Physics Commons^™

Gate-Controlled Quantum Dots In Two-Dimensional Tungsten Diselenide And One-Dimensional Tellurium Nanowires, Shiva Davari Dolatabadi

Graduate Theses and Dissertations

This work focuses on the investigation of gate-defined quantum dots in two-dimensional transition metal dichalcogenide tungsten diselenide (WSe2) as a means to unravel mesoscopic physical phenomena such as valley-contrasting physics in WSe2 flakes and its potential application as qubit, as well as realizing gate-controlled quantum dots based on elementaltellurium nanostructures which may unlock the topological nature of the host material carriers such as Weyl states in tellurium nanowires.The fabrication and characterization of gate-defined hole quantum dots in monolayer and bilayer WSe2 are reported. The gate electrodes in the device design are located above and below the WSe2 nanoflakes to accumulate …

Materials Design For Energy Applications Using Ab- Initio Calculations, Hind Hemaidee Alqurashi

Graduate Theses and Dissertations

The structural, dynamical, electronic, and thermoelectric properties of rock-salt and wurtzite Cd1-xZnxO alloys, VTiRhZ (Al, Ga, In, Si, Ge, Sn) and ZrTiRhZ (Ge, Sn) quaternary Heusler alloys (QHAs) were investigated using density functional theory (DFT) and semi-classical Boltzmann transport theory. From these calculations, the alloys were identified as potential materials for future thermoelectric applications. Furthermore, the magnetic and spin-polarization properties of these QHAs were investigated. The total magnetic moments were found to be integer values for all QHAs. In addition, all studied QHAs except VTiRhAl possess a half-metallic behavior with a 100% spin-polarization. The half-metallic ferromagnetic behavior makes them promising …

Study Of Single-Photon Wave-Packets With Atomically Thin Nonlinear Mirrors, Christopher Klenke

Graduate Theses and Dissertations

A novel controlled phase gate for photonic quantum computing is proposed by exploiting the powerful nonlinear optical responses of atomically thin transition metal dichalcogenides (TMDs) and it is shown that such a gate could elicit a π-rad phase shift in the outgoing electric field only in the case of two incident photons and no other cases. Firstly, the motivation for such a gate is developed and then the implementation of monolayer TMDs is presented as a solution to previous realization challenges. The single-mode case of incident photons upon a TMD is derived and is then used to constrain the more …

Sigesn Light-Emitting Devices: From Optical To Electrical Injection, Yiyin Zhou

Graduate Theses and Dissertations

Si photonics is a fast-developing technology that impacts many applications such as data centers, 5G, Lidar, and biological/chemical sensing. One of the merits of Si photonics is to integrate electronic and photonic components on a single chip to form a complex functional system that features compact, low-cost, high-performance, and reliability. Among all building blocks, the monolithic integration of lasers on Si encountered substantial challenges. Si and Ge, conventional epitaxial material on Si, are incompetent for light emission due to the indirect bandgap. The current solution compromises the hybrid integration of III-V lasers, which requires growing on separate smaller size substrates …

Interplay Between The Lattice And Spin Degrees Of Freedom In Magnetoelectric And Magnetic Materials, Temuujin Bayaraa

Graduate Theses and Dissertations

This dissertation contains several investigations on the cross-coupling between structural and spin degrees of freedom in multiferroic and ferrimagnetic compounds by means of first-principles calculations and ab-initio-based Monte-Carlo simulations. We start with the reviews of magnetoelectricity, ferrimagnetism, strain engineering, followed by a brief introduction to first-principles computational methods, magnetic effective Hamiltonians, and other techniques that are utilized here. The results section of the dissertation can be divided into two parts. The first half focuses on magnetoelectric effects arising from different sources, while the second half is about the ferrimagnetic nature of materials. In the first part, we examine the epitaxial …

Investigation Of Optical And Structural Properties Of Gesn Heterostructures, Oluwatobi Gabriel Olorunsola

Graduate Theses and Dissertations

Silicon (Si)-based optoelectronics have gained traction due to its primed versatility at developing light-based technologies. Si, however, features indirect bandgap characteristics and suffers relegated optical properties compared to its III-V counterparts. III-Vs have also been hybridized to Si platforms but the resulting technologies are expensive and incompatible with standard complementary-metal-oxide-semiconductor processes. Germanium (Ge), on the other hand, have been engineered to behave like direct bandgap material through tensile strain interventions but are well short of attaining extensive wavelength coverage. To create a competitive material that evades these challenges, transitional amounts of Sn can be incorporated into Ge matrix to form …

Fabrication And Characterization Of Photodetector Devices Based On Nanostructured Materials: Graphene And Colloidal Nanocrystals, Wafaa Gebril

Graduate Theses and Dissertations

Photodetectors are devices that capture light signals and convert them into electrical signals. High performance photodetectors are in demand in a variety of applications, such as optical communication, security, and environmental monitoring. Among many appealing nanomaterials for novel photodetection devices, graphene and semiconductor colloidal nanocrystals are promising candidates because of their desirable and unique properties compared to conventional materials.

Photodetector devices based on different types of nanostructured materials including graphene and colloidal nanocrystals were investigated. First, graphene layers were mechanically exfoliated and characterized for device fabrication. Self-powered few layers graphene phototransistors were studied. At zero drain voltage bias and room …

Computational Modeling Of Black Phosphorus Terahertz Photoconductive Antennas Using Comsol Multiphysics With Experimental Comparison Against A Commercial Lt-Gaas Emitter, Jose Isaac Santos Batista

Graduate Theses and Dissertations

This thesis presents computational models of terahertz (THz) photoconductive antenna (PCA) emitter using COMSOL Multiphysics commercial package. A comparison of the computer simulated radiated THz signal against that of an experimentally measured signal of commercial reference LT-GaAs emitter is presented. The two-dimensional model (2D) aimed at calculating the photoconductivity of a black phosphorus (BP) PCA at two laser wavelengths of 780 nm and 1560 nm. The 2D model was applied to the BP PCA emitter and the LT-GaAs devices to compare their simulated performance in terms of the photocurrent and radiated THz signal pulse. The results showed better performance of …

Memory Module Design For High-Temperature Applications In Sic Cmos Technology, Affan Abbasi

Graduate Theses and Dissertations

The wide bandgap (WBG) characteristics of SiC play a significant and disruptive role in the power electronics industry. The same characteristics make this material a viable choice for high-temperature electronics systems. Leveraging the high-temperature capability of SiC is crucial to automotive, space exploration, aerospace, deep well drilling, and gas turbines. A significant issue with the high-temperature operation is the exponential increase in leakage current. The lower intrinsic carrier concentration of SiC (10-9 cm-3) compared to Si (1010 cm-3) leads to lower leakage over temperature. Several researchers have demonstrated analog and digital circuits designed in SiC. However, a memory module is …

Quantum Dynamical Phenomena In Non-Hermitian And Magnomechanical Systems, Saeid Vashahri Ghamsari

Graduate Theses and Dissertations

In this dissertation, we have investigated quantum dynamics via three case studies. First, we studied a system of two coupled waveguides respectively carrying optical damping and optical gain in addition to squeezing elements in one or both waveguides. Such a system is expected to generate highly entangled light fields in the two waveguides. We, however, show that the degree of the created entanglement is significantly affected by the quantum noises associated with the amplification and dissipation. Because of the noise effect, one can only have nonzero entanglement for a limited time interval. Second, we generalized the first project by considering …

Investigation Of The Structural, Electronic, And Thermoelectric Properties Of Mono- Chalcogenides, Aida Sheibani

Graduate Theses and Dissertations

The structural, electronic, and thermoelectric properties of GeTe are studied using density functional theory and Boltzmann transport equations. This material has a rhombohedral crystal structure in ambient temperature with a ferroelectric behavior due to lack of inversion symmetry. This study suggests that the presence of asymmetry in GeTe can lead to an improvement in the thermoelectric properties of this material. In addition, studies on introducing Group III, IV, and V dopants to GeSe show that while these impurities can improve the power factor and decrease the lattice thermal conductivity, they cannot enhance the figure of merit.

Design Of Submicron Structured Guided-Mode-Resonance Near-Infrared Polarizer, Marzia Zaman

Graduate Theses and Dissertations

The objective of this research is to design a larger submicron linear polarizer in the near-infrared wavelength range with a wide bandwidth which can be fabricated using the conventional thin-film microfabrication technology to reduce cost. For this purpose, a gold (Au) wire-grid transmission-type transverse-magnetic (TM) polarizer and a silicon (Si) wire-grid reflection-type TM polarizer, were designed using the guided-mode-resonance filter. The Au wire-grid TM polarizer of 700nm grating width and 1200nm grating period has 95% transmittance at 2400nm, more than 1000nm resonance peak bandwidth, and an extinction ratio (ER) of around 300 with a moderated level of sidebands. The 700nm …

Development Of A Comsol Microdialysis Model, Towards Creation Of Microdialysis On A Chip With Improved Geometries And Recovery, Patrick Pysz

Graduate Theses and Dissertations

Microdialysis (µD) sampling is a diffusion-limited sampling method that has been widely used in different biomedical fields for greater than 35 years. Device calibration for in vivo studies is difficult for current non-steady state analytes of interest correlated with both inflammatory response and microbial signaling molecules (QS); which exist in low ng/mL to pg/mL with molecular weights over a wide range of 170 Da to 70 kDa. The primary performance metric, relative recovery (RR), relating the collected sample to the extracellular space concentration varies from 10% to 60% per analyte even under controlled bench-top conditions. Innovations in microdialysis device design …

Interfacial Contact With Noble Metal - Noble Metal And Noble Metal - 2d Semiconductor Nanostructures Enhance Optical Activity, Ricardo Raphael Lopez Romo

Graduate Theses and Dissertations

Noble metal nanoparticles and two-dimensional (2D) transition metal dichalcogenide (TMD) crystals offer unique optical and electronic properties that include strong exciton binding, spin-orbital coupling, and localized surface plasmon resonance. Controlling these properties at high spatiotemporal resolution can support emerging optoelectronic coupling and enhanced optical features. Excitation dynamics of these optical properties on physicochemically bonded mono- and few-layer TMD crystals with metal nanocrystals and two overlapping spherical metal nanocrystals were examined by concurrently (i) DDA simulations and (ii) far-field optical transmission UV-vis spectroscopic measurements. Initially, a novel and scalable method to unsettle van der Waals bonds in bulk TMDs to prepare …

Growth Of Indium Nitride Quantum Dots By Molecular Beam Epitaxy, Steven P. Minor

Graduate Theses and Dissertations

Over the last decade, the evolution of the global consciousness in response to decreasing environmental conditions from global warming and pollution has led to an outcry for finding new alternative/clean methods for harvesting energy and determining ways to minimize energy consumption. III-nitride materials are of interest for optoelectronic and electronic device applications such as high efficiency solar cells, solid state lighting (LEDs), and blue laser (Blu-ray Technology) applications. The wide range of direct band gaps covered by its alloys (0.7eV-6.2eV) best illustrates the versatility of III-nitride materials. This wide range has enabled applications extending from the ultraviolet to the near …

Polarization Properties Of Airy And Ince-Gaussian Laser Beams, Sean Michael Nomoto

Graduate Theses and Dissertations

The description of polarization states of laser light as linear, circular polarization within the paraxial scalar wave approximation is adequate for most applications. However, this description falls short when considering laser light as an electromagnetic wave satisfying Maxwell's equations. An electric field with a constant unit vector for direction of the field and a space dependent complex scalar amplitude in the paraxial wave approximation does not satisfy Maxwell equations which, in general, requires all three Cartesian components of electric and magnetic fields associated for a nonzero laser beam to be nonzero.

Physical observation of passing a linearly polarized laser through …

Characterization Of Hydride Vapor Phase Epitaxy Grown Gan Substrates For Future Iii-Nitride Growth, Alaa Ahmad Kawagy

Graduate Theses and Dissertations

The aim of this research is to investigate and characterize the quality of commercially obtained gallium nitride (GaN) on sapphire substrates that have been grown using hydride vapor phase epitaxy (HVPE). GaN substrates are the best choice for optoelectronic applications because of their physical and electrical properties. Even though HVPE GaN substrates are available at low-cost and create the opportunities for growth and production, these substrates suffer from large macro-scale defects on the surface of the substrate.

In this research, four GaN on sapphire substrates were investigated in order to characterize the surface defects and, subsequently, understand their influence on …

Plasmonic Properties Of Nanoparticle And Two Dimensional Material Integrated Structure, Desalegn Tadesse Debu

Graduate Theses and Dissertations

Recently, various groups have demonstrated nano-scale engineering of nanostructures for optical to infrared wavelength plasmonic applications. Most fabrication technique processes, especially those using noble metals, requires an adhesion layer. Previously proposed theoretical work to support experimental measurement often neglect the effect of the adhesion layers. The first finding of this work focuses on the impact of the adhesion layer on nanoparticle plasmonic properties. Gold nanodisks with a titanium adhesion layer are investigated by calculating the scattering, absorption, and extinction cross-section with numerical simulations using a finite difference time domain (FDTD) method. I demonstrate that a gold nanodisk with an adhesive …

Optimizing The Plasmonic Enhancement Of Light In Metallic Nanogap Structures For Surface-Enhanced Raman Spectroscopy, Stephen Joseph Bauman

Graduate Theses and Dissertations

Technology based on the interaction between light and matter has entered something of a renaissance over the past few decades due to improved control over the creation of nanoscale patterns. Tunable nanofabrication has benefitted optical sensing, by which light is used to detect the presence or quantity of various substances. Through methods such as Raman spectroscopy, the optical spectra of solid, liquid, or gaseous samples act as fingerprints which help identify a single type of molecule amongst a background of potentially many other chemicals. This technique therefore offers great benefit to applications such as biomedical sensors, airport security, industrial waste …

Exfoliation, Synthesis, And Characterization Of Nanoscale Te, Takayuki Hironaka

Graduate Theses and Dissertations

Since the experimental discovery of graphene, two dimensional materials have enjoyed more attention and emphasis in academic research than nanowires, but the latter are an important area of study for creating 1D materials, or single atom chains, the next generation materials for advancing electronic devices. Atomically thin layers can be generated from 2D materials with weak bonds in one direction, and by applying this concept to one dimensional weakly bonded materials, we hypothesize that single atom chains with atomic-scale diameters may be produced. Tellurium (Te) and selenium (Se) have lattices consisting of spiral chains oriented along the c-axis, and each …

Fabrication And Characterization Of Electrochemical Glucose Sensors, Mohammed Marie

Graduate Theses and Dissertations

Electrochemical sensors based on the nanostructure of the semiconductor materials are of tremendous interest to be utilized for glucose monitoring. The sensors, based on the nanostructure of the semiconductor materials, are the third generations of the glucose sensors that are fast, sensitive, and cost-effect for glucose monitoring.

Glucose sensors based on pure zinc oxide nanorods (NRs) grown on different substrates, such ITO, FTO, and Si/SiO2/Au, were investigated in this research. Silicon nanowire (NW)- based glucose sensors were also studied. First, an enzyme-based glucose sensor was fabricated out of glass/ITO/ZnO NRs/BSA/GOx/nafion membrane. The sensor was tested amperometrically at different glucose concentrations. …

Free-Space Measurements Of Dielectrics And Three-Dimensional Periodic Metamaterials, Clifford E. Kintner

Graduate Theses and Dissertations

This thesis presents the free-space measurements of a periodic metamaterial structure. The metamaterial unit cell consists of two dielectric sheets intersecting at 90 degrees. The dielectric is a polyetherimide-based material 0.001” thick. Each sheet has a copper capacitively-loaded loop (CLL) structure on the front and a cut-wire structure on the back. Foam material is used to support the unit cells. The unit cell repeats 40 times in the x-direction, 58 times in the y-direction and 5 times in the z-direction. The sample measures 12” × 12” × 1” in total. We use a free-space broadband system comprised of a pair …

Characterization Of Coupled Gold Nanoparticles In A Sparsely Populated Square Lattice, Roy Truett French Iii

Graduate Theses and Dissertations

Metal nanoparticles deposited in regular arrays spaced at optical wavelengths support a resonance due to a coherent coupling between localized surface plasmon mode and lattice diffraction allowing for engineering of tunable devices for use in biological sensors, nanoantennae, and enhanced spectroscopy. Techniques such as electron beam lithography, focused ion beam lithography, nanosphere lithography, and nanoimprint lithography are used for fabrication but are limited by cost, device throughput, and small deposition. Polymer soft lithography and continuous dewetting of particles is a potentially viable alternative showing promise in all of those areas. This thesis developed the fabrication of a refined hydrophilic nanoimprinted …

Fabrication Of Infrared Photodetectors Utilizing Lead Selenide Nanocrystals, Justin Anthony Hill

Graduate Theses and Dissertations

Colloidal lead selenide and lead selenide / lead sulfide core/shell nanocrystals were grown using a wet chemical synthesis procedure. Absorbance and photoluminescence measurements were made to verify the quality of the produced nanocrystals. Absorbance spectra were measured at room temperature, while photoluminescence spectra were measured at 77 K. Organic ligands were exchanged for shorter ligands in order to increase the conductivity of the nanocrystals. Absorption and PL spectra for both core and core/shell nanocrystals were compared. Interdigital photodetector devices with varying channel widths were fabricated by depositing gold onto a glass substrate. Lead selenide nanocrystals were deposited onto these metallic …

Interactive Physics And Characteristics Of Photons And Photoelectrons In Hyperbranched Zinc Oxide Nanostructures, Garrett Edward Torix

Graduate Theses and Dissertations

As is commonly known, the world is full of technological wonders, where a multitude of electronic devices and instruments continuously help push the boundaries of scientific knowledge and discovery. These new devices and instruments of science must be utilized at peak efficiency in order to benefit humanity with the most advanced scientific knowledge. In order to attain this level of efficiency, the materials which make up these electronics, or possibly more important, the fundamental characteristics of these materials, must be fully understood. The following research attempted to uncover the properties and characteristics of a selected family of materials. Herein, zinc …

Experimental And Computational Studies Of Cortical Neural Network Properties Through Signal Processing, Wesley Patrick Clawson

Graduate Theses and Dissertations

Previous studies, both theoretical and experimental, of network level dynamics in the cerebral cortex show evidence for a statistical phenomenon called criticality; a phenomenon originally studied in the context of phase transitions in physical systems and that is associated with favorable information processing in the context of the brain. The focus of this thesis is to expand upon past results with new experimentation and modeling to show a relationship between criticality and the ability to detect and discriminate sensory input. A line of theoretical work predicts maximal sensory discrimination as a functional benefit of criticality, which can then be characterized …

The Effects Of Strain And Vacancies On The Electric And Vibrational Properties Of Ferroelectric Batio3 From First-Principles, Aldo Serge Michael Raeliarijaona

Graduate Theses and Dissertations

The studies of ferroelectricity (FE) are of technological significance because of the multitude of applicable properties that ferroelectric materials exhibit. The mastery, and control of these properties necessitate the knowledge of the fundamental physics governing these insulating materials.

In this dissertation I present the results of first-principles investigations of the behavior of the fundamental ferroelectric properties under strain, and in the presence of vacancies. In the first part I introduce the important FE properties, their common behavior, and their numerous valuable applications. Following this background on FEs, a review of theoretical methods is presented with topics such as: Density Functional …

Photoelectric Characterization Of Bacteriorhodopsin Reconstituted In Lipid Bilayer Membrane, Joel Kamwa

Graduate Theses and Dissertations

The objective of this work was to conduct basic research in biologically inspired energy conversion solutions. A photosynthetic protein (Bacteriorhodopsin) was reconstituted in a bi-layer membrane. Then, when a laser beam was shined on the membrane, the photon energy was used by the protein to pump protons across the membrane. The translocation of protons across the membrane was measured as photocurrent. For this purpose, a system was built to characterize the lipid bilayer membranes and to measure the photocurrent. The lipid bilayer membrane was characterized by its capacitance and resistance. A picoampere photocurrent was observed when Bacteriorhodopsin protein was present …

The Role Of Quantum Dot Size On The Performance Of Intermediate Band Solar Cells, Najla Alnami

Graduate Theses and Dissertations

The goal of this thesis is to understand possible mechanisms for the reported decrease of the open circuit voltage and solar cell efficiency in quantum dot (QD) intermediate band solar cells (IBSCs). More specifically, the effect of indium arsenide (InAs) QD height on the open circuit voltage and solar cell efficiency was studied in a systematic way. To explore this effect in QD solar cells, several solar cells (SCs) were grown with varying InAs QD heights. All experimental characteristics of the QD solar cells were compared to a reference structure without QDs. All samples were grown by Molecular Beam Epitaxy …

Optimization Of Plasmon Decay Through Scattering And Hot Electron Transfer, Drew Dejarnette

Graduate Theses and Dissertations

Light incident on metal nanoparticles induce localized surface oscillations of conductive electrons, called plasmons, which is a means to control and manipulate light. Excited plasmons decay as either thermal energy as absorbed phonons or electromagnetic energy as scattered photons. An additional decay pathway for plasmons can exist for gold nanoparticles situated on graphene. Excited plasmons can decay directly to the graphene as through hot electron transfer. This dissertation begins by computational analysis of plasmon resonance energy and bandwidth as a function of particle size, shape, and dielectric environment in addition to diffractive coupled in lattices creating a Fano resonance. With …