In The Synthesis And Application Of Anti-Fouling Membranes Using Two-Dimensional Nanomaterials, Asif Shahzad, Jae Min Oh, Mudassar Azam, Jibran Iqbal, Sabir Hussain, Waheed Miran, Kashif Rasool

All Works

This article provides a comprehensive review of the recent progress in the application of advanced two-dimensional nanomaterials (2DNMs) in membranes fabrication and application for water purification. The membranes fouling, its types, and anti-fouling mechanisms of different 2DNMs containing membrane systems are also discussed. The developments in membrane synthesis and modification using 2DNMs, especially graphene and graphene family materials, carbon nanotubes (CNTs), MXenes, and others are critically reviewed. Further, the application potential of next-generation 2DNMs-based membranes in water/wastewater treatment systems is surveyed. Finally, the current problems and future opportunities of applying 2DNMs for anti-fouling membranes are also debated.

Review: Factors Affecting Composite Laminates Against Lightning Strikes, Aaryan Manoj Nair

Publications and Research

Lightning strike protection (LSP) have recently been a newly developing field particularly with the emergence of graphene thin film integration into carbon fiber composite structures. This technology has a widespread application in airplanes, wind turbines, and other instruments which are susceptible to frequent lightning strikes. Electrical discharge of the instrument in a safe manner is vital for the safety of the passengers (in the case of flights) as well as the integrity of the aircraft structures because of their specific mechanical and structural properties, which are essential for their functioning. The purpose of the study is to fabricate graphene thin …

Fabrication And Characterization Of Photodetector Devices Based On Nanostructured Materials: Graphene And Colloidal Nanocrystals, Wafaa Gebril

Graduate Theses and Dissertations

Photodetectors are devices that capture light signals and convert them into electrical signals. High performance photodetectors are in demand in a variety of applications, such as optical communication, security, and environmental monitoring. Among many appealing nanomaterials for novel photodetection devices, graphene and semiconductor colloidal nanocrystals are promising candidates because of their desirable and unique properties compared to conventional materials.

Photodetector devices based on different types of nanostructured materials including graphene and colloidal nanocrystals were investigated. First, graphene layers were mechanically exfoliated and characterized for device fabrication. Self-powered few layers graphene phototransistors were studied. At zero drain voltage bias and room …

Investigation Of Bipolar Electrochemically Exfoliated Graphene For Supercapacitor Applications, Iman Khakpour

FIU Electronic Theses and Dissertations

Developing a reliable, simple, cost-efficient and eco-friendly method for scale-up production of high-quality graphene-based materials is essential for the broad applications of graphene. Up to now, various manufacturing methods have been employed for synthesizing high quality graphene, however aggregation and restacking has been a major issue and the majority of commercially available graphene products are actually graphite microplates. In this study, bipolar electrochemistry techniques have been used to exfoliate and deposit graphene nanosheets in a single-step process to enable high performance device application.

In the first part of this study, bipolar electrochemistry concept is utilized to design a single-step and …

Graphene As A Shielding Material For Sar Reduction In Human Head Using Rectangular And Circular Patch Antenna, Alka Singla Er., Anupma Marwaha Dr., Sanjay Marwaha Dr.

Karbala International Journal of Modern Science

Nanomaterials pave the way for better performance in wireless applications due to their unique properties. Nowadays, these have been used as shield material in dipole antennas for a solution of reduction in SAR value. This work proposes the use of emerging graphene nanomaterial by comparing the performance for two different shapes of patch antenna namely rectangular and circular patch. With the growth in technology, the protection of human health is also mandatory so the work is planned to use graphene as a shielding material for SAR reduction in the human brain and it is proved that for rectangular and circular …

Wastewater Remediation Technologies Using Macroscopic Graphene-Based Materials: A Perspective, Rajan Arjan Kalyan Hirani, Abdul Hannan Asif, Nasir Rafique, Lei Shi, Shu Zhang, Hong Wu, Hongqi Sun

Research outputs 2014 to 2021

Three-dimensional (3D) graphene-based macrostructures are being developed to combat the issues associated with two-dimensional (2D) graphene materials in practical applications. The 3D macrostructures (3DMs), for example, membranes, fibres, sponges, beads, and mats, can be formed by the self-assembly of 2D graphene-based precursors with exceptional surface area and unique chemistry. With rational design, the 3D macrostructures can then possess outstanding properties and exclusive structures. Thanks to various advantages, these macrostructures are competing in a variety of applications with promising performances unlike the traditional activated carbons, biochars and hydrochars, which have less flexibilities for modifications towards versatile applications. However, despite having such …

Biofabricated Constructs Of Carbon-Based Nanoparticles With Mesenchymal Stem Cells For Orthopedic Repair, Steven D. Newby

Doctoral Dissertations

Breakthroughs in tissue engineering are moving at a rapid rate especially in the regenerative bone biofabrication. Technology growth in the field of additive manufacturing (AM) such 3D bioprinting which provides the ability to create biocompatible 3D construct on which a cell source could be seeded is an encouraging substitute to autologous grafts.

This present research aims to biofabricate a construct for bone tissue engineering using AM technology. The biocompatible material was chosen corresponding to bones extracellular matrix (ECM) composition, which demonstrates an inorganic and organic development phase: Poly (lactic-glycolic acid) was chosen as the polymeric matrix of the compound, due …

Development Of A Laser-Assisted Chemical Vapor Deposition (Cvd) Technique To Grow Carbon-Based Materials, Abiodun Ademola Odusanya

MSU Graduate Theses

Carbon-based materials (CBMs) including graphene, carbon nanotubes (CNT), highly ordered pyrolytic graphite (HOPG), and pyrolytic carbon (PyC) have gained so much attention in research in recent years because of their unique electronic, optical, thermal, and mechanical properties. CBMs are relatively very stable and have minimal environmental footprint. Various techniques such as mechanical exfoliation, pulsed laser deposition, and chemical vapor deposition (CVD) have been used to grow CBMs and among them thermal CVD is the most common. This study aims to explore ways of reducing the energy requirement to produce CBMs, and for that, a novel pulsed laser-assisted CVD technique had …

Design Of Graphene-Based Sensors For Nucleic Acids Detection And Analysis, Asma’ Wasfi Fayez Mustafa

Dissertations

DNA (Deoxyribonucleic Acid) is the blueprint of life as it encodes all genetic information. In genetic disorder such as gene fusion, Copy Number Variation (CNV), and single nucleotide polymorphism, Nucleic acids such as DNA bases detection and analysis is used as the gold standard for successful diagnosis. Researchers have been conducting rigorous studies to achieve genome sequences at low cost while maintaining high accuracy and high throughput. A quick, accurate, and low-cost DNA detection approach would revolutionize medicine. Genome sequence helps to enhance people’s perception of inheritance, disease, and individuality. This research aims to improve DNA bases detection accuracy, and …

Recent Advances In Terahertz Photonic Technologies Based On Graphene And Their Applications, Tianjing Guo, Christos Argyropoulos

Department of Electrical and Computer Engineering: Faculty Publications

Graphene is a unique 2D material that has been extensively investigated due to its extraordinary photonic, electronic, thermal, and mechanical properties. Excited plasmons along its surface and other unique features are expected to play an important role in many emerging photonic technologies with drastically improved and tunable functionalities. This review is focused on presenting several recently introduced photonic phenomena based on graphene, beyond its usual linear response, such as nonlinear, active, topological, and nonreciprocal effects. The physical mechanisms and various envisioned photonic applications corresponding to these novel intriguing functionalities are also reported. The presented graphene-based technologies promise to revolutionize the …

Flexible Nanopaper Composed Of Wood-Derived Nanofibrillated Cellulose And Graphene Building Blocks, Qing Li, Ming Dai, Xueren Qian, Tian Liu, Zhenbo Liu, Yu Liu, Ming Chen, Wang He, Suqing Zeng, Yu Meng, Chenchen Dai, Jing Shen, Yingtao Liu, Wenshuai Chen, Wenbo Liu, Ping Lu

Faculty Scholarship for the College of Science & Mathematics

Nanopaper has attracted considerable interest in the fields of films and paper research. However, the challenge of integrating the many advantages of nanopaper still remains. Herein, we developed a facile strategy to fabricate multifunctional nanocomposite paper (NGCP) composed of wood-derived nanofibrillated cellulose (NFC) and graphene as building blocks. NFC suspension was consisted of long and entangled NFCs (10–30 nm in width) and their aggregates. Before NGCP formation, NFC was chemically modified with a silane coupling agent to ensure that it could interact strongly with graphene in NGCP. The resulting NGCP samples were flexible and could be bent repeatedly without any …

Quantum Simulations Of Low Dimensional Systems And Analytic Continuation Of Imaginary Time Correlation Functions, Nathan Scott Nichols

Graduate College Dissertations and Theses

For over thirty years, a long standing problem in quantum many-body physics has been to reliably extract dynamical information from imaginary time quantum Monte Carlo data. I report on a new method developed using modern evolutionary computation routines to approach this notoriously ill-posed problem. Motivation towards a solution will be presented as a brief summary of work on quantum simulations of low dimensional systems including helium on strained graphene and helium confined within rare gas plated mesoporous silica. The Differential Evolution for Analytic Continuation (DEAC) algorithm reconstructs the dynamic structure factor from imaginary time density-density correlations at zero and finite …

Experimental Validation Of Bulk-Graphene As A Thermoelectric Generator, Muhammad Uzair Khan, Amir Naveed, Syed Ehtisham Gillani, Dawar Awan, Muhammad Arif, Shaista Afridi, Muhammad Hamyun, Muhammad Asif, Saadia Tabassum, Muhammad Sadiq, Muhammad Lais, Muhammad Aslam, Saeed Ullah Jan, Zeeshan Ahad

Research outputs 2014 to 2021

Quest for alternate energy sources is the core of most of the research activities these days. No matter how small or large amount of energy can be produced by utilizing the non-conventional techniques and sources, every bit of innovation can reshape the future of energy. In this work, experimental analysis of the thermoelectric (TE) properties of bulk-graphene in the temperature range of (303 to 363) K is presented. Graphene powder was pressed to form a pellet which was used to fabricate the TE device. The effects of temperature on the Seebeck coefficient, electrical and thermal conductivities, and the dimensionless figure …

Semi-Empirical Modeling Of Liquid Carbon's Containerless Solidification, Philip C. Chrostoski

Doctoral Dissertations

“Elemental carbon has important structural diversity, ranging from nanotubes through graphite to diamond. Previous studies of micron-size core/rim carbon spheres extracted from primitive meteorites suggest they formed around such stars via the solidification of condensed carbon-vapor droplets, followed by gas-to-solid carbon coating to form the graphite rims. Similar core/rim particles result from the slow cooling of carbon vapor in the lab. The long-range carbon bond-order potential was used to computationally study liquid-like carbon in (1.8 g/cm³) periodic boundary (tiled-cube supercell) and containerless (isolated cluster) settings. Relaxations via conjugate-gradient and simulated-annealing nucleation and growth simulations using molecular dynamics were …

Two New Finite Element Schemes And Their Analysis For Modeling Of Wave Propagation In Graphene, Jichun Li

Mathematical Sciences Faculty Research

© 2020 The Author(s) In this paper, we investigate a system of governing equations for modeling wave propagation in graphene. Compared to our previous work (Yang et al., 2020), here we re-investigate the governing equations by eliminating two auxiliary unknowns from the original model. A totally new stability for the model is established for the first time. Since the finite element scheme proposed in Yang et al. (2020) is only first order in time, here we propose two new schemes with second order convergence in time for the simplified modeling equations. Discrete stabilities inheriting exactly the same form as the …

Additive Manufacturing Of Graphene-Based Devices For Flexible Hybrid Electronics, Twinkle Pandhi

Boise State University Theses and Dissertations

In this work, I investigate and enhance the fundamental sensing properties of printed electronic nanomaterials (e.g., graphene) in real-world environments while decreasing weight, cost, and power consumption. The dissertation addresses this issue with the following foci in mind: (1) developing a straightforward and repeatable process to synthesize graphene ink which is also compatible with Inkjet-printing (IJP) and Aerosol Jet printing (AJP). (2) Tuning additive manufacturing printing (IJP and AJP) parameters to establish a repeatable manufacturing process and print high performing (graphene-based) electrodes and interconnects, compatible with the underlying substrate. (3) Investigate power dissipation and electrical breakdown in AJP printed graphene …

Carbon Nanotube-On-Graphene Heterostructures, Yu Zheng, Dongmeng Li, Zubair Ahmed, Jeongwon Park, Changjian Zhou, Cary Y. Yang

Electrical and Computer Engineering

This paper presents a brief review of experimental and theoretical studies on a three-dimensional heterostructure consisting of vertical carbon nanotubes (CNTs) connected perpendicularly to a graphene layer. This structure can serve as a potential building block for an all-carbon network in energy storage devices and on-chip interconnects. The review highlights reported works on the fabrication and characterization of such a heterostructure, with focus on the effect of the CNT-graphene interface on electrical conduction. While a direct comparison between experiment and theory is not possible at this time, a brief survey of theoretical efforts based on atomic cluster models nonetheless reveals …

Recent Advances In Graphene-Based Materials For Fuel Cell Applications, Hanrui Su, Yun Hang Hu

Michigan Tech Publications

The unique chemical and physical properties of graphene and its derivatives (graphene oxide, heteroatom-doped graphene, and functionalized graphene) have stimulated tremendous efforts and made significant progress in fuel cell applications. This review focuses on the latest advances in the use of graphene-based materials in electrodes, electrolytes, and bipolar plates for fuel cells. The understanding of structure-activity relationships of metal-free heteroatom-doped graphene and graphene-supported catalysts was highlighted. The performances and advantages of graphene-based materials in membranes and bipolar plates were summarized. We also outlined the challenges and perspectives in using graphene-based materials for fuel cell applications.

A Review Of Inkjet Printed Graphene And Carbon Nanotubes Based Gas Sensors, Twinkle Pandhi, Ashita Chandnani, Harish Subbaraman, David Estrada

Materials Science and Engineering Faculty Publications and Presentations

Graphene and carbon nanotube (CNT)-based gas/vapor sensors have gained much traction for numerous applications over the last decade due to their excellent sensing performance at ambient conditions. Inkjet printing various forms of graphene (reduced graphene oxide or modified graphene) and CNT (single-wall nanotubes (SWNTs) or multiwall nanotubes (MWNTs)) nanomaterials allows fabrication onto flexible substrates which enable gas sensing applications in flexible electronics. This review focuses on their recent developments and provides an overview of the state-of-the-art in inkjet printing of graphene and CNT based sensors targeting gases, such as NO₂, Cl₂, CO₂, NH_{3 …}

Inkjet-Printed Graphene-Based 1 × 2 Phased Array Antenna, Mahmuda Akter Monne, Peter Mack Grubb, Harold Stern, Harish Subbaraman, Ray T. Chen, Maggie Yihong Chen

Electrical and Computer Engineering Faculty Publications and Presentations

Low-cost and conformal phased array antennas (PAAs) on flexible substrates are of particular interest in many applications. The major deterrents to developing flexible PAA systems are the difficulty in integrating antenna and electronics circuits on the flexible surface, as well as the bendability and oxidation rate of radiating elements and electronics circuits. In this research, graphene ink was developed from graphene flakes and used to inkjet print the radiating element and the active channel of field effect transistors (FETs). Bending and oxidation tests were carried out to validate the application of printed flexible graphene thin films in flexible electronics. An …

Market-Conscious Strategies To Improve The Performance And Stability Of Planar, P-I-N Hybrid Organic-Inorganic Metal Halide Perovskite Solar Cells, Brandon Dunham

Doctoral Dissertations

Planar, p-i-n (inverted) hybrid organic-inorganic perovskite solar cells that use low-temperature, solution-processable charge-transport layers have garnered much attention due to their direct compatibility with flexible substrates and cost-effective roll-to-roll manufacturing. Nevertheless, this architecture has failed to repeatedly achieve the superior power conversion efficiencies frequently attained by its n-i-p counterpart. Additionally, the perovskite active layer has poor stability in the presence of prolonged light exposure, high temperatures, and moisture. In this study, we propose commercially viable strategies to improve the performance and stability of inverted methylammonium lead iodide perovskite solar cells. First, we show that a simple two-step method comprising evaporation-induced …