Open Access. Powered by Scholars. Published by Universities.®
- Keyword
-
- Construction engineering (2)
- AISC 360-16 (1)
- AISI S901-13 Rotational-Lateral Test Method (1)
- AISI S908 Base Test (1)
- Anchorage forces (1)
-
- Bi-linear behavior of panels and clips (1)
- Bracing (1)
- C-purlins (1)
- Diaphragm action (1)
- Diaphragm configuration (1)
- Diaphragm forces (1)
- Discrete torsional braces (1)
- Distance (1)
- Effective standoff (1)
- Energy efficiency (1)
- Finite element models (1)
- Flexibility (1)
- Flexural strength (1)
- Forces (1)
- Lateral bracing requirements (1)
- Lateral deformation (1)
- Lateral restraint (1)
- Lateral torsional buckling (1)
- Load carrying capacity (1)
- Load transfer (1)
- Metal buildings (1)
- Movement (1)
- Nonlinear (1)
- Panel (1)
- Panel-clip connections (1)
Articles 1 - 3 of 3
Full-Text Articles in Construction Engineering
Exploring The Effects Of Chip Flexibility On The Behavior Of Standing Seam Diaphragms To Brace Cold Formed Steel Purlins, Michael W. Seek
Exploring The Effects Of Chip Flexibility On The Behavior Of Standing Seam Diaphragms To Brace Cold Formed Steel Purlins, Michael W. Seek
Engineering Technology Faculty Publications
Cold-formed steel C- and Z-shaped purlins in standing seam roof systems rely on the diaphragm action provided by the panels to restrain lateral movements and thus increase the load carrying capacity the purlins. The clip connection between the purlin and the panel has inherent and sometimes intentional flexibility designed to accommodate thermal deformations. The lateral deformation behavior of standing seam systems supported by Zees is highly nonlinear and this behavior is not well understood. The flexibility has major implications on the transfer of diaphragm forces throughout these systems and simplified models often grossly overpredict the demands on the diaphragm and …
Lateral Bracing Of Beams Provided By Standing Seam Roof System: Concepts And Case Study, Gengrui Wei, Benjamin Schafer, Michael Seek, Matthew Eatherton
Lateral Bracing Of Beams Provided By Standing Seam Roof System: Concepts And Case Study, Gengrui Wei, Benjamin Schafer, Michael Seek, Matthew Eatherton
Engineering Technology Faculty Publications
The standing seam roof (SSR) system is the most commonly used roof system for metal buildings due to its superior durability, water tightness, and energy efficiency. In this type of system, SSR panels attach to Z-shaped or C-shaped purlins with clips, and the purlins are in turn connected to rafters (i.e. roof beams). For the design of metal building rafters against lateral torsional buckling, bottom flange braces provide torsional bracing to the rafter and the SSR system provides some lateral bracing. However, the degree to which the SSR system can restrain the rafter against lateral movement has not previously been …
Impact Of Clip Connection And Insulation Thickness On Bracing Of Purlins In Standing Seam Roof Systems, Michael W. Seek, Daniel Mclaughlin
Impact Of Clip Connection And Insulation Thickness On Bracing Of Purlins In Standing Seam Roof Systems, Michael W. Seek, Daniel Mclaughlin
Engineering Technology Faculty Publications
The flexural strength of purlins in standing seam roof systems is highly dependent upon the extent to which the sheathing provides lateral and torsional restraint. Typical models to predict the restraint provided by the sheathing assume that the plane of lateral resistance occurs at the top flange of the purlin. In reality, depending on the configuration of the clip and the amount of insulation located between the purlin and the clip, the plane of lateral resistance and corresponding center of rotation shifts above the top flange. This distance, referred to as the effective standoff, is important to evaluate the effectiveness …