Engineering Commons^™

Investigation Of 2195 And 2219 Post Weld Heat Treatments For Additive Friction Stir Lap Welds, Matthew Champagne

University of New Orleans Theses and Dissertations

To evaluate potential uses for friction stir welding in additive manufacturing, two separate parts were fabricated, one of 2195-T84 and the other 2219-T87, utilizing fixed pin techniques and additive lap welds. The parts were cut into samples, artificially aged and subjected to Rockwell hardness (HRB), Vickers hardness, micrographic photography, and metallographic imaging on both pre- and post- heat treatment. Additionally, tensile testing was performed on the heat-treated samples. A comparisons of test results showed a minimal increase in the yield strength of the 2195-T84 samples compared to as-welded tensile results obtained from a previous project. The ultimate tensile strength was …

Synthetic Jet Actuator-Based Aircraft Tracking Using A Continuous Robust Nonlinear Control Strategy, N. Ramos-Pedroza, W. Mackunis, M. Reyhanoglu

Publications

A robust nonlinear control law that achieves trajectory tracking control for unmanned aerial vehicles (UAVs) equipped with synthetic jet actuators (SJAs) is presented in this paper. A key challenge in the control design is that the dynamic characteristics of SJAs are nonlinear and contain parametric uncertainty. The challenge resulting from the uncertain SJA actuator parameters is mitigated via innovative algebraic manipulation in the tracking error system derivation along with a robust nonlinear control law employing constant SJA parameter estimates. A key contribution of the paper is a rigorous analysis of the range of SJA actuator parameter uncertainty within which asymptotic …

Design, Manufacture, And Structural Dynamic Analysis Of A Biomimetic Insect-Sized Wing For Micro Air Vehicles, Jose Enrique Rubio

University of New Orleans Theses and Dissertations

The exceptional flying characteristics of airborne insects motivates the design of biomimetic wing structures that can exhibit a similar structural dynamic behavior. For this purpose, this investigation describes a method for both manufacturing a biomimetic insect-sized wing using the photolithography technique and analyzing its structural dynamic response. The geometry of a crane fly forewing (family Tipulidae) is acquired using a micro-computed tomography scanner. A computer-aided design model is generated from the measurements of the reconstructed scanned model of the insect wing to design the photomasks of the membrane and the venation network required for the photolithography procedure. A composite …

Highly Vented Truss Wall Honeycomb Structures, David J. Sypeck

Publications

A vented honeycomb structure with a plurality of honey­comb cells arranged in a hierarchical order and having a plurality of truss walls, each truss wall including a plurality of members. The vented honeycomb structure is fabricated by joining a plurality of sheets of trusses using any one of an expansion, a corrugation, and a slotting process. Fabri­cation can also occur by deposition, casting, additive, extru­sion, or aligning and joining methods. The honeycomb cells, truss walls, truss wall openings, and truss wall members can be functionally graded.

Highly Vented Truss Wall Honeycomb Structures, David J. Sypeck

Publications

A vented honeycomb structure with a plurality of honey­comb cells arranged in a hierarchical order and having a plurality of truss walls, each truss wall including a plurality of members. The vented honeycomb structure is fabricated by joining a plurality of sheets of trusses using any one of an expansion, a corrugation, and a slotting process. Fabri­cation can also occur by deposition, casting, additive, extru­sion, or aligning and joining methods. The honeycomb cells, truss walls, truss wall openings, and truss wall members can be functionally graded.

Outer Space: A Steam Voyage, Jancy Mcphee

The STEAM Journal

SciArt Exchange offers multi-disciplinary art contests, artwork events, consulting, training and community resources to support science and technology education, collaboration, and innovation. Using a science-integrated- with-art approach, SciArt Exchange supports, prepares, and convenes people of all ages, backgrounds and affiliations to discuss and potentially solve space, science, and technology challenges. This field note shares the Humans in Space Art Program and the Project Mars Competition.

Assessment Of Dynamic Effect Of Transmission Line Conductor Longitudinal Reaction Due To Downburst Loading, Ibrahim Ibrahim

Electronic Thesis and Dissertation Repository

Due to the locality and non-stationary nature of downburst wind loading events, their effect on the structural response of transmission line structures is of special nature that differs from conventional atmospheric boundary layer wind loading. Acknowledging such difference, the current thesis aims to quantify the dynamic effect associated with downburst loading on transmission line systems. To achieve that, several steps had to be realized, including experimentally verifying the numerical model used for analysis using wind field that was generated using computational fluid dynamics. The verified model was extended from model scale to full scale, where the wind field used for …

A Comparison Of The Aerodynamic Centers For Panel Code Compressible Corrections And Openfoam 5 For Mach 0.1 To 0.8, Dustin Weaver

All Graduate Plan B and other Reports, Spring 1920 to Spring 2023

It is known that the aerodynamic center changes from quarter chord to half chord from incompressible to compressible flows on airfoils. Compressible corrections are derived and implemented in a vortex panel code. These results will be used to find the aerodynamic centers for the specified Mach range of 0.1 to 0.8 in 0.1 increments within - 6 to 6 degrees angle of attack. OpenFOAM 5 cases will be created with specific meshes and settings. The results calculated from OpenFOAM 5 will be compared to the results obtained from the compressible corrections.

Multiphase Flow Modeling For Design And Optimization Of A Novel Down-Flow Bubble Column, Mutharasu Lalitha Chockalingam

LSU Doctoral Dissertations

The application of the Euler-Euler framework based Computational Fluid Dynamics (CFD) models for simulating the two-phase gas-liquid bubbly flow in down-flow bubble columns is discussed in detail. Emphasis is given towards the modelling and design optimization of a novel down-flow bubble column. The design features of this novel down-flow bubble column and its advantages over a conventional Plunging Jet down-flow bubble column are discussed briefly. Then, some of the present challenges in simulating a conventional Plunging Jet down-flow bubble column in the Euler-Euler framework is highlighted, and a sigmoid function based drag modification function is implemented to overcome those challenges. …

Real Time And High Fidelity Quadcopter Tracking System, Tyler Mckay Hall

Computer Engineering

This project was conceived as a desired to have an affordable, flexible and physically compact tracking system for high accuracy spatial and orientation tracking. Specifically, this implementation is focused on providing a low cost motion capture system for future research. It is a tool to enable the further creation of systems that would require the use of accurate placement of landing pads, payload acquires and delivery. This system will provide the quadcopter platform a coordinate system that can be used in addition to GPS.

Field research with quadcopter manufacturers, photographers, agriculture and research organizations were contact and interviewed for information …

Experimental Study Of Global Luminescent Oil-Film (Glof) Skin-Friction Meter On Delta Wings, Patrick Nicholas Wewengkang

Masters Theses

This thesis describes how the Global Luminescent Oil-Film (GLOF) Skin-Friction Meter can be applied experimentally to extract skin-friction from a set of images. In this study, the effect of oil viscosity, experimental sample size, and step size were considered to see how they would affect the extracted skin-friction using the GLOF method. These results were then compared to published literature on skin-friction diagnostics of delta wings, based on observations of critical characteristics such as reattachment and separation lines. Delta wings of 50°, 55°, 60°, 65°, and 70° sweep angles were built and placed in the Small Wind Tunnel (SWT) at …

Implementation And Verification Of A Synthetic Eddy Method (Sem) In The Eagle3d Compressible Flow Solver, Patrick Kopper

Doctoral Dissertations and Master's Theses

The objective of this thesis is to implement and evaluate a Synthetic Eddy Method (SEM) into the Eagle3D compressible ow solver. Both the ability of Eagle3D to resolve unsteady turbulent ow field and capability of the SEM to reproduce given Reynolds stress profiles to start realistic turbulent behavior are verified using common academic cases. Eagle3D is a Computational Fluid Dynamics (CFD) solver using a novel combination of a Bounded Central Differencing (BCD) scheme with Weighted Essentially Non-Oscillatory (WENO) approximation to reduce numerical dissipation. SEM is a modern synthetic turbulence method able to reproduce an arbitrary Reynolds stresses specification on discretionary …

A Study On The Control, Dynamics, And Hardware Of Micro Aerial Biomimetic Flapping Wing Vehicles, Siara Hunt

Doctoral Dissertations and Master's Theses

Biological flight encapsulates 400 million years of evolutionary ingenuity and thus is the most efficient way to fly. If an engineering pursuit is not adhering to biomimetic inspiration, then it is probably not the most efficient design. An aircraft that is inspired by bird or other biological modes of flight is called an ornithopter and is the original design of the first airplanes. Flapping wings hold much engineering promise with the potential to produce lift and thrust simultaneously. In this research, modeling and simulation of a flapping wing vehicle is generated. The purpose of this research is to develop a …

Model Predictive Power Management Of A Hybrid Electric Propulsion System For Aircraft, Tyler J. Wall

Masters Theses

This work presents the switched optimal power flow control for an aircraft with a hybrid electric propulsion system. The propulsion system is a switched system that operates in either of two modes: (i) battery discharging and electric motor propelling and (ii) battery charging and electric motor generating. The aircraft model and components that form the hybrid propulsion system are modeled as either an algebraic power source/sink or as a dynamic model with appropriate power and state interconnections. With the system model defined, a model predictive control power management strategy is set fourth which minimizes a performance index that includes altitude …

Aerodynamic Analysis Of Low Speed Wing Design Using Taguchi L9 Orthogonal Array, Kenneth Witcher, Ian Mcandrew, Elena Vishnevskaya

Publications

The study of aerodynamics has been preoccupied with understanding flight at increasing speeds and ultimately supersonic. Today, this pursuit has advanced the science for both Hypersonic and Transonic flight to near Mach 1 supporting economical commercial flight operations. This research presents the data from a Taguchi array on low speed with twin wing designs to establish the design parameters for their use in low speed and high altitude. Also presented is how aerodynamic advantages can be achieved through understanding the interactions of parameters and their use. This is compared to operational effectiveness when applied to remotely piloted aircraft that are …

Sensitivity Of Facial Organs Of Pythons As Deduced By Radiation Heat Transfer Analysis Under Varying Environmental Conditions, Rama Wairagkar

Theses and Dissertations

Predicting the behavior of snakes has been an interest to several scientists for the last few decades. Even though considerable amount of research has been carried out pertaining to snakes, there remains a degree of curiosity regarding their striking ability, live prey detection at locations where visual clues are unobtainable, thermosensation and the phenomena that drives these conducts. Researches carried out so far have moderately disregarded the perception of sensitivity of facial pits of snakes and its characteristics under contrasting temperature domains. This thesis attempts to undertake a computational analysis of the sensitivity of facial pits of Burmese pythons under …

Flight Dynamics: Flying Qualities Of Handling Factors Are Engineered Into The Aircraft Design, Nihad E. Daidzic

Aviation Department Publications

Flight dynamics is an aerospace engineering discupline that addresses aircraft stability and controllability. It is also mathematically very intensive and is traditionally the most difficult in the pilot training curriculum. Ultimately, it does not matter how good steady-state performance of an aircraft design is if its flying (handling) qualities are deficient. Paradoxically, the first airplane Wright Flyer, was statically and dynamically unstable, had large control authority, and was difficult to fly. We've come a long way since those early days, but stability is still vitally important in aircraft design and flight ops. The focus of this article will be airplane …

Mechanical And Electrical Characterization Of Carbon Fiber/Bucky Paper/Zinc Oxide Hybrid Composites, Suma Ayyagari

Doctoral Dissertations and Master's Theses

The quest for multifunctional carbon fiber reinforced composites (CFRPs) expedited the use of several nano reinforcements such as zinc oxide nanorods (ZnO) and carbon nanotubes (CNTs). Zinc oxide is semi-conductor with good piezoelectric and pyroelectric properties. These properties could be transmitted to CFRPs when a nanophase of ZnO is embedded within CFRPs. In lieu of ZnO nanorods, Bucky paper comprising mat of multiwall-carbon nanotubes (MWCNTs) could be sandwiched in-between laminae to construct a functionally graded composite with elevated electrical and thermal conductivities. In this study, a low temperature ( 90_C) hydrothermal synthesis method was utilized to grow ZnO nanorods on …

Low-Cost Wearable Head-Up Display For Flight General Aviation, Pavan K. Chinta

Doctoral Dissertations and Master's Theses

A low-cost wearable Commercial-off-The-Shelf (COTS) Augmented Reality (AR) Head-Up Display (HUD) system is designed, successfully reduced to practice, and flight tested. The system is developed based on the need for a technology that improves loss-of-control (LOC) safety in the General Aviation (GA) sector. The accuracy of the flight-path based system is determined to be within a degree of the truth source. The repeatability of the data from the COTS system is excellent. A complementary filter is proposed for air data flow angles and successfully flight tested for straight and level flight, dynamic maneuvering, and atmospheric turbulence, provided that a reasonably …

Aviation Propulsive Lithium-Ion Battery Packs State-Of-Charge And State-Of-Health Estimations And Propulsive Battery System Weight Analysis, Jingsi Lilly

Doctoral Dissertations and Master's Theses

Aviation propulsive battery pack research is in high demand with the development of electric and hybrid aircraft. Accurate inflight state-of-charge and state-of-health estimations of aviation battery packs still remain challenging. This thesis puts efforts on estimating the state-of-charge, state-of-health, and remaining energy of a lithium- ion propulsive battery pack with a recursive least squares based adaptive estimator. By reading the system measurements (discharging currents and terminal voltages) with persistent excitation, the proposed estimator can determine the present internal parameters of the battery cells and further interpolate them into state-of-charge, state-of-health, and the remaining energy information. The validation results indicate that …

Development Of A Remotely-Piloted Vehicle Platform To Support Implementation, Verification, And Validation Of Pilot Control Systems, Sean O’Toole

Doctoral Dissertations and Master's Theses

This thesis presents the development of a research test bed and the use of a set of metrics for evaluating handling qualities with pilot in the loop configuration. The main objective of this study is to provide software and hardware tools to support performance evaluation of control systems designed to compensate for Pilot Induced Oscillations (PIOs). A remotely-piloted vehicle presented in this thesis consists of an RC aircraft modified to be flown from a ground station cockpit. The unmanned aerial system has a high-speed on-board processing system capable of simulating different conditions during flight such as injecting actuator failures and …

Flight Testing Angle-Of-Attack Warning Combinations On Part 23 Aircraft, Jennifer Grey Geehan

Theses and Dissertations

The high number of accidents involving General Aviation (GA) aircraft leads to a need for improved methods to warn pilots of high angles of attack (AOA) and impending stall. Such methods must be certified by the Federal Aviation Administration (FAA) under Federal Aviation Regulations Part 23 regarding their effectiveness in preventing departures from controlled flight. Therefore, methods of compliance must be developed to certify Part 23 aircraft equipped with AOA warning or limiting systems. The research objectives were to (a) determine methods for the evaluation of AOA warning and limiting systems and to (b) evaluate the effectiveness of baseline combinations …

Coorstek- Spine Discectomy, Rhett Prestwich, Logan Bolingbroke, Ryan Thomsen, Aaron Blanchard, Kayla Park

Undergraduate Honors Capstone Projects

The objective is to design improved instrumentation for performing a spine discectomy. In particular, the instrument should remove the nucleus pulposus without damaging the annulus in order to prepare the spine disc for the insertion of an artificial spacer. As more nucleus pulposus is removed from the disc, the spine will fuse more quickly and completely after the artificial spacer is inserted. The current process involves removing the nucleus pulposus piece by piece with pituitary rongeurs. This process is slow and often incomplete.

System Study Of An On-Orbit Additive Manufacturing Cubesat, Juliette Isabelle Bido

Theses and Dissertations

The AddCube mission aims to demonstrate additive manufacturing technology in microgravity on a CubeSat platform by 3D-printing a 1-meter long rectangular beam on orbit. To accomplish this task, Made In Space Inc. (MIS) will provide the Extended Structure Additive Manufacturing Machine – CubeSat (ESAMM-C) payload. The high power required by the ESAMM-C payload creates a complex thermal problem within the spacecraft due to tight volume constraints associated with CubeSats. To cope with this problem, an in depth worst-case thermal analysis of the integrated spacecraft is conducted and an appropriate thermal management system for the mission is designed. Temperature regulation is …

Electron Yield Measurements Of High-Yield, Low-Conductivity Dielectric Materials, Justin Christensen

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Materials exposed to the space plasma environment acquire electric charge, which can have harmful effects if it leads to arcing or electrostatic breakdown of important spacecraft components. In fact, spacecraft charging is the leading environmentally induced cause of spacecraft anomalies. This study focuses on measuring electron yield, a property of materials that describes how many electrons are ejected from a material under energetic electron bombardment, which can vary depending on the energy of incident electrons. Intrinsic electron yield is defined as the average number of electrons emitted per incident electron from an electrically neutral material. The specific aim of this …

Manufacturing And Instrumentation Of An Open End Compressed Air Shock Tube, Josue O. Ruiz

Master's Theses

Shock tubes have been used extensively to study shock wave structures and high speed flow features. The purpose of constructing this open end shock tube was to have the ability to produce shock waves in a laboratory setting but also understand the exit flow coming out which can be applied to future studies that are beyond the scope of this work. This undertaking would require that an open end shock tube be built and instrumented with PCB Integrated Circuit Piezoelectric (ICP) Pressure Sensor Model 113B24 that would then be connected to a PCB Model 482C05 Signal Conditioner with the purpose …

A Comparison Study Of Composite Laminated Plates With Holes Under Tension, Joun S. Kim

Master's Theses

A Comparison Study of Composite Laminated Plates with Holes under Tension

A study was conducted to quantify the accuracy of numerical approximations to deem sufficiency in validating structural composite design, thus minimizing, or even eliminating the need for experimental test. Error values for stress and strain were compared between Finite Element Analysis (FEA) and analytical (Classical Laminated Plate Theory), and FEA and experimental tensile test for two composite plate designs under tension: a cross-ply composite plate design of [(0/90)4]s, and a quasi-isotropic layup design of [02/+45/-45/902]s, each with a single, centered hole of 1/8” diameter, and 1/4" diameter (four sets …

The Influence Of Varying Fiber Stacking Sequence On The Tensile, Impact, And Water Absorption Properties Of Unidirectional Flax/E-Glass Fiber Reinforced Epoxy Composite, Mohammed F. Al-Edhari

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

This thesis includes the study of the mechanical performance of two different types of fibers reinforced hybrid composites. Two kinds of fibers, natural fiber (flax) and synthetic fiber (E-glass), are used to reinforce epoxy resin. To evaluate the effective properties of the hybrid composites, a micromechanical analysis of the structure genome (SG) of a unidirectional fiber hybrid composites is performed using nite element analysis (FEA). Both fibers are assumed to be circular and packed in a hexagonal pattern. The effects of varying volume fractions and fiber locations, of the two fibers, on the elastic properties of the hybrid composites are …

Whitespace Exploration, Jason Lloyd Daniel

Master's Theses

As engineering systems grow in complexity so too must the design tools that we use evolve and allow for decision makers to efficiently ask questions of their model and obtain meaningful answers. The process of whitespace exploration has recently been developed to aid in engineering design and provide insight into a design space where traditional design exploration methods may fail. In an effort to further the research and development of whitespace exploration algorithms, a software package called Thalia has been created to allow for automated data collection and experimentation with the whitespace exploration methodology.

In this work, whitespace exploration is …

Development Of A Multi-Jointed Wing Surface Mover, Collin Arthur Strassburger

Masters Theses

The field of ornithopter research has reached a point where it has become commonplace for Computational Fluid Dynamics (CFD) solvers to have built-in capabilities for rigid solid body motion. This is suitable for micro air vehicles (MAVs) yet is often not exible enough to model wings with dynamic internal structure, such as the wings of birds and bats. There is currently no program available to perform the surface motion of a wing which has multiple independently moving joints. The code, detailed in this paper, provides the user with this type of capability. The bone lengths, joint angle properties, and thickening …