Digital Commons Network^™

An Object-Oriented Discrete-Event Simulation System For Hierarchical Parallel Simulations, Kenneth W. Stauffer

Theses and Dissertations

The purpose of this research is to design and implement an object-oriented discrete-event simulation system which supports hierarchically constructed players in a parallel or distributed environment. This system design considers modularity and portability so additional modules may be implemented to experiment with new algorithms for both partitioning and synchronization. A simulation system which meets these requirements was partially implemented on an eight-node Intel Hypercube in C. A desired goal was to maintain the functionality of the existing BattleSim application. Test cases used measure the performance and correct operation of the new simulation architecture using a BattleSim subclass. Test results prove …

Modeling And Simulation Of Optical Characteristics Of Microelectromechanical Mirror Arrays, Peter C. Roberts

Theses and Dissertations

MEMS (Micro-Electro-Mechanical Systems) micromirror devices can be used to control the phase of a propagating light wavefront, and in particular to correct aberrations that may be present in the wavefront, due to either atmospheric turbulence or any other type of fixed or time and space varying aberrations. In order to shorten the design cycle of MEMS micromirror devices, computer software is developed to create, from MEMS micromirror device design data, a numerical model of the MEMS device. The model is then used to compute the far field diffraction pattern of a wavefront reflected from the device, and to predict the …

An Asic Power Analysis System For Digital Cmos Design, Du Van Nguyen

Dissertations and Theses

Consumers demand for products with ever-increasing functionality, performance, and longer battery life is making low power a critical factor in most system designs. Lower-power designs are less expensive to produce, more reliable, and cost less to operate - factors which create a real competitive advantage. As a result, ASIC designers are demanding better ways to analyze the power of their designs.

In this thesis, an ASIC Power Analysis System (APAS) is developed. APAS is an interactive simulation-based power analysis tool. Using a non-intrusive design technique, APAS can dynamically "snap on" to an existing simulation environment. APAS currently supports three ASIC …

Equalization Of A Non-Linear Phase Of A Low-Pass Filter, Rabih Khodor

Dissertations and Theses

In practice, an IIR filter can distort the information content of the signal because of its inherent non-linear phase characteristics introduced through the design of the filter. If the the receiver of the signal is the human ear, e.g., when a speech or music signal is to be processed, phase distortion is quite tolerable. But, in other applications it can be rejected as phase characteristics is required to be fairly linear. Applications of this type include data transmission, where the signal is to be interpreted by digital hardware, and image processing, where the signal is used to reconstruct an image …

The Multiple Pool Migrating Worker Paradigm : A Distributed System Framework And Model, Cynthia Ann Stanley

Dissertations and Theses

A network of workstations (NOW) can provide an inexpensive and effective distributed processing platform. The purpose of this thesis is two-fold, providing a methodology for distributed computing on a NOW first, and providing a model to predict and monitor performance second. The Multiple Pool-Migrating Worker (MPMW) paradigm uses multiple job pools to divide up tasks and migrating workers to balance the work load. The MPMW paradigm is a quick and efficient way of implementing problems using distributed processing without extensive knowledge of parallel programming. A model describing the MPMW paradigm is developed using queuing theory and Mean Value Analysis techniques. …

Improvements In A Hybrid Stochastic/Deterministic Method For Transient Three-Dimensional Neutron Transport, Charles L. Bentley

Doctoral Dissertations

This research develops an improved methodology (and corresponding code) for solving the time-dependent, three-dimensional Boltzmann Transport Equation with explicit representation of delayed neutrons. These improvements are incorporated in a modified version of the code TDKENO, entitled TDKENO-M. Specifically, these improvements are:

1. Incorporate the improved quasistatic methodology into an existing quasistatic framework. Specifically, include the flux shape derivative in the fixed source term instead of being neglected. Also, compute the point kinetics parameters deterministically by their inner product definitions.

2. Incorporate a hierarchy of three different integration time intervals for the numerical solution of the coupled set of ordinary differential …

Burst Pressure Prediction Of Filament Wound Composite Pressure Vessels Using Acoustic Emission, Marcus Elwood Fisher

Master's Theses - Daytona Beach

This research demonstrates how acoustic emission (AE) data from flaw growth activity can be used to predict burst pressures in filament wound composite pressure vessels. Acoustic emission data were taken during hydroproof testing for a set of eleven ASTM standard 5.75 inch diameter fiberglass/epoxy bottles. Amplitude distributions were created using only the AE data up to 25% of the expected burst pressure to simulate low level proof loadings (thereby avoiding damage to the bottles). The bottles were tested at three different temperatures -- 32°F, 70°F, and 110°F - and hydroproofed using two different pressurization schemes and two transducer configurations. Moreover, …

Elastic-Plastic Behavior And Limit Load Analysis Of Pipe Elbows Under In-Plane Bending And Internal Pressure, Mohab Ahmed Shalaby

Archived Theses and Dissertations

No abstract provided.

Digital Rosetta Stone: A Conceptual Model For Maintaining Long-Term Access To Digital Documents, Steven B. Robertson

Theses and Dissertations

Due to the rapid evolution of technology, future digital systems may not be able to read and/or interpret the digital recordings made by older systems, even if those recordings are still in good condition. This thesis addresses the problem of maintaining long-term access to digital documents and provides a methodology for overcoming access difficulties due to technological obsolescence. A review was conducted to determine the long-term access methods that have already been suggested by other researchers. These previously suggested methods are then combined with other ideas that were encountered and conceived while performing research for this project. The combination of …

Influence Of Tip Clearance On The Flowfield In A Compressor Cascade With A Moving Endwall, Richard J. Mcmullan

Theses and Dissertations

The effects of changing the blade tip clearances on the velocity and pressure flowfields within a compressor cascade were investigated in this experimental thesis. All moving endwall measurements were taken at a constant flow coefficient of 0.5 and tip clearances of 0.5, 1.0 and 2.0 percent chord. Hot-wire/film probes were used to determine the three-dimensional velocity vector components in various transverse planes - one upstream of the leading edges of the blades, three within the blade cascade and one downstream of the trailing edges of the blades. The transverse velocity vector plots showed a scraping of the tip leakage vortex …

Residual Strength And Fatigue Characterization Of Scs-6/Ti-6-4, Sang-Myung Lee

Theses and Dissertations

Metal matrix composite have potential in a variety of aerospace applications, but they should be better understood before they can be employed. Despite the many studies that have contributed to characterizing the fatigue response of titanium alloy MMCs, few have researched the residual strength. The purpose of this study was to investigate the residual strength and the frequency effects on the residual strength of an unidirectional laminate of SCS-6/Ti-6-4, a titanium alloy matrix based composite under tension-tension, load-controlled conditions at elevated temperatures and different frequencies. Specimens were fatigued at frequencies of 1 and 0.01Hz, and at maximum stress of 900MPa …

Development Of Synthetic Soils For Sorption Mass Transfer Model Validation, Thomas P. De Venoge

Theses and Dissertations

Existing sorption models often fail to describe grain scale sorption because of an inability to define the diffusion domain. A proposed improved model required testing to determine model validity. The testing method used a synthetic media of known geometry such that the distribution of sorption sites was known. Sorption rate data was obtained using batch experiments with the media. Data was used in comparison against model predicted rates. Fined sorption site distributions were compared to real distributions obtained by controlling sorbent geometries. Comparison determined model performance in fitting known distributions. The focus of this study was to (1) determine what …

Habitat Suitability Mapping Through Integration Of Multicriteria Evaluation Techniques With A Geographic Information System (Gis), Anthony A. Ference

Theses and Dissertations

The presence of an endangered species, the Pacific Pocket Mouse (PPM), in critical Marine Corps training areas aboard Camp Pendleton may adversely affect training activities that are crucial to meeting the Marine Corps' mission. Camp Pendleton must focus limited budgetary assets for live trapping surveys of the PPM in the areas of best habitat suitability and the purpose of this study was to develop a PPM habitat suitability map of Camp Pendleton. Suitability maps were developed by integrating expert opinion with the Camp Pendleton Geographic Information System (GIS) database.

A Comparative Analysis Of Two Alternatives To Chemical Aircraft Paint Stripping, George P. Joyce Ii

Theses and Dissertations

The Air Force must periodically strip and paint its aircraft to prevent the damaging effects of corrosion. The paint removal process typically involves the use of toxic chemicals such as methylene chloride which are soon to be banned as a result of impending environmental regulations and increased costs associated with handling and disposing of such material. The Air Force must choose an alternative to methylene chloride chemical stripping which complies with environmental regulations and reduces costs. This thesis compares the life cycle costs and environmental impacts of two alternatives to chemical aircraft stripping. Plastic Media Blasting (PMB) and Modified Medium …

Application Of A Finite-Volume Time-Domain Maxwell Equation Solver To Three-Dimensional Objects, Frederick G. Harmon

Theses and Dissertations

Concurrent engineering approaches for the disciplines of computational fluid dynamics (CFD) and electromagnetics (CEM) are necessary for designing future high-performance, low-observable aircraft. A characteristic-based finite-volume time-domain (FVTD) computational algorithm, developed for CFD and now applied to CEM, is implemented to analyze the radar cross section (RCS) of two three-dimensional objects, the ogive and cone-sphere. The FVTD formulation implements a Monotone Upstream-Centered Scheme for Conservation Laws (MUSCL) algorithm for the flux evaluation and a Runge-Kutta multi-stage scheme for the time integration. Developmental FVTD work for the thesis focused on algorithm development to analyze scattering and obtain RCS data for closed-surface perfect …

Adaptive Neural Network Controller For Atm Traffic, Jeffrey E. Larson

Theses and Dissertations

Broadband-Integrated Services Digital Networks (B-ISDN), along with Asynchronous Transfer Mode (ATM), were designed to meet the requirements of modern communication networks to handle multiple users and a wide variety of diverse traffic including voice, data and video. ATM responds to requests for admission to the network by analyzing whether or not the grade of service (GOS) requirement, specified in the admission request, can be guaranteed without violating the GOS guaranteed to traffic already accepted into the network. The GOS is typically a parameter such as cell loss rate (CLR), average delay, or some other measurement associated with network performance. In …

Optimization Of A Gps-Based Navigation Reference System, Jason B. Mckay

Theses and Dissertations

The development of increasingly accurate new aircraft navigation systems has caused the Air Force to develop a new Navigation Reference System to test them, called the Submeter Accuracy Reference System (SARS). The SARS is an inverted GPS system which consists of an array of GPS receivers on the ground and an airborne pseudolite mounted on the test aircraft. The SARS will provide a proof position estimate that is used to check the navigation system under test. Unfortunately, ground based inverted GPS systems tend to suffer from high geometric sensitivity to measurement errors. This research tackles the problem of optimizing the …

Interference Suppression For Spread Spectrum Signals Using Adaptive Beamforming And Adaptive Temporal Filter, Wonjin Park

Theses and Dissertations

Interference and jamming signals are a serious concern in an operational military communication environment. This thesis examines the utility and performance of combining adaptive temporal filtering with adaptive spatial filtering (i.e. adaptive beamforming) to improve the signal-to-jammer ratio (SJR) in the presence of narrowband and wideband interference. Adaptive temporal filters are used for narrowband interference suppression while adaptive beamforming is used to suppress wideband interference signals. A procedure is presented for the design and implementation of a linear constraints minimum variance generalized sidelobe canceler (LCMV-GSC) beamformer. The adaptive beamformer processes the desired signal with unity gain while simultaneously and adaptively …

Personnel Airdrop Risk Assessment Using Bootstrap Sampling, Wonsik Kim

Theses and Dissertations

Previous work on personnel airdrop problems involving jumpers has been (1) event-oriented entanglement rates, (2) number of canopy bumps, (3) landing injuries, and (4) deaths. The thesis expands this area of research by developing cumulative distribution functions of maximum possible chute entanglement risk for the C-17 using bootstrap techniques. By comparing the effects of various C-17 aircraft configurations on the entanglement CDF, this thesis shows that under certain configurations the risk of centerline entanglement for the C-17 is less than for the C-141.

Corrosion Inhibitor For Reinforcing Steel In Concrete, Hanan Abdel Aziz Elnouhy

Archived Theses and Dissertations

No abstract provided.

The Effect Of University Characteristics On The Bicycle Transportation Mode And Helmet Usage, Carlton C. Urban

Masters Theses

By performing a statistical analysis on data collected from the Internet, this study sought to determine if designated characteristics of a university actually affect the bicycle transportation mode and helmet usage on college campuses. The focus group for this research experience involved bicycle commuters affiliated with universities in the United States. Through the establishment of a World Wide Web home page and on-line survey, the author obtained data concerning estimated bicycle and helmet usage percentages, and campus characteristic data from bicyclist responses. The Internet was used as an innovative approach to collecting data. Essentially the participant would simply locate the …

Experimental Investigation Of Compressible Boundary Layers Under The Influence Of Pressure Gradients, Raymond C. Wier

Theses and Dissertations

This study examined the effect of mild pressure gradients on the mean and turbulent flow of high-speed boundary layers. Three Mach numbers (1.7, 3.0 and 5.0) were investigated. Three pressure gradients were examined; a zero pressure gradient (ZPG), a favorable pressure gradient (FPG), and a combined pressure gradient (CPG). The CPG consisted of an adverse pressure gradient followed by a favorable pressure gradient. Conventional pressure probes, hot-wire and particle image velocimetry (PIV) were used to examine the flow. Measurement included mean velocity, velocity turbulence intensity, mass flux turbulence intensity and energy spectra. Instantaneous (10 nsec) Mie scattering flow visualizations were …

Impacts Of Hypothetical NoX Sources On Ozone Formation In East Tennessee, Mamun Ahmed

Masters Theses

This thesis studied the effects of hypothetical NO_x sources located in East Tennessee on the tropospheric ozone concentrations impacting the Great Smoky Mountains National Park (GSMNP) using the Urban Airshed Model (UAM). The product of this study is a technique of assessing the potential impact of a new or modified large NO_x source on ozone concentrations within a Class I area, which includes and up-to-date detailed emissions inventory. The East Tennessee Modeling Domain (ETMD) consists of 94 counties in six different states with an area of 75,900 km²: Tennessee (40), North Carolina (22), South Carolina (8), …

Applying Probabilistic Risk Assessment And Decision Analysis Techniques To Avoid Excessive Remedial Investigation Costs, Alejandro Hinojos

Theses and Dissertations

The majority of remediation resources have been consumed by costly and lengthy remedial investigation studies to characterize the human health risk. Unable to deal directly with the uncertainty resulting from the convolution of the uncertainties in a multitude of variables, and heavily persuaded by the liabilities, decision makers and regulators have relied on conservative assumptions and more studies to take appropriate actions. The main objective of this research is to provide tools and techniques to aid risk analysts in determining whether it would be beneficial to gather additional information or whether the decision to take an appropriate action can be …

Evaluation Of Hazardous Material Life Cycle Cost Tools For Use In Air Force Hazardous Material Pharmacies, Rowene J. Resler

Theses and Dissertations

This research focuses on evaluation of various tools that assist in the selection of hazardous material substitutes. Substitute material consideration is a function of the Hazardous Material Pharmacy (HMP) when a hazardous material is requested for purchase and use in a current base operation. The substitute material decision is complex, involving identification of potential substitutes and then comparison of factors, such as cost, performance, and environmental effects, between the potential substitute and the material being requested. Various tools such as life cycle cost models, databases, and other information services can provide assistance to HMPs making substitution decisions.

Synergistic Decision-Making Systems: Using Models Of Decision-Making Behaviors And Resources To Design Better Decision-Making System, Ronald R. Carter

Masters Theses

Despite advances in decision-making systems, many practical issues remain unaddressed and much of the computer's potential for supporting decisions is unrealized. The existing systems are often limited to specific decision-making activities or domains, and they force the decision-maker to adopt a closed and inflexible way of doing things. What is needed is a new approach to building decision-making systems, one that is not focused on how decisions should be made, but on the behaviors and resources involved in decision-making and how they affect the results. This paper explores such an approach. It examines how models of decision-making behaviors and resources …

Modeling Plant Uptake Of Metal In Constructed Wetlands Supported By Experimentally Derived Uptake Rates, Michael B. Peake

Theses and Dissertations

Many communities and Air Force installations are using constructed wetlands to filter trace metals from their stormwater runoff. Constructed wetlands are attractive to industry for runoff mitigation because they are relatively cheap to build and operate and require little or no energy for operation. The purpose of this research project is to develop quantitative concepts for understanding the dynamics of metal uptake in constructed wetland plants by constructing a system dynamics model supported by experimental observation and offer environmental managers a tool to simulate, under a broad range of conditions, long term wetland exposure to stormwater runoff contaminated with trace …

Using Kriging To Interpolate Spatially Distributed Volumetric Medical Data, Stephen M. Matechik

Theses and Dissertations

Routine cases in diagnostic radiology require the interpolation of volumetric medical imaging data sets. Inaccurate renditions of interpolated volumes can lead to the misdiagnosis of a patient's condition. It is therefore essential that interpolated modality space estimates accurately portray patient space. Kriging is investigated in this research to interpolate medical imaging volumes. Kriging requires data to be spatially distributed. Therefore, magnetic resonance imaging (MRI) data is shown to exhibit spatially regionalized characteristics such that it can be modeled using regionalized variables and subsequently be interpolated using kriging. A comprehensive, automated, three-dimensional structural analysis of the MRI data is accomplished to …

Performance Analysis Of A Liquid Metal Heat Pipe Space Shuttle Experiment, Timothy J. Dickinson

Theses and Dissertations

Future spacecraft technologies require advanced high-temperature thermal control systems. Liquid metal heat pipes are considered ideally suited for such applications. However, their behavior during microgravity operation is not yet understood. This study investigated liquid metal heat pipe performance in such an environment. Three stainless steel/potassium heat pipes were flown on space shuttle mission STS-77 in May 1996. The objectives of the experiment were characterization of the frozen startup and restart transients, comparison of flight and ground test data to establish a performance baseline for analytical model validation, and assessment of three different heat pipe designs. Heat pipe performance was characterized …

Multidisciplinary And Multiobjective Optimization In Conceptual Design For Mixed-Stream Turbofan Engines, Luc J. J. P. Nadon

Theses and Dissertations

Despite major advances in design tools such as engine cycle analysis software and computer aided design, conceptual gas turbine engine design is essentially a trial-and-error process based on the experience of engineers. Modern optimization concepts, such as multidisciplinary optimization (MDO), and multiobjective optimization (MOO), linked with sequential quadratic programming (SQP) methods and genetic algorithms (GA), were applied to the conceptual engine design process to automate the conceptual design phase. Robust integrated computer codes were created to find the optimal values of eight engine parameters in order to minimize fuel usage, aircraft cost and engine annulus area over a given mission. …