Physics Commons^™

Optical Micro-Seismometer Based On Evanescent Field Perturbation Of Whispering Gallery Modes, Jaime Da Silva

Mechanical Engineering Research Theses and Dissertations

This thesis proposes a light-weight, compact, and accurate optical micro-seismometer that could be used in many applications, such as planetary exploration. The sensor proposed here is based on the principle of whispering gallery optical mode (WGM) resonance shifts of a dielectric micro-resonator due to disturbances of its evanescent field. The micro-seismometer could be used in place of the traditional bulky seismometers. The design of a waveguide-resonator and mechanical structure to disturb the evanescent field are presented. A proof-of-concept a seismometer model that uses a 5µm ring resonator is numerically tested with actual seismic data. The results show that a WGM-based …

Design, Layout, And Testing Of Sige Apds Fabricated In A Bicmos Process, Dane Laurence Gentry

UNLV Theses, Dissertations, Professional Papers, and Capstones

This Thesis is concerned with the design, layout, and testing of avalanche photodiodes (APDs). APDs are a type of photodetector and, thus, convert light signals into electrical signals (current or voltage). APDs can be fabricated using silicon (Si). In this Thesis, however, three integrated circuit (IC) chips containing various silicon-germanium (SiGe) APDs with different sizes, structures, and geometries were designed, laid out, and fabricated using the Austriamicrosystems (AMS) 0.35μm SiGe BiCMOS (S35) process. This was done in order to compare SiGe APDs to Si only APDs and investigate the hypothesis that SiGe APDs are capable of detecting longer wavelengths than …

Application Of Silicon Nanohair Textured P-N Junctions In A Photovoltaic Device, Michael Small

Electronic Theses and Dissertations

The goal of this project is to design and develop a fabrication process for a silicon photovoltaic device which incorporates a nanohair textured p-n junction. The silicon nanowires are etched into a silicon wafer, comprising an epitaxial p-layer on n-substrate, via metal-assisted chemical etching (MACE). The resulting nanowires contain p-n junctions that lie along the length of the vertical nanowires. This construct has the potential to increase the optical bandwidth of a silicon photovoltaic device by allowing a greater amount of short wavelength light to reach the junction. In addition, the MACE method of nanofabrication has the potential for decreasing …

Optimizing The Plasmonic Enhancement Of Light In Metallic Nanogap Structures For Surface-Enhanced Raman Spectroscopy, Stephen Joseph Bauman

Graduate Theses and Dissertations

Technology based on the interaction between light and matter has entered something of a renaissance over the past few decades due to improved control over the creation of nanoscale patterns. Tunable nanofabrication has benefitted optical sensing, by which light is used to detect the presence or quantity of various substances. Through methods such as Raman spectroscopy, the optical spectra of solid, liquid, or gaseous samples act as fingerprints which help identify a single type of molecule amongst a background of potentially many other chemicals. This technique therefore offers great benefit to applications such as biomedical sensors, airport security, industrial waste …

Improving Detection Of Dim Targets: Optimization Of A Moment-Based Detection Algorithm, Shannon R. Young

Theses and Dissertations

Wide area motion imagery (WAMI) sensor technology is advancing rapidly. Increases in frame rates and detector array sizes have led to a dramatic increase in the volume of data that can be acquired. Without a corresponding increase in analytical manpower, much of these data remain underutilized. This creates a need for fast, automated, and robust methods for detecting dim, moving signals of interest. Current approaches fall into two categories: detect-before-track (DBT) and track-before-detect (TBD) methods. The DBT methods use thresholding to reduce the quantity of data to be processed, making real time implementation practical but at the cost of the …

Exfoliation, Synthesis, And Characterization Of Nanoscale Te, Takayuki Hironaka

Graduate Theses and Dissertations

Since the experimental discovery of graphene, two dimensional materials have enjoyed more attention and emphasis in academic research than nanowires, but the latter are an important area of study for creating 1D materials, or single atom chains, the next generation materials for advancing electronic devices. Atomically thin layers can be generated from 2D materials with weak bonds in one direction, and by applying this concept to one dimensional weakly bonded materials, we hypothesize that single atom chains with atomic-scale diameters may be produced. Tellurium (Te) and selenium (Se) have lattices consisting of spiral chains oriented along the c-axis, and each …

Fabrication And Characterization Of Electrochemical Glucose Sensors, Mohammed Marie

Graduate Theses and Dissertations

Electrochemical sensors based on the nanostructure of the semiconductor materials are of tremendous interest to be utilized for glucose monitoring. The sensors, based on the nanostructure of the semiconductor materials, are the third generations of the glucose sensors that are fast, sensitive, and cost-effect for glucose monitoring.

Glucose sensors based on pure zinc oxide nanorods (NRs) grown on different substrates, such ITO, FTO, and Si/SiO2/Au, were investigated in this research. Silicon nanowire (NW)- based glucose sensors were also studied. First, an enzyme-based glucose sensor was fabricated out of glass/ITO/ZnO NRs/BSA/GOx/nafion membrane. The sensor was tested amperometrically at different glucose concentrations. …

Effective Magnetic And Electric Response Of Composite Materials, Mona Hassan Alsaleh

Doctoral Dissertations

Metamaterials (MMs) are nanocomposite materials consisting of metal-dielectric resonators much smaller in size than the wavelength of the incident light. Common examples of metamaterials are based on split ring resonators (SRRs), parallel wires or strips and fishnet structures. These types of materials are designed and fabricated in order to provide unique optical responses to the incident electromagnetic radiation that are not available in naturally existing materials. The MMs can exhibit unusual properties such as strong magnetism at terahertz (THz) and optical frequencies. Additionally, negative index materials (NIMs) can provide negative index of refraction which can be used in many applications …

Electromagnetic Wave-Matter Interactions In Complex Opto-Electronic Materials And Devices, Raj Kumar Vinnakota

Doctoral Dissertations

This dissertation explores the fundamentals of light-matter interaction towards applications in the field of Opto-electronic and plasmonic devices. In its core, this dissertation attempts and succeeds in the the modeling of light-matter interactions, which is of high importance for better understanding the rich physics underlying the dynamics of electromagnetic field interactions with charged particles. Here, we have developed a self-consistent multi-physics model of electromagnetism, semiconductor physics and thermal effects which can be readily applied to the field of plasmotronics and Selective Laser Melting (SLM). Plasmotronics; a sub-field of photonics has experienced a renaissance in recent years by providing a large …

Physical Electronic Properties Of Self-Assembled 2d And 3d Surface Mounted Metal-Organic Frameworks, Radwan Elzein

USF Tampa Graduate Theses and Dissertations

Metal-organic frameworks stand at the frontiers of molecular electronic research because they combine desirable physical properties of organic and inorganic components. They are crystalline porous solids constructed by inorganic nodes coordinated to organic ligands to form 1D, 2D, or 3D structures. They possess unique characteristics such as ultrahigh surface area crystal lattices up to 10000 m² g^-1, and tunable nanoporous sizes ranging from 0.2 to 50 nm. Their unprecedented structural diversity and flexibility beyond solid state materials can lead to unique properties such as tailorable electronic and ionic conductivity which can serve as interesting platforms for a …

Genetic Algorithm Design Of Photonic Crystals For Energy-Efficient Ultrafast Laser Transmitters, Troy A. Hutchins-Delgado

Shared Knowledge Conference

Photonic crystals allow light to be controlled and manipulated such that novel photonic devices can be created. We are interested in using photonic crystals to increase the energy efficiency of our semiconductor whistle-geometry ring lasers. A photonic crystal will enable us to reduce the ring size, while maintaining confinement, thereby reducing its operating power. Photonic crystals can also exhibit slow light that will increase the interaction with the material. This will increase the gain, and therefore, lower the threshold for lasing to occur. Designing a photonic crystal for a particular application can be a challenge due to its number of …

Investigation On The Rons And Bactericidal Effects Induced By He + O2 Cold Plasma Jets: In Open Air And In An Airtight Chamber, Han Xu, Dingxin Liu, Weitao Wang, Zhijie Liu, Li Guo, Mingzhe Rong, Michael G. Kong

Bioelectrics Publications

He + O₂ plasma jets in open air and in an airtight chamber are comparatively studied, with respect to their production of gaseous/aqueous reactive species and their antibacterial effects. Under the same discharge power, the plasma jet in open air has higher densities of gaseous reactive species and a higher concentration of aqueous H₂O₂ but lower concentrations of aqueous OH and O₂^-. In addition, the increase in the O₂ ratio in He in both plasma jets causes a linear decrease in the population of gaseous reactive species, except for O(3p⁵P) …

Vortex Structures Inside Spherical Mesoscopic Superconductor Plus Magnetic Dipole, A. Ludu

Publications

We investigate the existence of multivortex states in a superconducting mesoscopic sphere with a magnetic dipole placed at the center. We obtain analytic solutions for the order parameter inside the sphere through the linearized Ginzburg-Landau (GL) model, coupled with mixed boundary conditions, and under regularity conditions and decoupling coordinates approximation. The solutions of the linear GL equation are obtained in terms of Heun double confluent functions, in dipole coordinates symmetry. The analyticity of the solutions and the associated eigenproblem are discussed thoroughly. We minimize the free energy for the fully nonlinear GL system by using linear combinations of linear analytic …

Effects Of Fabrication Errors On The Focusing Performance Of A Sector Metalens, S. S. Stafeev, A. G. Nalimov, Liam O’Faolain, M. V. Kotlyar

Cappa Publications

Using e-beam lithography, a 16-sector spiral metalens was fabricated in an amorphous silicon, capable of converting linearly polarized incident light into an azimuthally polarized optical vortex. When illuminated by a 633-nm linearly polarized laser beam, the metalens generated a near-surface subwavelength focal spot equal to 0.75 of the incident wavelength at full-width of half-maximum intensity. The focusing performance of the spiral metalens was numerically shown to be sensitive to the deviation of the factual microrelief from the calculated height. For the designed microrelief height, a circularly polarized incident beam was focused into a bright ring with a reverse energy flow …

Parallel Algorithms For Time Dependent Density Functional Theory In Real-Space And Real-Time, James Kestyn

Doctoral Dissertations

Density functional theory (DFT) and time dependent density functional theory (TDDFT) have had great success solving for ground state and excited states properties of molecules, solids and nanostructures. However, these problems are particularly hard to scale. Both the size of the discrete system and the number of needed eigenstates increase with the number of electrons. A complete parallel framework for DFT and TDDFT calculations applied to molecules and nanostructures is presented in this dissertation. This includes the development of custom numerical algorithms for eigenvalue problems and linear systems. New functionality in the FEAST eigenvalue solver presents an additional level of …

Application And Evaluation Of Lighthouse Technology For Precision Motion Capture, Soumitra Sitole

Masters Theses

This thesis presents the development towards a system that can capture and quantify motion for applications in biomechanical and medical fields demanding precision motion tracking using the lighthouse technology. Commercially known as SteamVR tracking, the lighthouse technology is a motion tracking system developed for virtual reality applications that makes use of patterned infrared light sources to highlight trackers (objects embedded with photodiodes) to obtain their pose or spatial position and orientation. Current motion capture systems such as the camera-based motion capture are expensive and not readily available outside of research labs. This thesis provides a case for low-cost motion capture …

Indirect Imaging Using Computational Imaging Techniques, Aparna Viswanath

Electrical Engineering Theses and Dissertations

The work describes various methods employed towards solving the problem of indirect imaging. Computational techniques are employed to indirectly decipher information about an object hidden from view of a camera. Notion of virtualizing the source of illumination and detectors on real world rough surfaces was exploited to construct a non line of sight computational imager. Diversity was explored from the stand point of both illumination of the object and imaging of light reflected from the object. To understand the impact of scattering by real world rough surfaces, an instrument was developed that allows characterization of isoplanatic angle for different surface …

No2- And No3- Enhance Cold Atmospheric Plasma Induced Cancer Cell Death By Generation Of Onoo-, Dehui Xu, Qingjie Cui, Yujing Xu, Zhijie Liu, Zeyu Chen, Wenjie Xia, Hao Zhang, Dingxin Liu, Hailan Chen, Michael G. Kong

Bioelectrics Publications

Cold atmospheric plasma (CAP) is a rapidly developed technology that has been widely applied in biomedicine especially in cancer treatment. Due to the generation of various active species in plasma, CAP could induce various tumor cells death and showed a promising potential in cancer therapy. To enhance the biological effects of gas plasma, changing the discharging parameters is the most commonly used method, yet increasing discharging power will lead to a higher possibility of simultaneously damage surrounding tissues. In this study, by adding nontoxic concentration of additional nitrite and nitrate in the medium, we found that anti-tumor effect of CAP …

Interface Model Of Pem Fuel Cell Membrane Steady-Dtate Behavior, Russell L. Edwards, Ayodeji Demuren

Mechanical & Aerospace Engineering Faculty Publications

Modeling works which simulate the proton-exchange membrane fuel cell with the computational fluid dynamics approach involve the simultaneous solution of multiple, interconnected physics equations for fluid flows, heat transport, electrochemical reactions, and both protonic and electronic conduction. Modeling efforts vary by how they treat the physics within and adjacent to the membrane-electrode assembly (MEA). Certain approaches treat the MEA not as part of the computational domain, but rather an interface connecting the anode and cathode computational domains. These approaches may lack the ability to consistently model catalyst layer losses and MEA ohmic resistance. This work presents an upgraded interface formulation …

Electrostatic Design And Conditioning Of A Triple Point Junction Shield For A −200 Kv Dc High Voltage Photogun, G. Palacios-Serrano, F. Hannon, C. Hernandez-Garcia, M. Poelker, H. Baumgart

Electrical & Computer Engineering Faculty Publications

Nuclear physics experiments performed at the Continuous Electron Beam Accelerator Facility (CEBAF) at the Jefferson Lab require a DC high voltage photogun to generate polarized electron beams from GaAs photocathodes. The photogun uses a tapered ceramic insulator that extends into the vacuum chamber and mechanically holds the cathode electrode. Increasing the operating voltage from nominal −130 kV to −200 kV will provide lower beam emittance, better transmission through injector apertures, and improved photocathode lifetime. This desire to increase the photogun operating voltage led to the design of a triple-point-junction shield electrode which minimizes the electric field at the delicate insulator-metal-vacuum …

Tailoring The Asymmetric Magnetoimpedance Response In Exchange-Biased Ni - Fe Multilayers, Ufuk Kilic, Carolina Ross, Carlos Garcia

Ufuk Kilic

Instrumentation For Cryogenic Dynamic Nuclear Polarization And Electron Decoupling In Rotating Solids, Faith Joellen Scott

Arts & Sciences Electronic Theses and Dissertations

Dynamic nuclear polarization (DNP) increases the sensitivity of nuclear magnetic resonance (NMR) using the higher polarization of electron radical spins compared to nuclear spins. The addition of electron radicals for DNP to the sample can cause hyperfine broadening, which decreases the resolution of the NMR resonances due to hyperfine interactions between electron and nuclear spins. Electron decoupling has been shown to attenuate the effects of hyperfine coupling in rotating solids. Magic angle spinning (MAS) DNP with electron decoupling requires a high electron Rabi frequency provided by a high-power microwave source such as a frequency-agile gyrotron. This dissertation describes the development …

A Simple Method Of Coil Design, M. Rawlik, A. Eggenberger, J. Krempel, Christopher Crawford, K. Kirch, F. M. Piegsa, G. Quéméner

Physics and Astronomy Faculty Publications

In this article, we present a method to design a coil producing an arbitrarily shaped magnetic field by restricting the path of the coil's wires to a regular grid. The solution is then found by a simple least squares minimum. We discuss practical applications, in particular, in the active magnetic field stabilization system of the neutron electric dipole moment experiment at the Paul Scherrer Institute in Villigen, Switzerland. We also publish the software implementation of the method.

Room Temperature Operation Of Quantum Cascade Lasers Monolithically Integrated Onto A Lattice-Mismatched Substrate, Rowel Go

Electronic Theses and Dissertations

Quantum Cascade Lasers (QCLs) are semiconductor devices that, currently, have been observed to emit radiation from ~ 2.6 μm to 250 μm (1 to 100 terahertz range of frequencies.) They have established themselves as the laser of choice for spectroscopic gas sensing in the mid-wavelength infrared (3-8 μm) and long-wavelength infrared (8-15 μm) region. In the 4-12 μm wavelength region, the highest performing QCL devices, in terms of wall-plug efficiency and continuous wave operation, are indium phosphide (InP) based. The ultimate goal is to incorporate this InP-based QCL technology to silicon (Si) substrate since most opto-electronics are Si-based. The main …

High Dynamic Range Optical Devices And Applications., Elijah Robert Jensen

Electronic Theses and Dissertations

Much of what we know about fundamental physical law and the universe derives from observations and measurements using optical methods. The passive use of the electromagnetic spectrum can be the best way of studying physical phenomenon in general with minimal disturbance of the system in the process. While for many applications ambient visible light is sufficient, light outside of the visible range may convey more information. The signals of interest are also often a small fraction of the background, and their changes occur on time scales so quickly that they are visually imperceptible. This thesis reports techniques and technologies developed …

Novel Compact Narrow-Linewidth Mid-Infrared Lasers For Sensing Applications, Behsan Behzadi

Optical Science and Engineering ETDs

The mid-infrared (2-14 μm) spectral region contains the strong absorption lines of many important molecular species, which make this region crucial for several well-know applications such as spectroscopy, chemical and biochemical sensing, security, and industrial monitoring. To fully exploit this region through absorption spectroscopic techniques, compact and low-cost narrow-linewidth (NLW) mid-infrared (MIR) laser sources are of primary importance.

This thesis is focused on three novel compact NLW MIR lasers: demonstration and characterization of a new glass-based spherical microlaser, investigation of the performance of a novel fiber laser, and the design of a monolithic laser on a silicon chip. Starting with …

Generation Of Large-Volume Diffuse Plasma By An External Ionization Wave From A Single-Electrode Plasma Jet, Seyed Hamid Razavi Barzoki

Electrical & Computer Engineering Theses & Dissertations

A non-thermal transient diffuse plasma can be generated remotely in a nonconductive reduced pressure chamber by an external guided fast ionization wave (FIW). We found that an atmospheric-pressure low-temperature plasma jet (APPJ) can be a source of FIW which transfers an enhanced electric field at the wave front across a reduced pressure Pyrex glass chamber with no electrical connection to the chamber. Here, we studied the formation and propagation of the APPJ plasma, the interaction of atmospheric-pressure guided FIW with a dielectric surface which forms the wall of the reduced-pressure system, and the formation and propagation of the reduce-pressure FIW …

Investigation Of The Skin Effect In Alternating Currents, Matthew Liang

The International Student Science Fair 2018

My research is on the investigation of the skin effect in alternating currents. The skin effect is when an alternating current tends to flow on the surface of the conductor, such that the current density is highest near the surface, and decreases with greater depths in the conductor. This is due to the alternating current inducing changing magnetic fields, which in turn induces currents that oppose the original flow of current, resisting the current flowing through the centre the most. This reduces the effective cross-sectional area of the conductor and increases the resistance, causing increased power losses. This effect becomes …

Energy Conversion System For Travelers (Ecost), Thipok Bovornratanaraks

The International Student Science Fair 2018

We have innovated “The Energy Conversion System for Travelers” or the ECoST. With the fact that most travelers have wheeled cabin-bags, whilst walking, the wheels will rotate so why don’t we harvest electricity from this kinetic energy? We thus install our innovation, the ECoST, to the bag to generate electricity from the spinning wheels. The electricity is then kept in the storage unit and ready to charge your empty battery devices in an emergency case via a USB port. To make life easy, our ECoST was designed to replicate the power bank charging method; therefore, we can charge …

The Relationship Between Electrical Conductivity And Magnetically Damped Motion, Kalem Akhtar

The International Student Science Fair 2018

Varying electrical conductivities of different, non-magnetic metals appears to affect the magnitude of magnetically damped motion. To determine the relationship between magnetic damping and conductivity an experiment was designed using different length tubes of aluminium, copper and brass. The tubes had the same diameter and similar wall thickness. A short, cylindrical neodymium magnet was dropped through the tubes of and the time for the magnet to traverse the tube was recorded using a smartphone camera. These times allowed for the terminal velocity to be calculated for each metal length and the average terminal velocity for each metal was determined. This …