Physics Commons^™

Development Of Dose Conversion Coefficients For Radionuclides Produced In Spallation Neutron Sources: Quarterly Progress Report 8/20/03 – 12/01/03, Phillip W. Patton, Mark Rudin

Transmutation Sciences Physics (TRP)

A research consortium comprised of representatives from several universities and national laboratories has been established as part of this project to generate internal and external dose conversion coefficients for radionuclides produced in spallation neutron sources. Information obtained from this multi-year study will be used to support the siting and licensing of future accelerator-driven nuclear initiatives within the U.S. Department of Energy complex, including the Spallation Neutron Source (SNS) and Accelerator Production of Tritium (APT) Projects. Determination of these coefficients will also fill data gaps for several hundred radionuclides that exist in Federal Guide Report No. 11 and in Publications 68 …

Afci Quarterly Input – Unlv October Through December, 2003, Harry Reid Center For Environmental Studies. Nuclear Science And Technology Division

Transmutation Research Program Reports (TRP)

Quarterly report highlighting research projects and objectives of the Transmutation Research Program at the Nuclear Science & Technology Division, Harry Reid Research Center.

The University of Nevada, Las Vegas supports the AFCI through research and development of technologies for economic and environmentally sound refinement of spent nuclear fuel. The UNLV program has four components: infrastructure, international collaboration, student-based research, and management and program support.

Identification Of Dynamic Properties Of Materials For The Nuclear Waste Package, Brendan O'Toole, Mohamed Trabia, Amy J. Smiecinski

Publications (YM)

Stainless steel 316L, titanium alloy grade 7, and alloy C22 are currently under consideration as candidate materials for use in various components associated with the spent nuclear fuel package, which must be designed to withstand structural deformation caused by static, thermal, and handling loads. In addition, it has to maintain its integrity in case of accidents, where it may be subjected to high loads over a very short period of time. Mechanical characteristics of these three materials under dynamic loading are not well documented. This paper describes the procedures and results obtained from experiments performed over a range of slow …

Task 32 Delayed Hydride Cracking Of Spent Fuel Cladding Under Repository Conditions, Ajit K. Roy, Anthony Hechanova, Amy J. Smiecinski

Publications (YM)

The objective of this quality-affecting task is to evaluate the susceptibility of spent nuclear fuel cladding materials (zirconium alloys) to stress corrosion cracking (SCC), delayed hydride cracking (DHC) and localized corrosion (pitting/crevice) in simulated repository environments. During the first year of this project, major efforts were focused on developing the infrastructure for performing the desired testing involving two highly corrosion-resistant alloys namely, zircaloy-2 (Zr-2) and zircaloy-4 (Zr-4) in simulated concentrated acidic water (SAW) and modified SAW (SAWM). Modification of the SAW chemistry was done by adding hydrochloric acid (HC1) to achieve lower pH. The construction of the "Materials Performance Laboratory …

The Logic Of Peace, Jonathan Schell

New England Journal of Public Policy

Jonathan Schell’s The Unconquerable World points the way out of the devastation of the twentieth century toward another, more peaceful path. And his investigations into the great nonviolent events of modern times — from Gandhi’s independence movement in India to the explosion of civic activity that brought about the surprising collapse of the Soviet Union — suggest foundations of an entirely new kind on which to construct an enduring peace. As Schell makes clear, all-out war, with its risk of human extinction, must cease to play the role of final arbiter. “The Logic of Peace,” printed here, is the final …

Afci Quarterly Input – Unlv July Through September, 2003, Harry Reid Center For Environmental Studies. Nuclear Science And Technology Division

Transmutation Research Program Reports (TRP)

Quarterly report highlighting research projects and objectives of the Transmutation Research Program at the Nuclear Science & Technology Division, Harry Reid Research Center.

The University of Nevada, Las Vegas supports the AFCI through research and development of technologies for economic and environmentally sound refinement of spent nuclear fuel. The UNLV program has four components: infrastructure, international collaboration, student-based research, and management and program support.

Design And Analysis For Melt Casting Metallic Fuel Pins Incorporating Volatile Actinides: Quarterly Progress Report 5/16/03- 8/15/03, Yitung Chen, Randy Clarksean, Darrell Pepper

Fuels Campaign (TRP)

The analysis of mold filling and solidification continues with progress being made for the consideration of these two features within one model. Analysis of the induction heating process of an Induction Skull Melter (ISM) is under study. Efforts are underway to validate the modeling procedure and specific comparisons are being made to previously published work. Few detailed modeling results have been reported by other researchers, making the validations an important part of the overall modeling process. Skin heating depths, power deposition rates, and other process parameters are being evaluated for use in upcoming furnace design simulations. Efforts are beginning on …

Dose Coefficients For Radionuclides Produced In A Spallation Neutron Source, John P. Shanahan

Transmutation Sciences Physics (TRP)

Internal and external dose coefficient values have been calculated for 14 anthropogenic radionuclides which are not currently presented in Federal Guidance Reports No. 11, 12, and 13 or Publications 68 and 72 of the International Commission on Radiological Protection. Internal dose coefficient values are reported for inhalation and ingestion of 1 μm and 5 μm particulates along with the f1 values and absorption types for the adult worker. Internal dose coefficient values are also reported for inhalation and ingestion of 1 μm particulates as well as the f1 values and absorption types for members of the public. Additionally, external dose …

Dramatic Nondipole Effects In Low-Energy Photoionization: Experimental And Theoretical Study Of Xe 5s, Oliver Hemmers, Renaud Guillemin, E. P. Kanter, B. Krassig, Dennis W. Lindle, S. H. Southworth, R. Wehlitz, J. Baker, A. C. Hudson, M. Lotrakul, D. Rolles, Wayne C. Stolte, I. Tran, A. Wolska, S. Yu, M. Ya Amusia, K. T. Cheng, L. V. Chernysheva, W. R. Johnson, S. T. Manson

Environmental Studies Faculty Publications

The Xe 5s nondipole photoelectron parameter γ is obtained experimentally and theoretically from threshold to ∼200  eV photon energy. Significant nondipole effects are seen even in the threshold region of this valence shell photoionization. In addition, contrary to previous understanding, clear evidence of interchannel coupling among quadrupole photoionization channels is found.

E1-E2 Interference In The Vuv Photoionization Of He, E. P. Kanter, B. Krassig, S. H. Southworth, Renaud Guillemin, Oliver Hemmers, Dennis W. Lindle, R. Wehlitz, M. Ya Amusia, L. V. Chernysheva, N. L. S. Martin

Environmental Studies Faculty Publications

We have measured the forward-backward asymmetry of photoelectron angular distributions produced in the vacuum ultraviolet photoionization of helium. This asymmetry, a consequence of the breakdown of the dipole approximation, measures the real part of the ratio of the quadrupole and dipole matrix elements. In the autoionization region, the strong energy dependence of the asymmetry permits an experimental separation of the ratio of those magnitudes from their phase difference. We experimentally determined the Fano parameters of the 2p²¹D₂ quadrupole resonance, and report improved values of the width Γ and line profile parameter q from those previously available …

Nucleon-Nucleon Spin Dependent Scattering Amplitudes To Describe Final State Interactions In Electromagnetic And Electroweak Nuclear Processes, William P. Ford

Physics Theses & Dissertations

There are currently no models readily available that provide nucleon-nucleon spin dependent scattering amplitudes at high energies ( s ≥ 6 GeV²⁾. This work aims to provide a model for calculating these high-energy scattering amplitudes. The foundation of the model is Regge theory since it allows for a relativistic description and full spin dependence. A parameterization of the amplitudes is presented. and comparisons of the solution to the assembled data set are shown. In addition, an application of the model to describe final state interactions in deuteron electrodisintegration is presented. Overall the model works as intended, and provides …

Phase Ii: Design And Analysis Of A Process For Melt Casting Metallic Fuel Pins Incorporating Volatile Actinides, Yitung Chen, Randy Clarksean, Darrell Pepper

Fuels Campaign (TRP)

This research report develops a model to analyze the transport of americium from the melt to the vapor phase above the crucible. The model considers mass transport in the melt, vaporization at the surface, and transport through the vapor phase. The greatest problem with the model is the uncertainty of the thermodynamic properties of the proposed ternary alloy. The details of the model and the specific quantities needed for the physical properties will be discussed.

Afci Quarterly Input – Unlv April Through June, 2003, Harry Reid Center For Environmental Studies. Nuclear Science And Technology Division

Transmutation Research Program Reports (TRP)

The University of Nevada, Las Vegas supports the AFCI through research and development of technologies for economic and environmentally sound refinement of spent nuclear fuel. The UNLV program has four components: infrastructure, international collaboration, student-based research, and management and program support.

Unlv Transmutation Research Program Proposal Year Iii: Design And Evaluation Of Processes For Fuel Fabrication, Georg F. Mauer

Fuels Campaign (TRP)

The objective of this project is the design and evaluation of manufacturing processes for transmuter fuel fabrication. The large-scale deployment of remote fabrication and refabrication processes will be required for all transmutation scenarios. Current program emphasis is on a five-year effort to determine the feasibility of transmutation as a technology to limit the need for repository storage of spent commercial fuel. The evaluation of the fabrication processes will create a decision support data base to document design, operations, and costs. Fabrication processes required for different fuel types differ in terms of equipment types, throughput, and cost. Differential cost Implications of …

Development Of Dose Coefficients For Radionuclides Produced In Spallation Neutron Sources, Phillip W. Patton

Transmutation Sciences Physics (TRP)

A research consortium comprised of representatives from several universities and national laboratories has been established as part of this on-going project to generate internal and external dose conversion coefficients for radionuclides produced in spallation neutron sources. Information obtained from this multi-year study will be used to support the siting and licensing of future accelerator-driven nuclear initiatives within the U.S. Department of Energy complex, including the Spallation Neutron Source (SNS) and the Advanced Fuel Cycle Initiative (AFCI) Projects. Determination of these coefficients will also fill data gaps for several hundred radionuclides that exist in Federal Guide Report No. 11 and in …

Design And Analysis For Melt Casting Metallic Fuel Pins Incorporating Volatile Actinides: Quarterly Progress Report 2/16/03- 5/15/03, Yitung Chen, Randy Clarksean, Darrell Pepper

Fuels Campaign (TRP)

Progress continues on the analysis of casting and solidification of the melt into molds. Modeling results for constant pressure casting, which is more realistic, have been obtained and produce physically realistic results for flow that starts, flows, and then eventually stops as it enters the mold. Potential mass transfer modeling features (Lammuir’s law for example) are being studied to enhance the capabilities of a mass transfer in a detailed system model. Different parameters are being varied as part of a parametric study to evaluate factors that impact the flow of the melt into the molds. The ability to include the …

Measurments Of Correlated Pair Momentum Distributions In 3he(E,E'Pp)N With Clas, Rustam Niyazov

Physics Theses & Dissertations

We have measured the ³He(e,e'pp)n reaction at 2.2 and 4.4 GeV over a wide kinematic range. The kinetic energy distribution for ’fast’ nucleons (p > 250 MeV/c) peaks where two nucleons each have 20% or less and the third or ‘leading’ nucleon carries most of the transferred energy. These fast nucleon pairs (both pp and pn) are back-to-back and carry very little momentum along q, indicating that they are spectators. Experimental and theoretical evidence indicates that we have measured N N correlations in ³He(e,e'pp)n by striking the third nucleon and detecting the spectator correlated pair.

Afci Quarterly Input – Unlv January Through March, 2003, Harry Reid Center For Environmental Studies. Nuclear Science And Technology Division

Transmutation Research Program Reports (TRP)

Quarterly report highlighting research projects and objectives of the Transmutation Research Program at the Nuclear Science & Technology Division, Harry Reid Research Center.

Design And Analysis Of A Process For Melt Casting Metallic Fuel Pins Incorporating Volatile Actinides, Yitung Chen, Darrell Pepper, Randy Clarksean

Fuels Campaign (TRP)

UNLV has developed and will continue to develop process models for the analysis of melt casting processes. This work will continue to be performed under the guidance of Argonne National Laboratory (ANL) engineers to insure that their knowledge and experience benefits the project. The research to be conducted during year three will center on performing detailed analyses on a conceptual design of an inductively heated skull-crucible casting furnace. Processing conditions will be analyzed, basic models utilized, and detailed heat and mass transfer models will be developed to analyze the most promising processes. The goal of this third year is to …

Experimental Investigation Of Steel Corrosion In Lead Bismuth Eutectic (Lbe): Characterization, Species Identification, And Chemical Reactions, John Farley, Dale L. Perry, Allen L. Johnson

Transmutation Sciences Materials (TRP)

The goal of the present research is to achieve a basic understanding of corrosion of steels by Lead Bismuth Eutectic (LBE). Liquid LBE is under consideration in the transmuter as both a spallation target and as a blanket coolant. There have been previous studies of LBE, especially by the Russians, who have over 80 reactor-years experience with LBE coolant in their Alpha-class submarine reactors. The Russians found that the presence of small amounts (ppm) of oxygen in the LBE significantly reduced corrosion. However, a fundamental understanding and verification of its role in the corrosion of steels is still very incomplete. …

University Of Nevada, Las Vegas Transmutation Research Program: Quarterly Report, Second Quarter Year 2 (June 2002 To August 2002), Anthony Hechanova

Transmutation Research Program Reports (TRP)

This Quarterly Report is a primary deliverable from the University of Nevada, Las Vegas (UNLV) Transmutation Research Program (TRP) Director to the U.S. Department of Energy (DOE) as described in the UNLV Advanced Accelerator Applications (AAA) proposal, and AAA FY02 Work Package. Note: during this quarter, the AAA national program changed names to the Advanced Fuel Cycle Initiative (AFCI) and the UNLV AAA University Participation Program changed its name to the Transmutation Research Program. The new names will be used in future references.

The TRP Director implements the program’s administration using staff from the Harry Reid Center for Environmental Studies …

Corrosion Of Steel By Lead Bismuth Eutectic: Quarterly Report November- December 2002 January 2003, John Farley

Transmutation Sciences Materials (TRP)

We continue to get valuable data from sputter depth profiling of steel samples. We meet weekly to discuss progress. We took depth-profiling data on D9 steel that had been exposed to LBE. This the first time we have examined this type of steel. This is important because it will enable us to separate out two effects and determine their effect on corrosion: composition of the steel vs surface preparation.

We started to plan a small experiments using a crucible of heated LBE, with the research program to be conducted at UNLV, on basic aspects of corrosion in this system. The …

An Analysis Of The Melt Casting Of Metallic Fuel Pins, Xiaolong Wu, Randy Clarksean, Yitung Chen Yitung.Chen@Unlv.Edu, Darrell Pepper, Mitchell K. Meyer

Fuels Campaign (TRP)

• Background

– Casting Volatile Actinides

– Need to Contain Americium

– Overview of Project

• Fuel Rod Model

– Physical System

– Governing Equations

• Preliminary Modeling Results

– Mold Materials

– Injection Casting Velocity

Nuclear Criticality, Shielding, And Thermal Analyses Of Separations Processes For The Transmutation Fuel Cycle, William Culbreth, Denis Beller

Separations Campaign (TRP)

The first step in any transmutation strategy is the separation of radionuclides in used nuclear fuel. The current separation strategy supporting the Advanced Fuel Cycle Initiative (AFCI) program is based on the use of a solvent extraction separation process to separate the actinides, fission products, and uranium from used commercial nuclear fuel, and on the use of pyrochemical separation technologies to process used transmuter fuels. To separate the fission products and transuranic elements from the uranium in used fuel, the national program is developing a new solvent extraction process, the Uranium Extraction Plus, or UREX+, process, based on the traditional …

Neutron Multiplicity Measurements Of Target/Blanket Materials, Carter D. Hull, Denis Beller

Transmutation Sciences Physics (TRP)

To optimize the performance of accelerator driven transmutation systems (ADS), engineers will need to design the system to operate with a neutron multiplication factor just below that of a critical, or self-sustaining, system. This design criteria requires particle transport codes that instill the highest level of confidence with minimal uncertainty, because the larger the uncertainties in the codes, the larger the safety margin required in the design and the lower the efficiency of the ADS transmuter. For current design efforts, the MCNPX code is used to determine neutron production and transport for spallation neutron systems.

While providing a very useful …

Development Of Dose Coefficients For Radionulides Produced In Spallation Neutron Sources: Annual Report, Phillip W. Patton, Mark Rudin

Transmutation Sciences Physics (TRP)

The University of Nevada, Las Vegas (UNLV) Transmutation Research Program has been tasked to support U.S. Department of Energy (DOE) efforts to assess the health risks associated with the operation of each of their accelerator-driven nuclear facilities for both NEPA and PSAR development. Quantifying the radiological risks to workers will have to be addressed during the design and siting of each of these facilities. U.S. Environmental Protection Agency (EPA) Federal Guidance Report No. 11 “Limiting Values of Intake and Air Concentration and Dose Conversion Factors for Inhalation, Submersion, and Ingestion”, developed two derived guides, Annual Limit on Intake (ALI) and …

Development Of Dose Coefficients For Radionuclides Produced In Spallation Targets, Phillip W. Patton, Mark Rudin

Transmutation Sciences Physics (TRP)

Dose coefficients permit simple determination of radiation dose associated with various exposure scenarios, and ultimately permit radiation safety personnel to assess the health risks to workers in a nuclear facility. Specifically, radiation safety personnel use dose coefficients to determine the radiation dose incurred to a tissue or organ system from a given exposure. These parameters are often expressed in terms of Annual Limits on Intake (ALIs) and Derived Air Concentrations (DACs).

Results from this study will be used to produce ALIs and DACs for these rare radionuclides created by spallation target systems that are not included in Federal Guidance Report …

Corrosion Of Steel By Lead Bismuth Eutectic, John Farley, Allen L. Johnson, Dale L. Perry

Transmutation Sciences Materials (TRP)

Materials for transmuter systems must be able to tolerate high neutron fluxes, great temperatures, and chemical corrosion. For lead bismuth eutectic (LBE) systems, there is an additional challenge in that the corrosive behaviors of materials in LBE are not well understood. Most of the available information on LBE systems has come from the Russians, who have over 80 reactor-years experience with LBE coolant in their Alpha-class submarine reactors. The Russians found that the presence of small amounts of oxygen (on the order of parts per million) in the LBE significantly reduced corrosion. However, a fundamental understanding and verification of its …

Surface Studies Of Corrosion Of Stainless Steel By Lead Bismuth Eutectic, Daniel Koury, Brian D. Hosterman, John Farley, Dale L. Perry, D. Parsons, J. Manzerova, Allen L. Johnson

Transmutation Sciences Materials (TRP)

Why is Lead Bismuth Eutectic Important?

• Changing national security stances have led to reexamination of nuclear waste reprocessing

• Dangerous actinides can be separated and

• Transmuted into safer products, creating a waste form dangerous for only hundreds of years, in addition to the production (up to 1/3 of the original fission energy) of useful energy

• Non-moderating coolants or spallation targets for production of fast neutrons is required for transmutation

• Russian experience with LBE coolants in their nuclear submarine fleet makes LBE an attractive possible transmutation coolant technology

• Corrosion of steel by LBE is an important …

Radiation Transport Modeling Using Parallel Computational Techniques, William Culbreth, Denis Beller

Reactor Campaign (TRP)

The second year of this project involved modeling several aspects of the LANCSE beam experiments:

• Modeling targets of varying diameter in air, in a vacuum, and in the presence of humid air;
• Modeling various proton beam profiles;
• Modeling the effects of off-axis proton beam impingement on the target;
• Modeling the asymmetry introduced by the steel table below the target;
• Modeling the effect of varying ratios of Pb to Bi and the effect of impurities; and
• Modeling the system, including other structures within the test room.

With the experience gained through modeling these systems, the UNLV researchers plan, with the assistance …