Open Access. Powered by Scholars. Published by Universities.®
- Discipline
Articles 1 - 4 of 4
Full-Text Articles in Engineering
Particle Size-Dependent Microstructure, Hardness And Electrochemical Corrosion Behavior Of Atmospheric Plasma Sprayed Nicrbsi Coatings, Peng Sang, Liang-Yu Chen, Cuihua Zhao, Ze-Xin Wang, Haiyang Wang, Sheng Lu, Dongpo Song, Jia-Huan Xu, Lai-Chang Zhang
Particle Size-Dependent Microstructure, Hardness And Electrochemical Corrosion Behavior Of Atmospheric Plasma Sprayed Nicrbsi Coatings, Peng Sang, Liang-Yu Chen, Cuihua Zhao, Ze-Xin Wang, Haiyang Wang, Sheng Lu, Dongpo Song, Jia-Huan Xu, Lai-Chang Zhang
Research outputs 2014 to 2021
Particle size is a critical consideration for many powder coating-related industries since it significantly influences the properties of the produced materials. However, the effect of particle size on the characteristics of plasma sprayed NiCrBSi coatings is not well understood. This work investigates the microstructures, hardness and electrochemical corrosion behavior of plasma sprayed NiCrBSi coatings synthesized using different-sized powders. All coatings mainly consist of Ni, N3B, CrB, Cr7C3 and Cr3C2 phases. The coatings produced by small particles (50–75 μm) exhibit lower porosity (2.0 ± 0.8%). Such coatings show a higher fraction (15.5 vol.%) of the amorphous phase and lower hardness (700 …
Calculation Of Oxygen Diffusion Coefficients In Oxide Films Formed On Low-Temperature Annealed Zr Alloys And Their Related Corrosion Behavior, Lina Zhang, Liang-Yu Chen, Cuihua Zhao, Yujing Liu, Lai-Chang Zhang
Calculation Of Oxygen Diffusion Coefficients In Oxide Films Formed On Low-Temperature Annealed Zr Alloys And Their Related Corrosion Behavior, Lina Zhang, Liang-Yu Chen, Cuihua Zhao, Yujing Liu, Lai-Chang Zhang
Research outputs 2014 to 2021
The growth of oxide film, which results from the inward oxygen diffusion from a corrosive environment, is a critical consideration for the corrosion resistance of zirconium alloys. This work calculates the oxygen diffusion coefficients in the oxide films formed on zirconium alloys annealed at 400~500 °C and investigates the related corrosion behavior. The annealed samples have a close size for the second-phase particles but a distinctive hardness, indicating the difference in substrate conditions. The weight gain of all samples highly follows parabolic laws. The weight gain of the sample annealed at 400 °C has the fastest increase rate at the …
A Practical Anodic And Cathodic Curve Intersection Model To Understand Multiple Corrosion Potentials Of Fe-Based Glassy Alloys In Oh-Contained Solutions, Yingjie Li, Yonggang Wang, Bang An, Hui Xu, Yihua Liu, Laichang Zhang, Houyi Ma, Weimin Wang
A Practical Anodic And Cathodic Curve Intersection Model To Understand Multiple Corrosion Potentials Of Fe-Based Glassy Alloys In Oh-Contained Solutions, Yingjie Li, Yonggang Wang, Bang An, Hui Xu, Yihua Liu, Laichang Zhang, Houyi Ma, Weimin Wang
Research outputs 2014 to 2021
A practical anodic and cathodic curve intersection model, which consisted of an apparent anodic curve and an imaginary cathodic line, was proposed to explain multiple corrosion potentials occurred in potentiodynamic polarization curves of Fe-based glassy alloys in alkaline solution. The apparent anodic curve was selected from the measured anodic curves. The imaginary cathodic line was obtained by linearly fitting the differences of anodic curves and can be moved evenly or rotated to predict the number and value of corrosion potentials. © 2016 Li et al. This is an open access article distributed under the terms of the Creative Commons Attribution …
Distinction In Corrosion Resistance Of Selective Laser Melted Ti-6al-4v Alloy On Different Planes, Nianwei Dai, Laichang Zhang, Junxi Zhang, Xin Zhang, Qingzhao Ni, Yang Chen
Distinction In Corrosion Resistance Of Selective Laser Melted Ti-6al-4v Alloy On Different Planes, Nianwei Dai, Laichang Zhang, Junxi Zhang, Xin Zhang, Qingzhao Ni, Yang Chen
Research outputs 2014 to 2021
Electrochemical measurements and microstructural analysis were performed to study the corrosion resistance of different planes of Ti-6Al-4V alloy manufactured by selective laser melting (SLM). The electrochemical results suggest that its XY-plane possesses a better corrosion resistance compared to XZ-plane in 1 M HCl solution, in spite of slight difference in 3.5 wt.% NaCl solution, suggesting that the different planes exhibit more pronounced distinction in corrosion resistance in harsher solution system. The inferior corrosion resistance of XZ-plane is attributed to the presence of more α′ martensite and less β-Ti phase in microstructure for XZ-plane than for XY-plane of the SLM-produced Ti-6Al-4V …