Engineering Commons^™

Free-Troposphere Ozone And Carbon Monoxide Over The North Atlantic For 2001-2011, Aditya Kumar, S. Wu, M. F. Weise, R. Honrath, R. C. Owen, D. Helmig, L. Kramer, M. Val Martin, Q. Li

Michigan Tech Publications

In situ measurements of carbon monoxide (CO) and ozone (O3) at the Pico Mountain Observatory (PMO) located in the Azores, Portugal, are analyzed together with results from an atmospheric chemical transport model (GEOS-Chem) and satellite remote sensing data (AIRS (Atmospheric Infrared Sounder) for CO, and TES (Tropospheric Emission Spectrometer) for O3) to examine the evolution of free-troposphere CO and O3 over the North Atlantic for 2001-2011. GEOS-Chem captured the seasonal cycles for CO and O3 well but significantly underestimated the mixing ratios of CO, particularly in spring. Statistically significant (using a significance level of 0.05) decreasing trends were found for …

Enhanced Dna Sensing Via Catalytic Aggregation Of Gold Nanoparticles, Herbert M. Huttanus, Elton Graugnard, Bernard Yurke, William B. Knowlton, Wan Kuang, William L. Hughes, Jeunghoon Lee

Materials Science and Engineering Faculty Publications and Presentations

A catalytic colorimetric detection scheme that incorporates a DNA-based hybridization chain reaction into gold nanoparticles was designed and tested. While direct aggregation forms an inter-particle linkagefrom only one target DNA strand, catalytic aggregation forms multiple linkages from a single target DNA strand. Gold nanoparticles were functionalized with thiol-modified DNA strands capable of undergoing hybridization chain reactions. The changes in their absorption spectra were measured at different times and target concentrations and compared against direct aggregation. Catalytic aggregation showed a multifold increase in sensitivity at low target concentrations when compared to direct aggregation. Gelelectrophoresis was performed to compare DNA hybridization reactions …

Nd-Fe-B Nanoparticles Through Surfactant Assisted Mechanical Milling And Alloy Design, Jordann M. Bornhoft

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Surfactant-assisted mechanical milling has been used to produce discrete nanoparticles of both Nd-Fe-B and Sm-Co amenable for bottom-up production of nanostructured or nanocomposite permanent magnets. However, in Nd-Fe-B the comminution of the material proceeds by transgranular fracture, which influences both the morphology of the nanoparticles and the magnetic properties. This paper utilizes alloy design to alter the fracture behavior from transgranular fracture to intergranular fracture. Nd-rich Nd₂Fe₁₄B alloys were produced by melt spinning in an overquenched state. The melt spun ribbons were annealed at 700°C and 800°C to ensure complete crystallization and to form different grain …

Unification Of The Negative Electrocaloric Effect In Bi1/2Na1/2Tio3-Batio3 Solid Solutions By Ba1/2Sr1/2Tio3 Doping, Sarir Uddin, Guang-Ping Zheng, Yaseen Iqbal, Rick Ubic, Junhe Yang

Materials Science and Engineering Faculty Publications and Presentations

The microscopic mechanisms of the negative electrocaloric effect (ECE) of the single-phase (1−x)(0.94Bi_1/2Na_1/2TiO₃-0.06BaTiO₃)-xBa_1/2Sr_1/2TiO₃ (BNT-BT-BST) perovskite solid solutions fabricated via the sol-gel technique are explored in this study. Dielectric and mechanical relaxation analyses are employed to investigate the ferroelectric and structural transitions of the samples. The electrocaloric properties of the samples were measured by thermodynamics Maxwell relations. The difference between the depolarization temperature (T_d) and the maximum dielectric constant temperature (T_m) was found to decrease with increasing BST content. Doping with BST stabilized the …

Kolsky Bar Experiment For High-Rate Large Deformations Of Polycarbonate, Jason Gerald Vogeler

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Polycarbonate (PC) is a tough, transparent engineering thermoplastic. Its impact strength and ability undergo large plastic deformations without shatter make PC an ideal protective material for impact-resilient eyewear, aircraft windows and transparent armor. A good understanding of the response of this material to large deformations at high strain rates is critical for its utilization in these applications. To this end, a striker-less Kolsky bar device is employed in this work for the needed material characterization. The apparatus allow impulsive torsion and/or compression loadings with pulse durations sufficiently long for the plastic flow behavior to develop fully. Three new testing techniques …

Kolsky Bar Experiment For High-Rate Large Deformations Of Polycarbonate, Jason G. Vogeler

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Polycarbonate (PC) is a tough, transparent engineering thermoplastic. Its impact strength and ability undergo large plastic deformations without shatter make PC an ideal protective material for impact-resilient eyewear, aircraft windows and transparent armor. A good understanding of the response of this material to large deformations at high strain rates is critical for its utilization in these applications. To this end, a striker-less Kolsky bar device is employed in this work for the needed material characterization. The apparatus allow impulsive torsion and/or compression loadings with pulse durations sufficiently long for the plastic flow behavior to develop fully. Three new testing techniques …

Ultrasonic Propagation And Scattering In Pearlitic Steel, Hualong Du

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Diffuse ultrasonic backscatter measurements have been especially useful for extracting microstructural information and for improving flaw detection in materials. In this dissertation, this approach is applied to inspection of railroad wheels. To improve the wear resistance, the tread surfaces of railroad wheels are usually quenched with water to increase the hardness. The pearlite phase of iron, characterized by alternating ferrite and cementite phases, is created by the quenching and the lamellar spacing within grains increases progressively from the quenched tread surface to deeper locations due to the non-uniform cooling rate. The quench depth is an important parameter governing the wheel …

In-Situ Study Of E-Beam Al And Hf Metal Deposition On Native Oxide Inp (100), H. Dong, Santosh Kc, A. Azcatl, W. Cabrera, X. Qin, B. Brennan, D. Zhernokletov, K. Cho, R. Wallace

Faculty Publications

The interfacial chemistry of thin Al (∼3 nm) and Hf (∼2 nm) metal films deposited by electron beam (e-beam) evaporation on native oxide InP (100) samples at room temperature and after annealing has been studied by in situ angle resolved X-ray photoelectron spectroscopy and low energy ion scattering spectroscopy. The In-oxides are completely scavenged forming In-In/In-(Al/Hf) bonding after Al and Hf metal deposition. The P-oxide concentration is significantly decreased, and the P-oxide chemical states have been changed to more P-rich oxides upon metal deposition. Indium diffusion through these metals before and after annealing at 250 °C has also been characterized. …

Investigation Of Thermal Cycle And Hardness Distribution In The Laser Cladding Of Aisi H13 Tool Steel Produced By A High Power Direct Diode Laser, Parisa Farahmand, Prabu Balu, Fanrong Kong, Radovan Kovacevic

Mechanical Engineering Research

Laser cladding (LC) of tool steel has significant application in rapid tooling, and surface coating for worn-out components in different industries. During the LC process, several phase transformations influence the microstructural and mechanical properties of the deposited layer. In order to successfully implement the LC process, it is essential to understand the relationship between the thermal cycle (heating and cooling), phase transformations, and the output quantities of the deposited layer. In this study a direct diode laser with a power of up to 8 kW was used to deposit AISI H13 tool steel on mild steel grade A36 substrate to …

Binding, Transcytosis And Biodistribution Of Anti-Pecam-1 Iron Oxide Nanoparticles For Brain-Targeted Delivery, Mo Dan, David B. Cochran, Robert A. Yokel, Thomas D. Dziubla

Pharmaceutical Sciences Faculty Publications

OBJECTIVE: Characterize the flux of platelet-endothelial cell adhesion molecule (PECAM-1) antibody-coated superparamagnetic iron oxide nanoparticles (IONPs) across the blood-brain barrier (BBB) and its biodistribution in vitro and in vivo.

METHODS: Anti-PECAM-1 IONPs and IgG IONPs were prepared and characterized in house. The binding affinity of these nanoparticles was investigated using human cortical microvascular endothelial cells (hCMEC/D3). Flux assays were performed using a hCMEC/D3 BBB model. To test their immunospecificity index and biodistribution, nanoparticles were given to Sprague Dawley rats by intra-carotid infusion. The capillary depletion method was used to elucidate their distribution between the BBB and brain parenchyma.

RESULTS: Anti-PECAM-1 …

Oil Droplet Behavior At A Pore Entrance In The Presence Of Crossflow: Implications For Microfiltration Of Oil-Water Dispersions, Nikolai V. Priezjev, Tohid Darvishzadeh, Volodymyr V. Taravara

Mechanical and Materials Engineering Faculty Publications

The behavior of an oil droplet pinned at the entrance of a micropore and subject to clossflow-induced shear is investigated numerically by solving the Navier-Stokes equation. We found that in the absence of crossflow, the critical transmembrane pressure required to force the droplet into the pore is in excellent agreement with a theoretical prediction based on the Young-Laplace equation. With increasing shear rate, the critical pressure of permeation increases, and at sufficiently high shear rates the oil droplet breaks up into two segments. The results of numerical simulations indicate that droplet breakup at the pore entrance is facilitated at lower …

Compounds And Methods For Reducing The Occurrence Of Post-Surgical Adhesions, Thomas Dziubla, Eugene Kaplan, John Mark Medley Jr.

Chemical and Materials Engineering Faculty Patents

Compounds and methods for reducing the occurrence of a post-surgical adhesion are provided. The compounds can include acrylic acid groups and ethylene glycol groups, and can be directed to an area of damaged tissue by the incorporation of a fibrin targeting peptide. The compounds can further include a brush-like portion, capable of creating a steric barrier between a damaged tissue or organ and adjacent tissues or organs, and a targeting portion, capable of directing the compounds to a damaged tissue or organ. Methods of detecting damaged tissue and kits are also provided.

Characterisation And Optimisation Of Magnetorheological Elastomers, Jennifer Mcintyre

Doctoral

The primary aim of this research was to optimise the design of magnetorheological elastomers (MREs), composite materials consisting of magnetic particles in an elastomer matrix. In doing so, the understanding of their dynamic behaviour when subjected to stress would be furthered. Plenty of uses have been suggested for these materials which adapt to their environments and can be tuned to suit operating conditions, but very few of these have actually been realised. Characterising their dynamic behaviour is crucial if they are to gain wider use in commercial applications. The first objective of the research was to investigate the factors affecting …

Physiological Fluid Specific Agglomeration Patterns Diminish Gold Nanorod Photothermal Characteristics, Kristen K. Comfort, Jared W. Speltz, Bradley M. Stacy, Larry R. Dosser, Saber M. Hussain

Chemical and Materials Engineering Faculty Publications

Investigations into the use of gold nanorods (Au-NRs) for biological applications are growing exponentially due to their distinctive physicochemical properties, which make them advantageous over other nanomaterials. Au-NRs are particularly renowned for their plasmonic characteristics, which generate a robust photothermal response when stimulated with light at a wavelength matching their surface plasmon resonance. Numerous reports have explored this nanophotonic phenomenon for temperature driven therapies; however, to date there is a significant knowledge gap pertaining to the kinetic heating profile of Au-NRs within a controlled physiological setting. In the present study, the impact of environmental composition on Au-NR behavior and degree …

A Systematic Study Of Radiation-Induced Segregation In Ferritic–Martensitic Alloys, Janelle P. Wharry, Gary S. Was

Materials Science and Engineering Faculty Publications and Presentations

A systematic approach to measuring radiation-induced segregation (RIS) was used on four ferritic–martensitic (F–M) alloys: T91, HCM12A, HT9, and a Fe–9Cr model alloy, irradiated with 2.0 MeV protons over a range of doses (1–10 dpa) and temperatures (300–700°C). The experimental conditions are established so as to isolate the dependence of RIS on the experimental parameters: temperature, dose and bulk composition. RIS is measured at prior austenite grain boundaries (PAGBs) using the STEM/EDX technique. Chromium is found to enrich at PAGBs in all conditions with the exception being T91 irradiated to 3 dpa at 700°C. The magnitude of enrichment is small …

Magnetic Interaction Reversal In Watermelon Nanostructured Cr-Doped Fe Nanoclusters, Maninder Kaur, Qilin Dai, Mark Bowden, Mark H. Engelhard, Yaqiao Wu, Jinke Tang, You Qiang

Materials Science and Engineering Faculty Publications and Presentations

Cr-doped core-shell Fe/Fe-oxide nanoclusters (NCs) were synthesized at varied atomic percentages of Cr from 0 at. % to 8 at. %. The low concentrations of Cr (%) were selected in order to inhibit the complete conversion of the Fe-oxide shell to Cr₂O₃ and the Fe core to FeCr alloy. The magnetic interaction in Fe/Fe-oxide NCs (~25 nm) can be controlled by antiferromagnetic Cr-dopant. We report the origin of σ-FeCr phase at very low Cr concentration (2 at. %) unlike in previous studies, and the interaction reversal from dipolar to exchange interaction in watermelon-like Cr-doped core-shell NCs.

A Clamped Dual-Ridged Waveguide Measurement System For The Broadband, Nondestructive Characterization Of Sheet Materials, Milo W. Hyde Iv, Michael J. Havrilla

Faculty Publications

A novel two-port probe which uses dual-ridged waveguides for the nondestructive, broadband characterization of sheet materials is presented. The new probe is shown to possess approximately 2 to 3 times the bandwidth of traditional coaxial and rectangular/circular waveguide probe systems while maintaining the structural robustness characteristic of rectangular/circular waveguide probe systems. The theoretical development of the probe is presented, namely, by applying Love’s equivalence theorem and enforcing the continuity of transverse fields at the dual-ridged waveguide apertures, a system of coupled magnetic field integral equations is derived. The system of coupled magnetic field integral equations is solved using the method …

In Situ Study Of The Role Of Substrate Temperature During Atomic Layer Deposition Of Hfo2 On Inp, H. Dong, Santosh Kc, X. Qin, B. Brennan, S. Mcdonnell, D. Zhernokletov, C. Hinkle, J. Kim, K. Cho, R. Wallace

Faculty Publications

The dependence of the “self cleaning” effect of the substrate oxides on substrate temperature during atomic layer deposition (ALD) of HfO2 on various chemically treated and native oxide InP (100) substrates is investigated using in situ X-ray photoelectron spectroscopy. The removal of In-oxide is found to be more efficient at higher ALD temperatures. The P oxidation states on native oxide and acid etched samples are seen to change, with the total P-oxide concentration remaining constant, after 10 cycles of ALD HfO2 at different temperatures. An (NH4)2 S treatment is seen to effectively remove native oxides and passivate the InP surfaces …

High Field Breakdown Characteristics Of Carbon Nanotube Thin Film Transistors, Man Prakash Gupta, Ashkan Behnam, Feifei Lian, David Estrada, Eric Pop, Satish Kumar

Materials Science and Engineering Faculty Publications and Presentations

The high field properties of carbon nanotube (CNT) network thin film transistors (CN-TFTs) are important for their practical operation, and for understanding their reliability. Using a combination of experimental and computational techniques we show how the channel geometry (length L_C and width W_C) and network morphology (average CNT length L_t and alignment angle distribution θ) affect heat dissipation and high field breakdown in such devices. The results suggest that when W_C ≥ L_t, the breakdown voltage remains independent of W_C but varies linearly with L_C. The breakdown power varies …

Zno Nanoneedle/H2o Solid-Liquid Heterojunction-Based Self-Powered Ultraviolet Detector, Qinghao Li, Lin Wei, Yanru Xie, Kai Zhang, Lei Liu, Dapeng Zhu, Jun Jiao, Yanxue Chen, Shishen Yan, Guolei Liu, Liangmo Mei

Physics Faculty Publications and Presentations

ZnO nanoneedle arrays were grown vertically on a fluorine-doped tin oxide-coated glass by hydrothermal method at a relatively low temperature. A self-powered photoelectrochemical cell-type UV detector was fabricated using the ZnO nanoneedles as the active photoanode and H2O as the electrolyte. This solid-liquid heterojunction offers an enlarged ZnO/water contact area and a direct pathway for electron transport simultaneously. By connecting this UV photodetector to an ammeter, the intensity of UV light can be quantified using the output short-circuit photocurrent without a power source. High photosensitivity, excellent spectral selectivity, and fast photoresponse at zero bias are observed in this UV detector. …

A Tensile Deformation Model For In-Situ Dendrite/Metallic Glass Matrix Composites, J. W. Qiao, T. Zhang, Fuqian Yang, P. K. Liaw, S. Pauly, B. S. Xu

Chemical and Materials Engineering Faculty Publications

In-situ dendrite/metallic glass matrix composites (MGMCs) with a composition of Ti₄₆Zr₂₀V₁₂Cu₅Be₁₇ exhibit ultimate tensile strength of 1510 MPa and fracture strain of about 7.6%. A tensile deformation model is established, based on the five-stage classification: (1) elastic-elastic, (2) elastic-plastic, (3) plastic-plastic (yield platform), (4) plastic-plastic (work hardening), and (5) plastic-plastic (softening) stages, analogous to the tensile behavior of common carbon steels. The constitutive relations strongly elucidate the tensile deformation mechanism. In parallel, the simulation results by a finite-element method (FEM) are in good agreement with the experimental findings and theoretical calculations. The present study gives a mathematical model to clarify …

The Biological Impact Of Concurrent Exposure To Metallic Nanoparticles And A Static Magnetic Field, Kristen K. Comfort, Elizabeth I. Maurer, Saber M. Hussain

Chemical and Materials Engineering Faculty Publications

The rapid advancement of technology has led to an exponential increase of both nanomaterial and magnetic field utilization in applications spanning a variety of sectors. While extensive work has focused on the impact of these two variables on biological systems independently, the existence of any synergistic effects following concurrent exposure has yet to be investigated. This study sought to ascertain the induced alterations to the stress and proliferation responses of the human adult low calcium, high temperature keratinocyte (HaCaT) cell line by the application of a static magnetic field (approximately 0.5 or 30 mT) in conjunction with either gold or …

Clean Hydrogen Production And Carbon Dioxide Capture Methods, Sushant Kumar

FIU Electronic Theses and Dissertations

Fossil fuels constitute a significant fraction of the world’s energy demand. The burning of fossil fuels emits huge amounts of carbon dioxide into the atmosphere. Therefore, the limited availability of fossil fuel resources and the environmental impact of their use require a change to alternative energy sources or carriers (such as hydrogen) in the foreseeable future. The development of methods to mitigate carbon dioxide emission into the atmosphere is equally important. Hence, extensive research has been carried out on the development of cost-effective technologies for carbon dioxide capture and techniques to establish hydrogen economy.

Hydrogen is a clean energy fuel …

Capacitive Properties And Structure Of Ruo₂-Hfo₂ Films Prepared By Thermal Decomposition Method, Xuehua Liu, Junqiu Zhu, Xin Wang, Jinghua Sun, Zhongzhi Tang, Teng Zhang, Matthew O'Keefe, Dian Tang

Materials Science and Engineering Faculty Research & Creative Works

Binary RuO₂-HfO₂ films on Ti substrates were prepared by a thermal decomposition method. cyclic voltammetric and charge/discharge properties of the RuO₂-HfO₂ electrodes were characterized. It was determined that the incorporation of HfO₂ into RuO ₂ greatly improved the capacitive properties of the material. The RuO₂-HfO₂ electrodes showed excellent cyclic stability, with no decay in charge capability during 1000 CV cycles in acidic solution. A nominal content of 50 mol% RuO₂ and 50 mol% HfO₂ gave the highest specific capacitance of 789.3 F/g (RuO₂). The excellent capacitive …

On The Uniqueness And Sensitivity Of Indentation Testing Of Isotropic Materials, J. K. Phadikar, T. A. Bogetti, Anette M. Karlsson

Mechanical Engineering Faculty Publications

Instrumented indentation is a popular technique to extract the material properties of small scale structures. The uniqueness and sensitivity to experimental errors determine the practical usefulness of such experiments. Here, a method to identify test techniques that minimizes sensitivity to experimental erros is in indentation experiments developed. The methods are based on considering “shape functions,” which are sets of functions that describe the force–displacement relationship obtained during the indentation test. The concept of condition number is used to investigate the relative reliability of various possible dual indentation techniques. Interestingly, it was found that many dual indentation techniques can be as …

Enhanced Reducibility And Conductivity Of Na/K-Doped Srti0.8Nb0.2O3, Guoliang Xiao, Sirikanda Nuansaeng, Lei Zhang, Suwit Suthirakun, Andreas Heyden, Hans-Conrad Zur Loye, Fanglin Chen

Faculty Publications

Donor and acceptor co-doped SrTiO₃ materials have shown interesting features in their conductivity and reducibility. In this work, 10 mol% Na⁺ or K⁺ as acceptor dopants have been introduced into the A-site of donor-doped strontium titanate, SrTi_0.8Nb_0.2O₃, and the doping impact on their properties has been studied. By doping with Na or K, the sinterability of SrTi_0.8Nb_0.2O₃ in reducing atmospheres has been improved. Na_0.1Sr_0.9Ti_0.8Nb_0.2O₃ and K_0.1Sr_0.9Ti_0.8Nb_0.2O₃ show metallic …

Wound Care, Steven B. Jung, D. E. Day

Materials Science and Engineering Faculty Research & Creative Works

A method for treating a wound, and a dressing for wound care management comprising a three-dimensional body of glass-based fibers comprising one or more glass-formers selected from the group consisting of P₂O5, SiO₂, and B₂O₃; at least about 25 wt % of the fibers have a diameter between about 200 nm and about 4000 nm, and a length:width aspect ratio of at least about 10. In another form, the glasses are in the form of particles in an ointment or cream applied to a wound. In yet other forms the glasses are …

Quantum Computing Circuits, Cheng-Hsiao Wu, Casey Andrew Cain

Electrical and Computer Engineering Faculty Research & Creative Works

A system for performing digital operations, including a first device configured to transform a digital input into one or more signals, at least one AB ring, the at least one AB ring irreducibly-coupled and configured to include at least three terminals, a second device configured to read a portion of a signal expressed upon two or more of the at least three terminals, and a third device configured to transform the portion of the signal expressed upon two or more of the at least three terminals into a digital output, the third device operationally connected to the second device.

Metal-Assisted Etching Of Silicon Molds For Electroforming, Ralu Divan, Dan Rosenthal '14, Karim Ogando, Leonidas E. Ocola, Daniel Rosenmann, Nicolaie Moldovan

Student Publications & Research

Ordered arrays of high-aspect-ratio micro/nanostructures in semiconductors stirred a huge scientific interest due to their unique one-dimensional physical morphology and the associated electrical, mechanical, chemical, optoelectronic, and thermal properties. Metal-assisted chemical etching enables fabrication of such high aspect ratio Si nanostructures with controlled diameter, shape, length, and packing density, but suffers from structure deformation and shape inconsistency due to uncontrolled migration of noble metal structures during etching. Hereby the authors prove that a Ti adhesion layer helps in stabilizing gold structures, preventing their migration on the wafer surface while not impeding the etching. Based on this finding, the authors demonstrate …

Comment On "Giant Plasticity Of A Quantum Crystal", Caizhi Zhou, Charles J. Olson Reichhardt, Matthias J. Graf, Jungjung Su, Alexander V. Balatsky, Irene J. Beyerlein

Materials Science and Engineering Faculty Research & Creative Works

In their Letter, Haziot et al. report a novel phenomenon of giant plasticity for hcp ⁴He quantum crystals. They assert that ⁴He exhibits mechanical properties not found in classical plasticity theory. Specifically, they examine high-quality crystals as a function of temperature T and applied strain ϵ_app, where the shear modulus µ =T_app/ϵ_app reaches a plateau and dissipation 1=Q becomes close to zero; both quantities are reported to be independent of applied stress T_app and strain ϵ_app, implying a reversible dissipation process and suggesting dislocation motion by quantum tunneling. At lower …