Open Access. Powered by Scholars. Published by Universities.®
Articles 1 - 8 of 8
Full-Text Articles in Engineering
Microstructural And Mechanical Behavior Investigations Of Nb-Reinforced Mg–Sn–Al–Zn–Mn Matrix Magnesium Composites, Ali Ercetin, Özgür Özgün, Kubilay Aslantaş, Oguzhan Der, Bekir Yalçın, Ercan Şimşir, Muhammad Aamir
Microstructural And Mechanical Behavior Investigations Of Nb-Reinforced Mg–Sn–Al–Zn–Mn Matrix Magnesium Composites, Ali Ercetin, Özgür Özgün, Kubilay Aslantaş, Oguzhan Der, Bekir Yalçın, Ercan Şimşir, Muhammad Aamir
Research outputs 2022 to 2026
This research focuses on the fabrication and characterization of TAZ532-xNb composites, employing high-purity, micron-sized powders of Mg, Sn, Al, Zn, Mn, and Nb as the raw materials. These powders were subjected to a paraffin coating process aimed at mitigating oxidation. The formation of composites was achieved via hot pressing and was followed by surface preparation and analysis using scanning electron microscopy (SEM) and energy-dispersive spectroscopy (EDS). An X-ray diffraction (XRD) study was conducted to identify the microstructural phases. Quantitative assessments including the theoretical density, actual density, and relative density were computed, and their fluctuations in relation to the increasing Nb …
Machining Of Carbon Steel Under Aqueous Environment: Investigations Into Some Performance Measures, Mushtaq Ali, Tahir Abdul Hussain Ratlamwala, Ghulam Hussain, Tauheed Shehbaz, Riaz Muhammad, Muhammad Aamir, Khaled Giasin, Danil Yurievich Pimenov
Machining Of Carbon Steel Under Aqueous Environment: Investigations Into Some Performance Measures, Mushtaq Ali, Tahir Abdul Hussain Ratlamwala, Ghulam Hussain, Tauheed Shehbaz, Riaz Muhammad, Muhammad Aamir, Khaled Giasin, Danil Yurievich Pimenov
Research outputs 2022 to 2026
In this study, a new machining approach (aqueous machining) is applied for mill machining and its performance is compared with traditional wet machining. AISI 1020 steel is employed as the test material and Taguchi statistical methodology is implemented to analyze and compare the performance of the two machining approaches. The cutting speed, feed rate, and depth of cut were the machining parameters used for both types of machining, while the selected response variables were surface roughness and hardness. Temperature variations were also recorded in aqueous machining. Compared with wet machining, aqueous machining resulted in lower surface roughness (up to 13 …
A New Method For Evaluating The Bond Strength Of Plasma-Sprayed Nicrbsi Coatings, Liang Yu Chen, Yi Tong Liu, Hao Nan Xuan, Cui Hua Zhao, Maksym Bobrov, Qian Hao Zang, Jin Hua Peng, Sheng Lu, Lai Chang Zhang
A New Method For Evaluating The Bond Strength Of Plasma-Sprayed Nicrbsi Coatings, Liang Yu Chen, Yi Tong Liu, Hao Nan Xuan, Cui Hua Zhao, Maksym Bobrov, Qian Hao Zang, Jin Hua Peng, Sheng Lu, Lai Chang Zhang
Research outputs 2022 to 2026
The bond strength is a critical consideration for the plasma-sprayed NiCrBSi coatings. However, the conventional methods for testing the bond strength of NiCrBSi coatings always cost time and money. If there is a simple method that could predict the bond strength of the prepared NiCrBSi coatings without destroying the coatings, it would be significantly beneficial for industrial applications. In this work, a new method was proposed based on the total areas of the interfacial pores for the NiCrBSi coatings. The NiCrBSi coating was prepared by plasma spraying technology and the as-sprayed coating was subsequently remelted by plasma arc using the …
Phase Transformation-Induced Improvement In Hardness And High-Temperature Wear Resistance Of Plasma-Sprayed And Remelted Nicrbsi/Wc Coatings, Jin Sha, Liang-Yu Chen, Yi-Tong Liu, Zeng-Jian Yao, Sheng Lu, Ze-Xin Wang, Qian-Hao Zang, Shu-Hua Mao, Lai-Chang Zhang
Phase Transformation-Induced Improvement In Hardness And High-Temperature Wear Resistance Of Plasma-Sprayed And Remelted Nicrbsi/Wc Coatings, Jin Sha, Liang-Yu Chen, Yi-Tong Liu, Zeng-Jian Yao, Sheng Lu, Ze-Xin Wang, Qian-Hao Zang, Shu-Hua Mao, Lai-Chang Zhang
Research outputs 2014 to 2021
© 2020 by the authors. Licensee MDPI, Basel, Switzerland. The remelting method is introduced to improve the properties of the as-sprayed NiCrBSi coatings. In this work, tungsten carbide (WC) was selected as reinforcement and the as-sprayed and remelted NiCrBSi/WC composite coatings were investigated by X-ray diffraction, scanning electron microscopy, hardness test and tribology test. After spraying, WC particles are evenly distributed in the coating. The remelting process induced the decarburizing reaction of WC, resulting in the formation of dispersed W2 C. The dispersed W2 C particles play an important role in the dispersion strengthening. Meanwhile, the pores and lamellar structures …
Particle Size-Dependent Microstructure, Hardness And Electrochemical Corrosion Behavior Of Atmospheric Plasma Sprayed Nicrbsi Coatings, Peng Sang, Liang-Yu Chen, Cuihua Zhao, Ze-Xin Wang, Haiyang Wang, Sheng Lu, Dongpo Song, Jia-Huan Xu, Lai-Chang Zhang
Particle Size-Dependent Microstructure, Hardness And Electrochemical Corrosion Behavior Of Atmospheric Plasma Sprayed Nicrbsi Coatings, Peng Sang, Liang-Yu Chen, Cuihua Zhao, Ze-Xin Wang, Haiyang Wang, Sheng Lu, Dongpo Song, Jia-Huan Xu, Lai-Chang Zhang
Research outputs 2014 to 2021
Particle size is a critical consideration for many powder coating-related industries since it significantly influences the properties of the produced materials. However, the effect of particle size on the characteristics of plasma sprayed NiCrBSi coatings is not well understood. This work investigates the microstructures, hardness and electrochemical corrosion behavior of plasma sprayed NiCrBSi coatings synthesized using different-sized powders. All coatings mainly consist of Ni, N3B, CrB, Cr7C3 and Cr3C2 phases. The coatings produced by small particles (50–75 μm) exhibit lower porosity (2.0 ± 0.8%). Such coatings show a higher fraction (15.5 vol.%) of the amorphous phase and lower hardness (700 …
Beta-Type Ti-Nb-Zr-Cr Alloys With Large Plasticity And Significant Strain Hardening, Syed F. Jawed, Chirag D. Rabadia, Y. J. Liu, L. Q. Wang, Y. H. Li, X. H. Zang, Laichang C. Zhang
Beta-Type Ti-Nb-Zr-Cr Alloys With Large Plasticity And Significant Strain Hardening, Syed F. Jawed, Chirag D. Rabadia, Y. J. Liu, L. Q. Wang, Y. H. Li, X. H. Zang, Laichang C. Zhang
Research outputs 2014 to 2021
A series of Ti-25Nb-8Zr-xCr (x = 0, 2, 4, 6, 8 wt%) alloys were designed based on DV-Xα cluster method and e=a-Δr diagram with an anticipation to obtain high plasticity and significant strain hardening. The designed alloys were produced through cold crucible levitation melting technique in order to effectively investigate their micro-structures and mechanical properties. The addition of Cr significantly enhances the β stability in the microstructures of the Ti-25Nb-8Zr-xCr alloys. Both yield strength and hardness of the studied alloys increase due to the effect of solid-solution strengthening. By contrast, the plasticity, maximum strength and strain hardening rate are influenced …
Nanoindentation Characterization On Local Plastic Response Of Ti-6al-4v Under High-Load Spherical Indentation, Yan Wen, Lechun Xie, Zhou Wang, Liqiang Wang, Weijie Lu, Laichang Zhang
Nanoindentation Characterization On Local Plastic Response Of Ti-6al-4v Under High-Load Spherical Indentation, Yan Wen, Lechun Xie, Zhou Wang, Liqiang Wang, Weijie Lu, Laichang Zhang
Research outputs 2014 to 2021
After high-load spherical indentation treatment, the variations of hardness on the plastic zone of Ti-6Al-4V were investigated via nanoindentation method. The hardness within the center of plastic zone was measured by nanoindenter, and the magnitude decreased gradually along the depth, which were caused by the different extent of plastic deformation under the residual imprint. The microstructure of indentation were observed using scanning electron microscope (SEM) before and after surface etching, and the results showed that the microhardness revealed the average hardness of α and β phases of Ti-6Al-4V. The maximum hardness reached 6.438 GPa in the depth of 132 μm. …
Synergistic Toughening Of Hard, Nacre-Mimetic Mosi2 Coatings By Self-Assembled Hierarchical Structure, Jiang Xu, Xiaoli Zhao, Paul Munroe, Zonghan Xie
Synergistic Toughening Of Hard, Nacre-Mimetic Mosi2 Coatings By Self-Assembled Hierarchical Structure, Jiang Xu, Xiaoli Zhao, Paul Munroe, Zonghan Xie
Research outputs 2014 to 2021
Like many other intermetallic materials, MoSi2 coatings are typically hard, but prone to catastrophic failure due to their low toughness at ambient temperature. In this paper, a self-assembled hierarchical structure that closely resembles that of nacre (i.e., mother of pearl) was developed in a MoSi2 -based coating through a simple, yet cost-effective, depostion technique. The newly formed coating is tough and can withstand multiple indentations at high loads. Key design features responsible for this remarkable outcome were identified. They include a functionally graded multilayer featuring elastic modulus oscillation, varying sublayer thickness and a columnar structure that are able to attenuate …