Social and Behavioral Sciences Commons^™

Photonic Chip Based Tunable Slow And Fast Light Via Stimulated Brillouin Scattering, Ravi Pant, Adam Byrnes, Christopher Poulton, Enbang Li, Duk-Yong Choi, Stephen J. Madden, Barry Luther-Davies, Benjamin J. Eggleton

Faculty of Engineering and Information Sciences - Papers: Part A

We report the first (to our knowledge) demonstration of photonic chip based tunable slow and fast light via stimulated Brillouin scattering. Slow, fast, and negative group velocities were observed in a 7 cm long chalcogenide (As2S3) rib waveguide with a group index change ranging from ∼−44 to +130, which results in a maximum delay of ∼23  ns at a relatively low gain of ∼23  dB. Demonstration of large tunable delays in a chip scale device opens up applications such as frequency sensing and true-time delay for a phased array antenna, where integration and delays ∼10  ns are highly desirable.

Acoustic Emission Monitoring Of Split Formation During Charpy Impact Testing Of High Strength Steel, Andrii Kostryzhev, R B. Punch, Claire L. Davis, Martin Strangwood

Faculty of Engineering and Information Sciences - Papers: Part A

Acoustic emission (AE) monitoring has been used to detect split formation during room temperature low blow Charpy impact testing of high strength thick strip steels. The AE signal analysis identified separate signals originating from hammer impact, plastic deformation (verified using Charpy impact testing on mild steel with no splits) and split initiation/growth. The presence of splits was confirmed by sectioning and fractography, and the splits were brittle in nature. A possible correlation between the AE signal features and fracture mode is presented.

Effects Of Cultural Cognitive Styles On Users Evaluation Of Website Complexity, Tingru Cui, Xinwei Wang, Hock Hai Teo

Faculty of Engineering and Information Sciences - Papers: Part A

The internationalization of websites requires compelling navigation experience for users from diverse cultures. This research investigates the effects of cultural cognitive styles on user perception of website complexity and the subsequent influence on user satisfaction towards the website. More specifically, the website complexity is examined along three dimensions: component, coordinative, and dynamic. Laboratory experiments involving participants from China and United States were used to test the hypotheses. The results showed that the effect of objective complexity on perceived complexity is contingent on cultural cognitive styles. People with holistic and analytic cultural cognitive styles display different perceptions of website complexity. This …

The Sensitivity Of Particle Parameters In Discrete Element Modelling Of Belt Conveyor Transfers, David B. Hastie, Peter W. Wypych

Faculty of Engineering and Information Sciences - Papers: Part A

As discrete element modelling (DEM) becomes more widely used as a design tool, its suitability to modelling belt conveyor applications including conveyor transfers and conveyor trajectories is becoming more recognised. The accuracy of the data inputted for both the system geometry and particle perspective are vital if the outputs obtained from DEM simulations are to be considered valid. Bench-scale testing can readily obtain a range of particle parameters, however, there are others that can be more difficult to determine. This paper focuses on two such parameters; coefficient of rolling friction and shear modulus. A series of sensitivity analyses have been …

Reducing Cogging Force In A Cage-Secondary Linear Induction Motor (Lim) By One-Side Shifting, Mochammad Rusli

Faculty of Engineering and Information Sciences - Papers: Part A

High precision linear machining tools is one of interesting research field in related to high qualitative products which is also becoming one of competitive factor. The movement precision can be affected by existence of ripple force, unpredicted external load and frictional force. The existence of cogging force is the one limited factor of the linear precision. The reduction of cogging force of its linear movement precision of machining tools using rotary motor drive can be obtained by the skewed rotor or implement the feedback control system. Many researchers have conducted the reduction of cogging torque of its machining tools drive …

Effect Of Gallium Doping And Ball Milling Process On The Thermoelectric Performance Of N-Type Zno, Priyanka Jood, Germanas Peleckis, Xiaolin Wang, S X. Dou

Faculty of Engineering and Information Sciences - Papers: Part A

We report a systematic investigation of the thermoelectric properties of n-type Ga-doped ZnO synthesized using different ball milling conditions. Samples fabricated by the high-energy ball milling resulted in a highly dense layered structure with randomly distributed voids. These samples measured the lowest room temperature thermal conductivity, i.e., 27 W/mK due to increased phonon scattering. Furthermore, the Ga:ZnO system showed a metal–semiconductor transition above 300 K with transition temperature decreasing with increasing doping level. Measurement of the activation energy revealed the presence of one donor level around 3.9–7.8 meV and a deeper donor level around 15.4–18.1 meV below the conduction band …

Teaching Monte Carlo Codes At University: Development Of A Geant4 Course For Students Of Schools Of Physics, Susanna Guatelli, Dean Cutajar, Anatoly B. Rosenfeld, Catherine Layton

Faculty of Engineering and Information Sciences - Papers: Part A

Nowadays, it is important that students of Schools of Physics include the study of Monte Carlo codes in their curriculum as these codes are widely used in research. At the School of Engineering Physics of the University of Wollongong, we designed and set in place a Geant4 course addressed to the Medical Physics domain. In this paper, we illustrate the main features of the course and its development since 2010. The design of this course maybe adopted to teach Geant4 or any other Monte Carlo code, and in general to teach complex software tools to students with limited computing background. …

Energy Storage For Renewable Energy, Saugato Mukerji

Faculty of Engineering and Information Sciences - Papers: Part A

Presented at All Energy Australia 2012 International Conference, Melbourne

Reliability-Based Conversion Of A Structural Design Code For Railway Prestressed Concrete Sleepers, A M. Remennikov, Martin Murray, Sakdirat Kaewunruen

Faculty of Engineering and Information Sciences - Papers: Part A

"Ballasted railway track is very suitable for heavy-rail networks because of its many superior advantages in design, construction, short- and long-term maintenance, sustainability, and life cycle cost. An important part of the railway track system, which distributes the wheel load to the formation, is the railway sleeper. Improved knowledge has raised concerns about design techniques for prestressed concrete (PC) sleepers. Most current design codes for these rely on allowable stresses and material strength reductions. However, premature cracking of PC sleepers has been found in railway tracks. The major cause of cracking is the infrequent but high-magnitude wheel loads produced by …

Multifactor Optimization Of A Fuzzy-Pid Controller Using Genetic Algorithm, Xiaofeng He, Wei Chen, Bihai Zhu, Zhengyi Jiang, Christopher David Cook

Faculty of Engineering and Information Sciences - Papers: Part A

The design of a Fuzzy-PID controller involves setting the fuzzy rules, membership functions and its associated scaling factors. How to obtain a better control result and how these scaling factors affect the controller's performance are still a challenge. In this paper, the automatic position control system of a Hille 100 experimental rolling mill was used as a research testbed. Based on the mathematical control model of the rolling mill, a Fuzzy-PID controller was developed, and the process of implementing global optimization considering all these factors simultaneously by using genetic algorithm is introduced in detail. Through simulation, the performance of the …

Nonlinear Inelastic Behavior Of Circular Concrete-Filled Steel Tubular Slender Beam-Columns With Preload Effects, Vipulkumar Ishvarbhai Patel, Qing Quan Liang, Muhammad N. Hadi

Faculty of Engineering and Information Sciences - Papers: Part A

This paper presents a numerical model based on fiber element formulations for simulating the nonlinear inelastic behavior of eccentrically loaded circular concrete-filled steel tubular (CFST) slender beam-columns with preload effects. Deflections caused by preloads are included in the global analysis of CFST slender beam-columns as initial geometric imperfections. Computational algorithms based on the Müller's method are developed to obtain load-deflection responses of CFST slender beam-columns including preload effects. The accuracy of the numerical model is examined by comparisons of computer solutions with experimental results. The numerical model is utilized to investigate the effects of preloads on the axial load-deflection curves, …

Recent Progress On Programming Methods For Industrial Robots, Zengxi Pan, Joseph Polden, Nathan Larkin, Stephen Van Duin, John Norrish

Faculty of Engineering and Information Sciences - Papers: Part A

"Although an automated flexible production cell is an intriguing prospect for small to median enterprises (SMEs) in current global market conditions, the complexity of programming remains one of the major hurdles preventing automation using industrial robots for SMEs. This paper provides a comprehensive review of the recent research progresses on the programming methods for industrial robots, including online programming, offline programming (OLP), and programming using Augmented Reality (AR). With the development of more powerful 3D CAD/PLM software, computer vision, sensor technology, etc. new programming methods suitable for SMEs are expected to grow in years to come. (C) 2011 Elsevier Ltd. …

Mechanics Of Design And Model Development Of Cvc-Plus Roll Curve, Jianzhong Xu, Dianyao Gong, Zhengyi Jiang, Xianghua Liu, Guodong Wang

Faculty of Engineering and Information Sciences - Papers: Part A

The mathematic model of CVC-Plus work roll curve is built. The ratio of the initial shifting value to the target crown is determined, and the mathematical model considering the relationship between the coefficients A2, A3, A4, A5 and is established. According to the theoretical analysis, the distance between the maximum or minimum point of the high order equivalent crown for work roll with CVC-plus roll curve and the rolling central point is the times of the roll barrel length. In general, the initial shifting value of the CVC-plus roll curve is not equal to the initial shifting value of the …

Towards Formalizing A Reputation System For Cheating Detection In Peer-To-Peer-Based Massively Multiplayer Online Games, Willy Susilo, Yang-Wai Chow, Rungrat Wiangsripanawan

Faculty of Engineering and Information Sciences - Papers: Part A

The rapidly growing popularity of Massively Multiplayer Online Games (MMOGs) has given rise to an increase in the number of players world wide. MMOGs enable many players interact together through a shared sense of presence created by the game. The Peer-to-Peer (P2P) network topology overcomes communication bottleneck problems associated with centralized client/server sys- tems. Thus, P2P-based MMOGs are seen as the way of the future, and many dierent P2P-based MMOG architectures have been proposed to date. However, many architectures are proposed in an ad hoc manner and enhancing the security of such systems is an elusive research problem. In this …

Optimization Of Welding Parameters For Repairing Nial Bronze Components, Huijun Li, Daniel Grudgings, Nathan P. Larkin, John Norrish, Mark Callaghan, Lenka Kuzmikova

Faculty of Engineering and Information Sciences - Papers: Part A

The objective of this study is to determine an optimal welding procedure that can be implemented to repair damaged Nickel Aluminium Bronze (NAB) components. NAB is commonly used in marine applications where components are subject to a constant corrosive environment and high stresses. Research into ideal NAB microstructure for a marine application, was performed in order to gain a baseline for experimental analysis of potential welding procedures. The results indicated that the welding repair can be performed with a wide range of heat input. The effect of post-weld heat treatment (PWHT) on the microstructure and mechanical properties in the heat …

Biocompatible Ferroelectric (Na,K)Nbo3 Nanofibers, A Jalalian, A M. Grishin

Faculty of Engineering and Information Sciences - Papers: Part A

"Dense homogeneous textile composed from continuous bead-free sodium potassium niobate (NKN) nanofibers 100 mu m long and 50-200 nm in diameter was sintered by sol-gel calcination assisted electrospinning. High resolution electron microscopy and x-ray diffraction revealed preferential cube-on-cube growth of fibers in [001] direction. Raman spectrum of NKN fibers contains all the features characteristic to electrically poled orthorhombic phase. In contrast to polycrystalline ceramics, it shows relative enhancement of the Raman cross section of isotropic A(1g)(nu(1)) mode compared with polar axis defined F(2g)(nu(5)) and E(g)(nu(2)) vibrations. We interpret this as an evidence for superparaelectric state of NKN nanofibers. Spontaneous polarization …

Integrated Seat And Suspension Control For A Quarter Car With Driver Model, Haiping Du, Weihua Li, Nong Zhang

Faculty of Engineering and Information Sciences - Papers: Part A

In this paper, an integrated vehicle seat and sus pension control strategy for a quarter car with driver model is proposed to improve suspension performance on driver ride comfort. An integrated seat and suspension model that includes a quarter-car suspension, a seat suspension, and a 4-degree-of freedom (DOM) driver body model is presented first. This in1 tegrated model provides a platform to evaluate ride comfort 1performance in terms of driver head acceleration responses under typical road disturbances and to develop an integrated control of seat and car suspensions. Based on the integrated model, an H∞ state feedback controller is designed …

Performance Of A Reinforced Embankment On A Sensitive Champlain Clay Deposit, Chalermpol Taechakumthorn, R K. Rowe

Faculty of Engineering and Information Sciences - Papers: Part A

An existing elastoviscoplastic constitutive model is modified using concepts of the state-dependent fluidity parameters and the damage law, to incorporate the effect of soil structure and its destructuration. The model is employed to simulate the performance of a well-documented case study of the reinforced test embankment constructed over a sensitive Champlain clay deposit at Saint Alban, Quebec. The finite element calculations, using both the original (nonstructured) and modified (structured) elastoviscoplastic soil models, are compared with the observed field data from a test embankment brought to failure. The results from the structured elastoviscoplastic soil model show better agreements with the field …

Nonlinear Analysis Of Biaxially Loaded High Strength Rectangular Concrete-Filled Steel Tubular Slender Beam-Columns, Part I: Theory, Qing Quan Liang, Vipulkumar Ishvarbhai Patel, Muhammad N. S Hadi

Faculty of Engineering and Information Sciences - Papers: Part A

This paper presents a new numerical model for the nonlinear inelastic analysis of biaxially loaded high strength thin-walled rectangular concrete-filled steel tubular (CFST) slender beam-columns. The numerical model considers the effects of progressive local buckling, initial geometric imperfections, high strength materials and second order. The accurate fiber element method is used to model the inelastic behavior of composite cross-sections. Theoretical models are developed that simulate the load-deflection responses and strength envelopes of thin-walled rectangular CFST slender beamcolumns under biaxial loads. New computational algorithms based on the M􀂗􁈷 ller's method are developed to adjust the depth and orientation of the neutral …

The Benefits Of Introducing Electronic Health Records In Residential Aged Care Facilities: A Multiple Case Study, Yiting Zhang, Ping Yu, Jun Shen

Faculty of Engineering and Information Sciences - Papers: Part A

Purpose: Information and communications technology solutions have been introduced into the residential aged care system in order to improve the effectiveness and efficiency of aged care, however to date, the actual benefits have not been systematically analysed. The aim of this study was to identify the benefits of electronic health records (EHR) in residential aged care services and to examine how the benefits have been achieved. Method: A qualitative interview study was conducted in nine residential aged care facilities (RACFs) belonging to three organisations in the Australian Capital Territory (ACT), New South Wales (NSW) and Queensland, Australia. A longitudinal investigation …

Replication Of Polypyrrole With Photonic Structures From Butterfly Wings As Biosensor, Jie Tang, Shenmin Zhu, Zhixin Chen, Chuanliang Feng, Yanjun Shen, Fan Yao, Di Zhang, Won-Jin Moon, Deok-Min Song

Faculty of Engineering and Information Sciences - Papers: Part A

Polypyrrole (PPy) with photonic crystal structures were synthesized from Morpho butterfly wings using a two-step templating process. In the first step photonic crystal SiO2 butterfly wings were synthesized from Morpho butterfly wings and in the second step the SiO2 butterfly wings were used as templates for the replication of PPy butterfly wings using an in situ polymerization method. The SiO2 templates were then removed from the PPy butterfly wings using a HF solution. The hierarchical structures down to the nanometer level, especially the photonic crystal structures, were retained in the final PPy replicas, as evidenced directly by field-emission scanning electron …

Strain-Induced Phase Transformation During Thermo-Mechanical Processing Of Titanium Alloys, A Dehghan-Manshadi, Rian J. Dippenaar

Faculty of Engineering and Information Sciences - Papers: Part A

Strain-induced phase transformation studies have been conducted in a Ti-6Al-2Sn-4Zr-6Mo alloy. This alloy was subjected to b sub-transus deformation upon slow cooling from the b-phase field and the effect of strain on the extent and morphology of the phase transformation during hot-deformation was determined. In addition, the transformation kinetics and the morphology of the newly formed a-phase were studied following deformation under different cooling conditions. By applying strain, the rate of the b-to-a phase transformation increased significantly during deformation as well as during slow cooling following deformation. This increase in the kinetics of the b-to-a transformation can be ascribed to …

Comparison Of Some Tests Of Fit For The Inverse Gaussian Distribution, D J. Best, John C. W Rayner, Olivier Thas

Faculty of Engineering and Information Sciences - Papers: Part A

This paper gives an empirical investigation of some tests of goodness of fit for the inverse Gaussian distribution.

Distortion Behavior Of A Heavy Hydro Turbine Blade Casting During Forced Air Cooling In Normalizing Treatment Process, Hailiang Yu, Jinwu Kang, T J. Wang, J A. Ma, Y Y. Hu, Tianyou Huang, S B. Wang, Y Wu, C C. Zhang, Yan-Tao Dai, P Li

Faculty of Engineering and Information Sciences - Papers: Part A

Distortion behavior of blade castings in heat treatment process determines their geometrical accuracy, and improper control of it may result in additional repair, shape righting, or even rejection. This article presents a novel approach for discovering the distortion behavior of heavy blade castings during heat treatment process in production. Real-time measurements of distortion and temperature field of a heavy hydro turbine blade casting weighted 17 ton during forced air cooling in normalizing treatment process were carried out by using deformation measurement instruments and an infrared thermal imaging camera. The distortion processes of the typical locations of blade and the temperature …

Marginalized Exponential Random Graph Models, Thomas F. Suesse

Faculty of Engineering and Information Sciences - Papers: Part A

Exponential random graph models (ERGMs) are a popular tool for modeling social networks representing relational data, such as working relationships or friendships. Data on exogenous variables relating to participants in the network, such as gender or age, are also often collected. ERGMs allow modeling of the effects of such exogenous variables on the joint distribution, specified by the ERGM, but not on the marginal probabilities of observing a relationship. In this article, we consider an approach to modeling a network that uses an ERGM for the joint distribution of the network, but then marginally constrains the fit to agree with …

Double Space-Time Transmit Diversity For Very High Data Rate Mb-Ofdm Uwb Systems, Ngoc P. Le, Le C. Tran, Farzad Safaei

Faculty of Engineering and Information Sciences - Papers: Part A

In this paper, we investigate a multiband-orthogonal frequency division multiplexing ultra-wideband (MB-OFDM UWB) system with very high data rates (VHDR) of several gigabits per second (Gbps). We propose a DSTTD-based VHDR MB-OFDM UWB system by incorporating a double space-time transmit diversity (DSTTD) scheme into the conventional MB-OFDM UWB system. At the receiver, an efficient soft-demapper that takes into consideration the noise enhancement due to a zero-forcing equalization is developed. Numerical simulations of the proposed system at a very high data rate of 2.Gbps over the IEEE 802.15.3a channel models are implemented. The simulation results show that this system could achieve …

Order-4 Orthogonal Cooperative Communication In Space-Time-Frequency Coded Mb-Ofdm Uwb, Zixuan Lin, Le C. Tran, Farzad Safaei

Faculty of Engineering and Information Sciences - Papers: Part A

The combination of cooperative communication and Space-Time-Frequency-Codes (STFCs) has been recently proposed in the literature for Multiband OFDM Ultra-Wideband (MB-OFDM UWB) to improve the bit error performance, system capacity, data rate and wireless communications range. This paper proposes a cooperative communication design using Order-4 Orthogonal STFCs in MB-OFDM UWB systems, which is referred to as Order-4 Orthogonal Cooperative Communication Scheme (4-OCCS). It will be shown that 4-OCCS improves significantly the diversity and error performance of the MB-OFDM UWB system, compared to the conventional MB-OFDM UWB (without STFCs) as well as our Order-2 Orthogonal Cooperative Communication Scheme using Alamouti STFCs (2-OCCS) …

The Work Pattern Of Personal Care Workers In Two Australian Nursing Homes: A Time-Motion Study, Siyu Qian, Ping Yu, Zhen-Yu Zhang, David M. Hailey, Pamela J. Davy, Mark Nelson

Faculty of Engineering and Information Sciences - Papers: Part A

Background: The aim of the study is to describe the work pattern of personal care workers (PCWs) in nursing homes. This knowledge is important for staff performance appraisal, task allocation and scheduling. It will also support funding allocation based on activities.

Methods: A time-motion study was conducted in 2010 at two Australian nursing homes. The observation at Site 1 was between the hours of 7:00 and 14:00 or 15:00 for 14 days. One PCW was observed on each day. The observation at Site 2 was from 10:00 to 17:00 for 16 days. One PCW working on a morning shift and …

Patients Perceptions Of Web Self-Service Applications In Primary Healthcare, Xin Zhang, Ping Yu, Jun Yan, Hongxiang Hu, Niraj Goureia

Faculty of Engineering and Information Sciences - Papers: Part A

This paper presents the preliminary findings of a case study of patients' acceptance and usage of web self-service - online appointment system - in a primary health care centre in a regional area in Australia. After two months of implementation, structured interviews were undertaken over three months to ascertain patients' perceptions of the web self-service application. The findings indicates that patients' acceptance of the web self-service application maybe hindered by their relative lower computer ownership or inadequate computer skills and access to the internet, their preference for flexible personal communication for appointment making and inadequate flexibility of the appointment system …

Social Implications Of Technology: The Past, The Present, And The Future, Karl Stephan, Katina Michael, M. G. Michael, Laura Jacob, Emily Anesta

Faculty of Engineering and Information Sciences - Papers: Part A

The social implications of a wide variety of technologies are the subject matter of the IEEE Society on Social Implications of Technology (SSIT). This paper reviews the SSIT’s contributions since the Society’s founding in 1982, and surveys the outlook for certain key technologies that may have significant social impacts in the future. Military and security technologies, always of significant interest to SSIT, may become more autonomous with less human intervention, and this may have both good and bad consequences. We examine some current trends such as mobile, wearable, and pervasive computing, and find both dangers and opportunities in these trends. …