Engineering Commons^™

Preparation, Ignition And Combustion Of Reactive Metal-Sulfur Nanocomposites, Ziyue Zhong

Theses

Mechanical milling is applied to synthesize reactive metal-sulfur nanocomposites. Specifically, magnesium-sulfur, aluminum-sulfur and zirconium-sulfur nanocomposite powders are prepared. Each powder particle contained homogeneously mixed sulfur and respective metal. These materials are expected to be stable in room air. They are also expected to release sulfur upon ignition; the released sulfur may serve as a biocidal agent. The ignition temperatures of the three prepared sulfur-bearing materials fall in a range of 750 - 1000 K. All prepared materials are successfully ignited in electrostatic discharge experiment as well as in a constant volume explosion experiment. The most sensitive material to spark ignition …

Dissolution Kinetics Of Model Api In Molten Polymer Excipients During Batch Processing, Shen Ji

Theses

In the pharmaceutical industrial application field, hot-melt extrusion (HME) has been recently introduced to develop new solid dosage forms and products. By dissolving the poorly–soluble active pharmaceutical ingredients (API) into water-soluble polymers, the bioavailability of the Class II (with low solubility and high permeability in water) API in Biopharmaceutical Classification System (BCS) could be significantly improved in the body. For readily water-soluble API, HME provides a new approach to produce a controlled release drug system. Hence, pharmaceutical HME is a promising processing method in the pharmaceutical industry.

However, HME has not been widely applied into the pharmaceutical industry. The thermal …

Development And Analysis Of Aluminum-Ptfe Reactive Composite Material, Siva Kumar Valluri

Theses

The shortcomings of micron sized aluminum due to the oxide barrier and two phase loses pose a hindrance for its efficient use as a fuel. In this study a fluoropolymer; Teflon’s inclusion in micron sized -325 mesh aluminum is suggested as a replacement to aluminum. Aluminum Teflon based energetic material see great potential for use in pyrotechnics, propellants and even explosives. A composite with composition Al-PTFE (90-10 wt. %) is prepared through Cryomilling and is shown to be a better method of preparation as compared to room temperature milling. The prepared materials are studied to identify best conditions. The analysis …

Carbon Dioxide Capture By Steel-Making Residues In A Fluidized Bed Reacto, Suhaib Mohammad Hameedi

Theses

Global warming is one of the most challenging problems facing societies these days, and it is known to be caused by the increasing emissions of Green House Gases (GHG's), mainly CO₂, from various human activities. To solve such a problem, or at least minimize its effects, several actions have been considered. One of these actions is carbon capture, which has many different options and techniques. This research focuses on the capture of CO₂ through reactions with steel-making residues, an alkaline solid by-product of the steel-making process. The aim is to sequester CO₂ and form carbonates, which …

Oil Recovery By Polymer Flooding; Sensitivity Analysis To Technical Parameters, Rana Osama Fahmi Saqer

Theses

Numerous enhanced oil recovery techniques including miscible gas injection, chemical, thermal and other methods are applied at the third phase of production after both primary and secondary recovery have been exhausted. Polymer flooding is one of the chemical methods that recover more oil by decreasing the mobility of the system; by increasing the viscosity of the injected water that results in an improvement in the volumetric sweep efficiency.

The objective of this work is to asses and select the development options using polymer process that maximize oil recovery for a synthetic reservoir model where technical parameters are optimized thoroughly.

Reservoir …

Oil Recovery By Flooding; Sensitivity Analysis To Technical Parameters, Rana Osama Fahmi Saqer

Theses

Numerous enhanced oil recovery techniques including miscible gas injection, chemical, thermal and other methods are applied at the third phase of production after both primary and secondary recovery have been exhausted. Polymer flooding is one of the chemical methods that recover more oil by decreasing the mobility of the system; by increasing the viscosity of the injected water that results in an improvement in the volumetric sweep efficiency.

The objective of this work is to asses and select the development options using polymer process that maximize oil recovery for a synthetic reservoir model where technical parameters are optimized thoroughly.

Reservoir …

Contact Angle And Ift Measurements Of Smart Water At Elevated Temperatures And Pressures For Evaluating Wettability In A Selected Carbonate Reservoir In The Uae, Jassim Abubacker Ponnambathayil

Theses

Water flooding has been regarded as a well-known secondary oil recovery method. In the recent years, extensive research on crude oil, brine, and rock systems has acknowledged that the composition of the injected water can change wetting properties of the reservoir during a water flood in a promising way to improve oil recovery. Hence, injection of “smart water” with correct salinity and composition is considered as a tertiary recovery method. The mechanism behind wettability alteration that is promoted by smart water injection has been a topic of discussion in carbonate and sandstone formations. In this work, some key properties of …

Synthesis Of A Renewable Sourced Thermotropic Polyester With 2,5-Furandicarboxylic Acid, Alicia Marie Marguerite Hurst

Theses

With the rapid depletion of non-renewable sourced materials, unpredictable fluctuations in the prices of fossil fuels, and increased environmental awareness the need to develop biobased materials grows ever more desperate. Furan derivatives sourced from hexoses provide a promising solution for replacing petrochemical based materials. One furan derivative in particular, 2,5-furandicarboxylic acid (FDCA), is especially promising due to its structural similarity to terephthalic acid and potential for use in the production of polyesters similar to PET, PPT, and PBT. This study investigated the synthesis, thermal and liquid crystalline properties of a totally renewable sourced thermotropic polyester based on FDCA. Fructose was …

Computational And Experimental Determination Of The Hydrodynamics In A Stirred Unbaffled Vessel Provided With Angle-Mounted Axial Impellers, Ji Ma

Theses

In most industrial applications, stirred tanks and reactors are typically provided with baffles to improve their mixing characteristics. However, in a number of pharmaceutical production facilities unbaffled vessels are commonly used. The absence of baffles is preferred in such cases because it reduces the potential for contamination and makes cleaning the vessel between batches easier. However, the lack of baffles also has a negative impact on the system’s hydrodynamics since it often results in poor mixing of the batch, especially if the impeller is centrally placed, since the liquid in such a system is subject to a strong tangential flow, …

A Preliminary Investigation Of The Sterile-Filterability Of Bcs Class Ii Drug Nanosuspensions Prepared Via Wet Stirred Media Milling, Parul Ohri

Theses

Drug nanoparticles can achieve targeting capabilities, enhanced dissolution rates and improved bioavailability when injected intravenously. Sterile filtration of drug nanoparticle suspensions (nanosuspensions) is critically needed for administration by intravenous delivery route. Avoiding gamma irradiation and high temperatures, sterile filtration could be an effective process to sterilize drug nanosuspensions. On the other hand, two major challenges must be tackled: drug particles must at least be smaller than the filter pore size and minimum amount of non-toxic stabilizers must be used to prevent side effects like pain on the injection site. The aim of this study is to prepare naproxen (NPX) nanosuspensions …