Open Access. Powered by Scholars. Published by Universities.®
- Keyword
-
- 3-D printing (5)
- Distributed manufacturing (3)
- 3D printing (2)
- Additive manufacturing (2)
- Consumer (2)
-
- Economics (2)
- Open hardware (2)
- Open-source (2)
- RepRap (2)
- 2-D reconstruction (1)
- Chemical mixing (1)
- Composite (1)
- Computer analysis (1)
- Custom designs (1)
- Customization (1)
- EPBT (1)
- Energy payback time (1)
- Error detection (1)
- Flexible materials (1)
- Free and open source software (1)
- Life cycle analysis (1)
- Manufacturing (1)
- Mixing (1)
- Nutating mixer (1)
- Open design (1)
- Open source (1)
- Open source hardware (1)
- OpenSCAD (1)
- Photovoltaic (1)
- Polymer filament (1)
Articles 1 - 7 of 7
Full-Text Articles in Engineering
Distributed Manufacturing Of Flexible Products: Technical Feasibility And Economic Viability, Aubrey Woern, Joshua M. Pearce
Distributed Manufacturing Of Flexible Products: Technical Feasibility And Economic Viability, Aubrey Woern, Joshua M. Pearce
Department of Materials Science and Engineering Publications
Distributed manufacturing even at the household level is now well established with the combined use of open source designs and self-replicating rapid prototyper (RepRap) 3-D printers. Previous work has shown substantial economic consumer benefits for producing their own polymer products. Now flexible filaments are available at roughly 3-times the cost of more conventional 3-D printing materials. To provide some insight into the potential for flexible filament to be both technically feasible and economically viable for distributed digital manufacturing at the consumer level this study investigates 20 common flexible household products. The 3-D printed products were quantified by print time, electrical …
Open Source 3-D Printed Nutating Mixer, Dhwani K. Trivedi, Joshua M. Pearce
Open Source 3-D Printed Nutating Mixer, Dhwani K. Trivedi, Joshua M. Pearce
Department of Materials Science and Engineering Publications
As the open source development of additive manufacturing has led to low-cost desktop three-dimensional (3-D) printing, a number of scientists throughout the world have begun to share digital designs of free and open source scientific hardware. Open source scientific hardware enables custom experimentation, laboratory control, rapid upgrading, transparent maintenance, and lower costs in general. To aid in this trend, this study describes the development, design, assembly, and operation of a 3-D printable open source desktop nutating mixer, which provides a fixed 20° platform tilt angle for a gentle three-dimensional (gyrating) agitation of chemical or biological samples (e.g., DNA or blood …
Impact Of Diy Home Manufacturing With 3d Printing On The Toy And Game Market, Emily Peterson, Joshua M. Pearce
Impact Of Diy Home Manufacturing With 3d Printing On The Toy And Game Market, Emily Peterson, Joshua M. Pearce
Department of Materials Science and Engineering Publications
The 2020 toy and game market is projected to be US$135 billion. To determine if 3D printing could affect these markets if consumers offset purchases by 3D printing free designs, this study investigates the 100 most popular downloaded designs at MyMiniFactory in a month. Savings are quantified for using a Lulzbot Mini 3D printer and three filament types: commercial filament, pellet-extruded filament, and post-consumer waste converted to filament with a recyclebot. Case studies probed the quality of: (1) six common complex toys; (2) Lego blocks; and (3) the customizability of open source board games. All filaments analyzed saved the user …
Three Hundred And Sixty Degree Real-Time Monitoring Of 3-D Printing Using Computer Analysis Of Two Camera Views, Siranee Nuchitprasitchai, Michael C. Roggemann, Joshua M. Pearce
Three Hundred And Sixty Degree Real-Time Monitoring Of 3-D Printing Using Computer Analysis Of Two Camera Views, Siranee Nuchitprasitchai, Michael C. Roggemann, Joshua M. Pearce
Department of Materials Science and Engineering Publications
Prosumer (producing consumer)-based desktop additive manufacturing has been enabled by the recent radical reduction in 3-D printer capital costs created by the open-source release of the self-replicating rapid prototype (RepRap). To continue this success, there have been some efforts to improve reliability, which are either too expensive or lacked automation. A promising method to improve reliability is to use computer vision, although the success rates are still too low for widespread use. To overcome these challenges an open source low-cost reliable real-time optimal monitoring platform for 3-D printing from double cameras is presented here. This error detection system is implemented …
Free And Open Source 3-D Model Customizer For Websites To Democratize Design With Openscad, Yuenyong Nilsiam, Joshua M. Pearce
Free And Open Source 3-D Model Customizer For Websites To Democratize Design With Openscad, Yuenyong Nilsiam, Joshua M. Pearce
Department of Materials Science and Engineering Publications
3-D printing has entered the consumer market because of recent radical price declines. Consumers can save substantial money by offsetting purchases with DIY pre-designed 3-D printed products. However, even more value can be obtained with distributed manufacturing using mass customization. Unfortunately, the average consumer is not technically sophisticated enough to easily design their own products. One solution to this is the use of an overlay on OpenSCAD parametric code, although current solutions force users to relinquish all rights to their own designs. There is thus a substantial need in the open source design community for a libre 3-D model customizer, …
Energy Payback Time Of A Solar Photovoltaic Powered Waste Plastic Recyclebot System, Shan Zhong, Pratiksha Rakhe, Joshua M. Pearce
Energy Payback Time Of A Solar Photovoltaic Powered Waste Plastic Recyclebot System, Shan Zhong, Pratiksha Rakhe, Joshua M. Pearce
Department of Materials Science and Engineering Publications
The growth of both plastic consumption and prosumer 3-D printing are driving an interest in producing 3-D printer filaments from waste plastic. This study quantifies the embodied energy of a vertical DC solar photovoltaic (PV) powered recyclebot based on life cycle energy analysis and compares it to horizontal AC recyclebots, conventional recycling, and the production of a virgin 3-D printer filament. The energy payback time (EPBT) is calculated using the embodied energy of the materials making up the recyclebot itself and is found to be about five days for the extrusion of a poly lactic acid (PLA) filament or 2.5 …
Open Source Multi-Head 3d Printer For Polymer-Metal Composite Component Manufacturing, J. Laureto, Joshua M. Pearce
Open Source Multi-Head 3d Printer For Polymer-Metal Composite Component Manufacturing, J. Laureto, Joshua M. Pearce
Department of Materials Science and Engineering Publications
As low-cost desktop 3D printing is now dominated by free and open source self-replicating rapid prototype (RepRap) derivatives, there is an intense interest in extending the scope of potential applications to manufacturing. This study describes a manufacturing technology that enables a constrained set of polymer-metal composite components. This paper provides (1) free and open source hardware and (2) software for printing systems that achieves metal wire embedment into a polymer matrix 3D-printed part via a novel weaving and wrapping method using (3) OpenSCAD and parametric coding for customized g-code commands. Composite parts are evaluated from the technical viability of manufacturing …