Digital Commons Network^™

Mems Cantilever Sensor For Thz Photoacoustic Chemical Sensing And Spectroscopy, Nathan E. Glauvitz

Theses and Dissertations

Sensitive Microelectromechanical System (MEMS) cantilever designs were modeled, fabricated, and tested to measure the photoacoustic (PA) response of gasses to terahertz (THz) radiation. Surface and bulk micromachining technologies were employed to create the extremely sensitive devices that could detect very small changes in pressure. Fabricated devices were then tested in a custom made THz PA vacuum test chamber where the cantilever deflections caused by the photoacoustic effect were measured with a laser interferometer and iris beam clipped methods. The sensitive cantilever designs achieved a normalized noise equivalent absorption coefficient of 2.83x10^-10 cm^-1 W Hz^-1/2 using a 25 …

Modeling Reliability Growth In Accelerated Stress Testing, Jason K. Freels

Theses and Dissertations

Qualitative accelerated test methods improve system reliability by identifying and removing initial design flaws. However, schedule and cost constraints often preclude sufficient testing to generate a meaningful reliability estimate from the data obtained in these tests. In this dissertation a modified accelerated life test is proposed to assess the likelihood of attaining a reliability requirement based on tests of early system prototypes. Assuming each prototype contains an unknown number of independent competing failure modes whose respective times to occurrence are governed by a distinct Weibull law, the observed failure data from this qualitative test are shown to follow a poly-Weibull …

Water Vapor Movement In Freezing Aggregate Base Materials, Maile Anne Rogers

Theses and Dissertations

The objectives of this research were to 1) measure the extent to which water vapor movement results in water accumulation in freezing base materials; 2) evaluate the effect of soil stabilization on water vapor movement in freezing base materials; 3) determine if the corresponding changes in water content are sufficient to cause frost heave during winter; 4) determine if the corresponding changes in water content are sufficient to cause reductions in stiffness during spring; 5) evaluate relationships between selected material properties, freezing conditions, and the occurrence and impact of water vapor movement; and 6) numerically simulate heat and water movement …

A Dynamic Optimization Framework With Model Predictive Control Elements For Long Term Planning Of Capacity Investments In A District Energy System, Jose Luis Mojica Velazquez

Theses and Dissertations

The capacity expansion of a district heating system is studied with the objective of evaluating the investment decision timing and type of capacity expansion. District energy is an energy generation system that provides energy, such as heat and electricity, generated at central locations and distributed to the surrounding area. The study develops an optimization framework to find the optimal investment schedule over a 30 year horizon with the options of investing in traditional heating sources (boilers) or a next-generation combined heat and power (CHP) plant that can provide heat and electricity. In district energy systems, the investment decision on the …

A Kinetic Study Of Aqueous Calcium Carbonate, Derek Daniel Harris

Theses and Dissertations

Amorphous calcium carbonate (ACC) precipitation is modeled using particle nucleation, growth, and aggregation. The particles are tracked in terms of their radial size and particle density using direct quadrature method of moments (DQMOM). Four separate nucleation models are implemented and are compared to experimental data. In discord with a recent study, it is shown that classical nucleation, coupled with equilibrium chemistry, is in good agreement with experimental data. Novel nucleation mechanisms are presented which fit the experimental data with slightly greater accuracy. Using equilibrium chemistry it is shown that the equilibrium value of ACC is pKeq = 7.74 at 24C, …

Frost Susceptibility Of Base Materials Treated With Asphalt Emulsion, Noelle Anderson

Theses and Dissertations

The objective of this research was to investigate emulsion-treated base (ETB) frost susceptibility in terms of both freeze-thaw cycling and frost heave. The research performed in this study involved laboratory testing of ETB materials sampled from both the Redwood Road and 7800 South reconstruction projects in northern Utah. The effects of freeze-thaw cycling were evaluated by comparing the stiffness and strength of tested specimens to the same properties of control specimens not subjected to freeze-thaw cycling. Frost heave testing enabled evaluation of the effects of emulsion content and degree of curing on the volumetric stability of ETB materials during sustained …

Developing Guidelines For Including Mobility-Based Performance Specifications In Highway Construction Contracts, Shawn J. Larson

Theses and Dissertations

Construction zones can greatly affect the traffic flow on roadways, especially when lane closures are required. Traditionally, the Utah Department of Transportation (UDOT) has used traffic management specifications that only allow lane closures and road work to be done during predetermined hours or specifications that require a certain number of lanes to be open at all times. Recently, mobility-based work-zone traffic flow maintenance has been considered. This method requires continuous monitoring of mobility-based performance data and a mechanism to send alerts to the contractors when the mobility data does not meet the standards set by the specifications. UDOT recently tested …

Condition Assessment Of Decommissioned Bridge Decks Treated With Waterproofing Membranes And Asphalt Overlays, Eric Scott Sumsion

Theses and Dissertations

The objective of this research was to assess the condition of four decommissioned bridge decks treated with waterproofing membranes and asphalt overlays following the completion of their service lives. Large samples were cut from each of the bridge decks immediately prior to demolition and taken to the Brigham Young University Highway Materials Laboratory, where extensive sampling and testing was performed. Methods used to evaluate the condition of the bridge deck samples included visual inspection, hammer sounding, Schmidt rebound hammer testing, resistivity testing, half-cell potential testing, linear polarization testing, cover depth measurement, and chloride concentration measurement. The samples were removed from …

Liquid Core Waveguide Sensors With Single And Multi-Spot Excitation, Lynnell Uilani Wai Yee Zempoaltecatl

Theses and Dissertations

Using silicon based microfabrication and materials, a photonic platform, capable of single bioparticle analysis, has been developed. This platform combines liquid and hollow core waveguides on the micron-scale (5 µm x 12 µm) to isolate femtoliter sized sample volumes. Fluorescence excitation and signals in the visible range are directed into and out of the sample volume at an orthogonal angle to maximize signal-to-noise. In order to guide light in a low-index material antiresonant reflecting optical waveguides (ARROWs) were incorporated into the platform. This thesis reveals the development path of these structures over several device generations including innovations in material, geometries, …

Modified Sodium Diuranate Process For The Recovery Of Uranium From Uranium Hexafluoride Transport Cylinder Wash Solution, Austin Dean Meredith

Theses and Dissertations

Uranium hexafluoride (UF₆) containment cylinders must be emptied and washed every five years in order to undergo recertification, according to ANSI standards. During the emptying of the UF₆ from the cylinders, a thin residue, or heel, of UF₆ is left behind. This heel must be removed in order for recertification to take place.

To remove it, the inside of the containment cylinder is washed with acid and the resulting solution generally contains three or four kilograms of uranium. Thus, before the liquid solution can be disposed of, the uranium must be separated. A modified sodium diuranate …

Fundamental Experimental Studies In Scaling, Blast Mitigation And Material Processing, Xing Zhao

Theses and Dissertations

In this work, two separate research efforts are discussed. They include experimental studies in (1) Scaling and Blast Mitigation and (2) Scaling in Friction Stir Extrusion. In both studies, the primary experimental measurement method is three-dimensional digital image correlation (3D-DIC), a non-contacting full-field measurement method that is applicable for both high-rate loading and quasi-static loading conditions.

Scaling and Blast Mitigation Studies:

A series of properly scaled structures was subjected to buried blast loading conditions via detonation of a small explosive buried in saturated sand. Using high speed stereo-vision systems to record the deformations of selected regions on the upper surface …

Automatic Modulation Recognition For Aeronautical Telemetry, Jacob William Frogget

Theses and Dissertations

This these explores automatic modulation recognition as applied to PCM/FM, SOQPSK- TG and ARTM CPM. It found that the likelihood based approach is intractable. The statistical features of the amplitude, phase and frequency are ineffective at distinguishing these modulation types. A method based on the phase changes between symbols is developed and shows that as long as symbol timing is established, this method can effectively distinguish PCM/FM, SOQPSK-TG and ARTM CPM for signal-to-noise ratios above 30 dB. Another method, the Bianchi-Loubaton- Sirven technique, was able to distinguish PCM/FM and SOQPSK-TG but was unable to distinguish ARTM CPM. A happy byproduct …

Delamination Detection In Concrete Using Disposable Impactors For Excitation, Anjali Narendra Patil

Theses and Dissertations

Delaminations in concrete bridge decks result primarily from corrosion of the reinforcing bars (or rebar). This corrosion leads to volumetric expansion of the rebar. When the rebar expands, concrete cracks, and there is a localized separation of the concrete cover from the underlying concrete. Impact-echo testing is an effective technique to map delaminations on concrete bridge decks. However, mapping speed is limited by necessary retrieval of the impactor for traditional tests. To achieve higher scanning speeds, it is advantageous to use both a non-contact measurement (air-coupled impact-echo) and disposable-impactor excitation. Disposable impactors have the potential advantage of achieving greater deck …

Effect Of Full-Annular Pressure Pulses On Axial Turbine Performance, Mark H. Fernelius

Theses and Dissertations

Pulse detonation engines show potential to increase the efficiency of conventional gas turbine engines if used in place of the steady combustor. However, since the interaction of pressure pulses with the turbine is not yet well understood, a rig was built to compare steady flow with pulsing flow. Compressed air is used in place of combustion gases and pressure pulses are created by rotating a ball valve with a motor. This work accomplishes two main objectives that are different from previous research in this area. First, steady flow through an axial turbine is compared with full annular pulsed flow closely …

The Performance Of Risk Management And Innovation In Construction Manager/General Contractor Delivery In Civil Construction Applications, Rebecca M. Owens

Theses and Dissertations

Project teams that deliver high risk, complex projects in the civil construction industry need tools to enable successful delivery. Construction Manager/General Contractor (CM/GC) is an innovative alternate delivery method, providing one such a tool. CM/GC furnishes public agencies with an attractive option for delivering projects in a less adversarial and more constructive manner by involving the contractor during design. The sophisticated public owner does not have to relinquish control of the details of the design in order to accelerate the schedule or see the benefits of real-time cost estimating data. There are also significant cost and schedule benefits with not …

An Experimental Analysis Of The Weighted Sum Of Spatial Gradients Minimization Quantity In Active Structural Acoustic Control Of Vibrating Plates, Daniel R. Hendricks

Theses and Dissertations

Active Structural Acoustic Control (ASAC) is a subcategory of the more widely known field of Active Noise control (ANC). ASAC is different from traditional ANC methods because it seeks to attenuate noise by altering the noise producing structure instead of altering the acoustic waves traveling through the air. The greatest challenge currently facing ASAC researchers is that a suitable parameter has not yet been discovered which can be easily implemented as the minimization quantity in the control algorithms. Many parameters have been tried but none effectively attenuate the sound radiation in a way that can be easily implemented. A new …

Computational And Experimental Study Of Degeneration, Damage And Failure In Biological Soft Tissues, Gregory Allen Von Forell

Theses and Dissertations

The purpose of this work was to analyze the biomechanics of degeneration, damage, and failure in biological soft tissues both experimentally and computationally to provide insight into tendon or ligament tearing, tendo-achilles lengthening and lumbar spine dysfunction. For soft tissue tearing, experimental studies for calculating fracture toughness were performed and determined that tendons and ligaments are able to completely resist tear propagation. For tendo-achilles lengthening, a damage model was developed to mimic the behavior of the lengthening that occurs as a result of the percutaneous triple hemisection technique. The model provided insight for predicting the amount of lengthening that occurs …

Molecular Modeling Of Dna For A Mechanistic Understanding Of Hybridization, Terry Jacob Schmitt

Theses and Dissertations

DNA microarrays are a potentially disruptive technology in the medical field, but their use in such settings is limited by poor reliability. Microarrays work on the principle of hybridization and can only be as reliable as this process is robust, yet little is known at the molecular level about how the surface affects the hybridization process. This work uses advanced molecular simulation techniques and an experimentally-parameterized coarse-grain model to determine the mechanism by which hybridization occurs on surfaces and to identify key factors that influence the accuracy of DNA microarrays. Comparing behavior in the bulk and on the surface showed, …

Active Structural Acoustic Control Of Clamped And Ribbed Plates, William Richard Johnson

Theses and Dissertations

A control metric, the weighted sum of spatial gradients (WSSG), has been developed for use in active structural acoustic control (ASAC). Previous development of WSSG [1] showed that it was an effective control metric on simply supported plates, while being simpler to measure than other control metrics, such as volume velocity. The purpose of the current work is to demonstrate that the previous research can be generalized to plates with a wider variety of boundary conditions and on less ideal plates. Two classes of plates have been considered: clamped flat plates, and ribbed plates. On clamped flat plates an analytical …

Introducing The Vuepod: Development And Testing Of A Low-Cost Large-Scale Stereoscopic Immersive System Using 3d Lcd Televisions, Shane Makana Hayden

Theses and Dissertations

3D immersive visualization systems, or CAVEs™, have found wide adoption for use in geosciences, planetary science, medical research, and computer science. However, much of the potential for such systems in practical civil and environmental engineering settings has been severely limited due to 1) extreme costs in both hardware and software; 2) immobility due to calibration and darkroom requirements; and 3) extensive and expensive manpower requirements for both operation and maintenance. This thesis presents the development and testing of a new mobile low-cost immersive stereo visualization system -- the "VuePod" -- that attempts to address these challenges through the use of …

The Design And Validation Of A Computational Rigid Body Model For Study Of The Radial Head, Cassandra Woodcock

Theses and Dissertations

Rigid body modeling has historically been used to study various features of the elbow joint including both physical and computational models. Computational modeling provides an inexpensive, easily customizable, and effective method by which to predict and investigate the response of a physiological system to in vivo stresses and applied perturbations. Utilizing computer topography scans of a cadaveric elbow, a virtual representation of the joint was created using the commercially available MIMICS(TM) and SolidWorks(TM) software packages. Accurate 3D articular surfaces, ligamentous constraints, and joint contact parameters dictated motion. The model was validated against two cadaveric studies performed by Chanlalit et al. …

Localization Of Auditory Spatial Targets In Sighted And Blind Subjects, Richard Nuckols

Theses and Dissertations

This research was designed to investigate the fundamental nature in which blind people utilize audible cues to attend to their surroundings. Knowledge on how blind people respond to external spatial stimuli is expected to assist in development of better tools for helping people with visual disabilities navigate their environment. There was also interest in determining how blind people compare to sighted people in auditory localization tasks. The ability of sighted individuals, blindfolded individuals, and blind individuals in localizing spatial auditory targets was assessed. An acoustic display board allowed the researcher to provide multiple sound presentations to the subjects. The subjects’ …

Intercalibration Of Quikscat And Oscat Land Backscatter, John Colin Barrus

Theses and Dissertations

The Ku-band SeaWinds-on-QuikSCAT scatterometer (QuikSCAT) operated continuously from 1999 to 2009. Though its primary mission was to estimate global ocean winds, QuikSCAT has proven useful in a variety of geophysical studies using land backscatter measurements. The end of the primary QuikSCAT mission in 2009 has prompted interest for continuing the QuikSCAT land dataset with other scatterometers. The Oceansat-2 scatterometer (OSCAT), launched in 2009, is a viable candidate for continuing the QuikSCAT time series because of the similarities of both sensors in function and design. An important difference in the sensors is that they operate at slightly different incidence angles. Continuing …

Examination Of The Effect Of Different Training Metrics On Performance Of A Minimally Invasive Surgery Transfer Task, Cristofer Madera

Theses and Dissertations

The purpose of this experiment was to determine if there existed techniques to more efficiently train prospective surgeons the skills necessary to capably perform minimally invasive surgical procedures. Also, we wanted to know if trainees could be pushed to cognitively define a laparoscopic environment with a novel hand-eye relationship. To explore these questions, a simulation was setup wherein subjects would perform a laparoscopic transfer task and receive active feedback during training. Different subjects would receive different metrics as feedback and a comparison would be made between subjects with respect to standard metrics. Results of this experiment show that all subjects …

Structural Analysis And Optimization Of Skyscrapers Connected With Skybridges And Atria, Amy Jean Taylor Mccall

Theses and Dissertations

Skybridges and atria between buildings are becoming more and more popular. Most current skybridge connections are either roller or rigid-connections. This dissertation presents an investigation of the structural analysis and optimization of skyscraper systems with hinge-connected skybridges, and compares the results to skyscraper systems with roller-connected skybridges and to skyscraper systems without skybridges altogether. Also presented is an investigation of the structural analysis and optimization of skyscrapers both with and without atria between the buildings. It was assumed that the atria envelope was constructed with cushions made from lightweight, transparent, and flexible Ethylene Tetrafluoroethylene (ETFE). A simplified skyscraper skybridge model …

Polarization Diversity In The Presence Of Multipath Propagation, Grant Taylor Wagner

Theses and Dissertations

The possibility of polarization diversity using left and right hand circular polarization (LHCP and RHCP) in the presence of multipath propagation is examined. We show that there are differences in the received signal for LHCP and RHCP for a number of realistic scenarios. Because multipath propagation can produce different LHCP and RCHP signals, there exists the possibility for diversity improvement involving the two polarizations.

Cooperative Target Tracking Enhanced With The Sequence Memoizer, Everett A. Bryan

Theses and Dissertations

Target tracking is an important part of video surveillance from a UAV. Tracking a target in an urban environment can be difficult because of the number of occlusions present in the environment. If multiple UAVs are used to track a target and the target behavior is learned autonomously by the UAV then the task may become easier. This thesis explores the hypothesis that an existing cooperative control algorithm can be enhanced by a language modeling algorithm to improve over time the target tracking performance of one or more ground targets in a dense urban environment. Observations of target behavior are …

Patient-Specific Modeling Of Adult Acquired Flatfoot Deformity Before And After Surgery, Edward Meade Spratley

Theses and Dissertations

The use of computational modeling is an increasingly commonplace technique for the investigation of biomechanics in intact and pathological musculoskeletal systems. Moreover, given the robust and repeatable nature of computer simulation and the prevalence of software techniques for accurate 3-D reconstructions of tissues, the predictive power of these models has increased dramatically. However, there are no patient-specific kinematic models whose function is dictated solely by physiologic soft-tissue constraints, articular shape and contact, and without idealized joint approximations. Moreover, very few models have attempted to predict surgical effects combined with postoperative validation of those predictions. Given this, it is not surprising …

Exploring Hybrid Spm-Cache Architectures To Improve Performance And Energy Efficiency For Real-Time Computing, Lan Wu

Theses and Dissertations

Real-time computing is not just fast computing but time-predictable computing. Many tasks in safety-critical embedded real-time systems have hard real-time characteristics. Failure to meet deadlines may result in the loss of life or in large damages. Known of Worst Case Execution Time (WCET) is important for reliability or correct functional behavior of the system. As multi-core processors are increasingly adopted in industry, it has become a great challenge to accurately bound the worst-case execution time (WCET) for real-time systems running on multi-core chips. This is particularly true because of the inter-thread interferences in accessing shared resources on multi-cores, such as …

On Relay Node Placement Problem For Survivable Wireless Sensor Networks, Changyong Jung

Theses and Dissertations

Wireless sensor networks are widely applied to many fields such as animal habitat monitoring, air traffic control, and health monitoring. One of the current problems with wireless sensor networks is the ability to overcome communication failures due to hardware failure, distributing sensors in an uneven geographic area, or unexpected obstacles between sensors. One common solution to overcome this problem is to place a minimum number of relay nodes among sensors so that the communication among sensors is guaranteed. This is called Relay Node Placement Problem (RNP). This problem has been proved as NP-hard for a simple connected graph. Therefore, many …