Digital Commons Network^™

Impact Of Photovoltaic System Penetration On The Operation Of Voltage Regulator Equipment, Abesh Sorab Mubaraki

Master's Theses

The growing popularity of photovoltaic (PV) generation systems leads to an increase in the number of residential and commercial grid-tied PV systems that interconnect to the distribution circuit. This affects the characteristics of the distribution circuit; for example, the assumption that the voltage profile of a radial line decreases down-stream becomes invalid because of the addition of the PV system on the line. This poses new challenges when setting the parameters of voltage regulating devices. Add to that the fact that PV systems are intermittent, especially on cloudy days, which make the line even more difficult to regulate, and the …

Portable Solar Powered Charging Station, Jordan Bonner

Electrical Engineering

The portable solar powered charging station uses a solar powered mat that can be folded for portability. The device has the ability to charge small electronics during both day and night. When sunlight is available, the charger charges two C batteries in series and at the same time it charges any electronic device that can be connected via USB or cigarette lighter. At night the charger will charge the same electronic devices from the onboard batteries. The charging station must be able to interface with electronic devices using USB and a car cigarette lighter to charge the device’s battery.

Multipolymer Interactions In Bulk Heterojunction Photovoltaic Devices, Grant Olson

Physics

Multipolymer photovoltaics, single layer devices made up of multiple photoactive polymers, can create organic photovoltaics (OPVs) with a wider spectral response than single polymer systems without the difficult fabrication of a tandem. Our group has successfully created multipolymer solar devices with 2% power conversion efficiency. We have analyzed the optical and electrical properties of these devices, and found that it may be possible for polymers to assist each other with charge extraction, though combining polymers disrupts single polymer crystallinity.

Solar Powered Led Lantern For Developing Countries, Lacy Billingsly Iii

Electrical Engineering

In recent years, both LED and solar technology have become the focus of sustainable energy. LED lighting uses significantly less power than its fluorescent competitor. Solar cells enable clean, natural, and portable power. As these two entities become more efficient at exponential rates, the hope for the wide use of off-grid lighting in less developed countries seemingly increases at the same rate. Currently, there has been a development of industry for portable solar powered lighting systems. Before designing a product, a study was conducted of current products on the market that aim to light dark homes. This study and design …

Modeling And Analysis Of A Photovoltaic System With A Distributed Energy Storage System, Anthony Winston Ma

Master's Theses

As California continues to integrate more renewable energy into its electrical system, the state has experienced a corresponding rise in photovoltaic system installations. PV arrays are a unique source of power generation in that they are affected by the location of the sun, shading, and temperature changes. These characteristics make solar one of the most highly variable forms of renewable energy. In order to improve solar power’s consistency, PV systems require a supplemental source of power. The primary focus of this paper is to determine if distributed energy storage systems can be used to reduce the effect of solar intermittency. …

Design And Construction Of A Solar Operated Gate, Jacob Gardener

BioResource and Agricultural Engineering

This senior project discusses the design and construction of a solar operated gate. A solar panel is used to charge a battery, and then an inverter is used to run a garage door opener off the battery. The garage door opener operates a short lever arm which is connected to a longer lever arm which is connected to the gate. Each component and mounting mechanisms were designed and built to effectively provide the gate opening function. The finished product operates well, the gate opens in about 8 seconds after the button is pressed on the remote controller or wall mount …

Final Design Review: Design Of An Integrated Solar Cell Array To Power A Solar Ear Hearing Aid Battery Recharger, Christina (Chrissa) Blattner, Scott Carey, Jared Myren, Faye Siao

Materials Engineering

As the energy of fossil fuel supplies are fast depleting due to high consumptions of energy by human beings, the need for other sources of energy, such as solar energy, has become a viable option. By creating solar cell arrays the desired voltage can be generated. The overall goal of the Solar Ear project is to create an array of photovoltaic cells connected with aluminum tracings to recharge batteries that are specifically used for hearing aids. The goal embodies two main areas: the design of a processing method to connect the cells during a micro-fabrication process and the creation of …

Portable Solar Desalination System, Genaro Sanchez, Alan Galarza, Erick Del Real

Electrical Engineering

Clean water and reliable energy can be difficult to obtain in remote locations such as desert villages, secluded islands, and other places where no fresh water can be found. The primary goal for this project is address these problems by implementing a portable desalinization plant system that is to be powered by solar energy PV system as the main energy source.

Solar Powered Electric Clothes Dryer, Roger Mai, Alan Swe

Electrical Engineering

Appliances that consume the most energy in a household usually involve heating, and an electric clothes dryer is one such appliance, consuming up to 4KW of power. The most environmentally friendly way is to hang clothes outside to dry, a natural solar and wind powered method, but unfortunately most people are unable to do so as some neighborhood communities do not allow the hanging of laundry outside as it is regarded as “unsightly”, for example. This project aims to provide an alternate solution to the wall-powered electric clothes dryer by designing one which operates entirely off the grid.

Solar Instrumentation Lab, Rene Canedo Iii, Rong Gui Chen

Electrical Engineering

This project is a mobile platform that will allow experiments on different solar panels to be done easily while keeping the cost of the lab to a minimum. California Polytechnic State University’s motto is ‘learn by doing’ and this lab structure will allow students to get practical experience with photovoltaic cells and the instruments that are required to take measurements. The solar instrumentation lab is a potential hardware lab for the electrical engineering department’s Sustainable Electric Energy Conversion class EE 420 and Solar-Photovoltaic Systems Design EE 520. This group took the current solar structure as a base for the lab’s …

Photovoltaic Emulator Adaptable To Irradiance, Temperature And Panel Specific I-V Curves, Joseph Gamos Durago

Master's Theses

This thesis analyzes the design and performance of a photovoltaic (PV) emulator. With increasing interest in renewable energies, large amounts of money and effort are being put into research and development for photovoltaic systems. The larger interest in PV systems has increased demand for appropriate equipment with which to test PV systems.

A photovoltaic emulator is a power supply with similar current and voltage characteristics as a PV panel. This work uses an existing power supply which is manipulated via Labview to emulate a photovoltaic panel. The emulator calculates a current-voltage (I-V) curve based on the user specified parameters of …

Off-Grid Photovoltaic System Design Project, Brian Duffy

Electrical Engineering

This project uses the BP SX 150S solar panel to charge a 12 V battery. This battery powers an AIMS 400 W Modified Sine Wave Inverter to provide 120 V RMS AC power to a load of up to 40 W. Inverter efficiency was measured at different load conditions. A control circuit was implemented to prevent overcharging or over-discharging of the battery, by disconnecting it from the panel or the load, respectively. The control circuit turn-on and cutoff voltages were measured versus battery voltage, and the on-resistance of the MOSFET switches was measured for various load currents. A table of …

Enhanced Cal Poly Super System Simulink Model, Matthew Ogden Mcfarland

Master's Theses

The Cal Poly Sustainable Power for Electrical Resources (SuPER) project is a solar power DC distribution system designed to autonomously manage and supply the energy needs of a single family off-the-grid home. The following thesis describes the improvement and re-design of a MATLAB Simulink model for the Cal Poly SuPER system. This model includes a photovoltaic (PV) array, a lead-acid gel battery with temperature effects, a wind turbine model, a re-designed DC-DC converter, a DC microgrid, and multiple loads. This thesis will also include several control algorithms such as a temperature controlled thermoelectric (T.E.) cooler, intelligent load switching, and an …

Simulation Of Cal Poly Super System Simulink Model Using Insolation Variation, Jacob Kory

Electrical Engineering

This senior project focuses on simulation of the Cal Poly SuPER system using an insolation model. First, local and historical weather data is examined to determine the range of limits that the model will utilize. Then, the insolation model is constructed to fit into the existing SuPER model. The overall system is tested under a variety of insolation values to determine system performance of motor and static loads. Based on these simulations, several factors of the current model are discovered that limit the power consumption profile under off-peak load conditions. Finally, recommendations on improvements to the model are discussed

Dual Axis Solar Tracker, Weston Sapia, Jason Birnie

Electrical Engineering

No abstract provided.

Multidisciplinary Design Optimization Of An Extreme Aspect Ratio Hale Uav, Bryan J. Morrisey

Master's Theses

ABSTRACT

Multidisciplinary Design Optimization of an Extreme Aspect Ratio HALE UAV

Bryan J. Morrisey

Development of High Altitude Long Endurance (HALE) aircraft systems is part of a vision for a low cost communications/surveillance capability. Applications of a multi payload aircraft operating for extended periods at stratospheric altitudes span military and civil genres and support battlefield operations, communications, atmospheric or agricultural monitoring, surveillance, and other disciplines that may currently require satellite-based infrastructure. Presently, several development efforts are underway in this field, including a project sponsored by DARPA that aims at producing an aircraft that can sustain flight for multiple years and …