Oil, Gas, and Energy Commons^™

Knowledge-Based Information Resource Management System For Materials Of Sodium-Cooled Fast Reactor, Sean Hsieh

Reactor Campaign (TRP)

In the development of advanced fast reactors, materials and coolant/material interactions pose a critical barrier for higher temperature and longer core life designs. For advanced burner reactors (sodium cooled) such as EBR-II and FFTF, experience has shown that the qualified structural materials and fuel cladding severely limits the economic performance. In other liquid metal cooled reactor concepts, advanced materials and better understanding and control of coolant and materials interactions are necessary for realizing the potentials.

Liquid sodium has been selected as the primary coolant candidate for Gen. IV nuclear energy systems. Global Nuclear Partnership (GNEP) Advanced Burned Reactor (ABR) has …

Thermal Transient Flow Rate Sensor For High Temperature Liquid Metal Cooled Nuclear Reactor, Yingtao Jiang, Jian Ma

Reactor Campaign (TRP)

In nuclear power plants and accelerator driven systems (ADS) for nuclear waste treatment, it is important to monitor the coolant flow rate in the reactor core and pipe-line. In such a strong irradiation, high pressure, and temperature environment, the existing flow measurement techniques (such as Electromagnetic flow meters, Ultrasonic flow meters, Turbine flow meters, etc.) are not accurate and reliable.

The measurement of flow rates (mass flow rates or volume flow rate) plays a notable role in monitoring and controlling the experimental conditions. The bulk flow rates can be obtained through direct methods, which measure the amount of discharged fluids …

Modeling And Design Algorithms For Electromagnetic Pumps, Daniel P. Cook, Yitung Chen, Jian Ma

Reactor Campaign (TRP)

Electromagnetic (EM) induction pumps are used extensively in current and proposed nuclear power systems and industrial molten metal transfer operations. Although the Magnetohydrodynamic (MHD) theory that underlies the operation of these types of pumps has been studied extensively in the past few decades, the design of specific EM pumping systems for specific flow cases requires computational tools and expertise, which is lacking in the U.S. However, for the past two years, researchers at UNLV have been utilizing the TC-1 liquid metal loop system at UNLV and an Annular Linear Induction Pump (ALIP) to drive the liquid metal and to develop …

Knowledge-Based Information Resource Management System For Materials Of Sodium-Cooled Fast Reactor, Sean Hsieh

Reactor Campaign (TRP)

In the development of advanced fast reactors, materials and coolant/ material interactions pose a critical barrier for higher temperature and longer core life designs. For sodium-cooled fast reactors (SFRs) such as the Experimental Breeder Reactors in Idaho and the Fast Flux Test Facility in Hanford, experience has shown that qualified structural materials and fuel cladding severely limits their economic performance.

Liquid sodium has been selected as the primary coolant candidate for the Advanced Burner Reactor (ABR) of the Global Nuclear Partnership (GNEP). Materials improvement has been identified as a major thrust to improve fast reactor economics. Researchers from universities, national …

Implementation Of Uncertainty Propagation In Triton/Keno, Charlotta Sanders, Denis Beller

Reactor Campaign (TRP)

Monte Carlo methods are beginning to be used for three dimensional fuel depletion analyses to compute various quantities of interest, including isotopic compositions of used nuclear fuel. The TRITON control module, available in the SCALE 5.1 code system, can perform three-dimensional (3-D) depletion calculations using either the KENO V.a or KENO-VI Monte Carlo transport codes, as well as the two-dimensional (2-D) NEWT discrete ordinates code. To overcome problems such as spatially nonuniform neutron flux and non-uniform statistical uncertainties in computed reaction rates and to improve the fidelity of calculations using Monte Carlo methods, uncertainty propagation is needed for depletion calculations.

Decoupling And Disturbance Rejection Control For Target Circulation, Jian Ma, Joon S. Lee, Woosoon Yim

Reactor Campaign (TRP)

The Target Complex loop TC-1 was originally conceived as part of an accelerator-driven system (ADS) pilot plant that was designed and developed by the Institute of Physics and Power Engineering (IPPE) and Experimental and Development Organization (EDO) “Gidropress” in Obninsk, Russia, under the International Science and Technology Center Project #559 in 1998. It was to be used as the target in a 1 MWth ADS experiment run off of the LANSCE proton accelerator at Los Alamos National Laboratory (LANL). When the U.S. transmutation program changed priorities from accelerator-driven systems towards nuclear fission reactors, the TC-1 loop was brought to UNLV …

Monaco/Mavric Evaluation For Facility Shielding And Dose Rate Analysis, Charlotta Sanders, Denis Beller

Reactor Campaign (TRP)

The dimensions and the large amount of shielding required for Global Nuclear Energy Partnership (GNEP) facilities, advanced radiation shielding, and dose computation techniques are beyond today’s capabilities and will certainly be required. With the Generation IV Nuclear Energy System Initiative, it will become increasingly important to be able to accurately model advanced Boiling Water Reactor and Pressurized Water Reactor facilities, and to calculate dose rates at all locations within a containment (e.g., resulting from radiations from the reactor as well as the from the primary coolant loop) and adjoining structures (e.g., from the spent fuel pool).

The MAVRIC sequence is …

Implementation Of Uncertainty Propagation In Triton/Keno: To Support The Global Nuclear Energy Partnership, Charlotta Sanders, Denis Beller

Reactor Campaign (TRP)

Monte Carlo methods are beginning to be used for three-dimensional fuel depletion analyses to compute various quantities of interest, including isotopic compositions of used fuel.1 The TRITON control module, available in the SCALE 5.1 code system, can perform three dimensional (3-D) depletion calculations using either the KENO V.a or KENO-VI Monte Carlo transport codes, as well as the two-dimensional (2- D) NEWT discrete ordinates code. For typical reactor systems, the neutron flux is not spatially uniform. For Monte Carlo simulations, this results in non-uniform statistical uncertainties in the computed reaction rates. For spatial regions where the flux is low, e.g., …

Monaco/Mavric Evaluation For Facility Shielding And Dose Rate Analysis: To Support The Global Nuclear Energy Partnership, Charlotta Sanders, Denis Beller

Reactor Campaign (TRP)

Monte Carlo methods are used to compute fluxes or dose rates over large areas using mesh tallies. For problems that demand that the uncertainty in each mesh cell be less than some set maximum, computation time is controlled by the cell with the largest uncertainty. This issue becomes quite troublesome in deep-penetration problems, and advanced variance reduction techniques are required to obtain reasonable uncertainties over large areas.

In this project the MAVRIC sequence will be evaluated along with the Monte Carlo engine Monaco to investigate its effectiveness and usefulness in facility shielding and dose rate analyses. A previously MCNP-evaluated cask …

Modeling And Design Algorithms For Electromagnetic Pumps, Daniel P. Cook

Reactor Campaign (TRP)

Electromagnetic (EM) induction pumps are used in a number of nuclear energy related applications, such as circulation of molten lead-bismuth eutectic alloys in neutron targets, and circulation of liquid sodium metal in Gen IV Sodium-cooled Fast Reactors (SFR). Because EM pumps have no moving parts which can fail, they are considerably more reliable than conventional mechanical pumps for molten metal usage, and thus EM pumps are favored over mechanical pumps even though their pumping efficiency is lower and their initial cost is higher when compared to mechanical pumps of similar flow rates.

The research objectives of this task are:

• A …

Thermal Transient Flow Rate Sensor For High Temperature Liquid Metal Cooled Nuclear Reactor, Yingtao Jiang

Reactor Campaign (TRP)

In nuclear power plants and accelerator driven system (ADS) for nuclear waste treatment, it is important to monitor the coolant flow rate in the reactor core and pipe-line. In such a strong irradiation, high pressure and temperature environment, no accurate local flow measurement technique is readily available. Electromagnetic (EM) flow meter is popular in low temperature application as it is a non-intrusive technology. However, additional voltage will be produced due to temperature, flow, pressure, the chemical properties of the liquid metal and surface condition of the steel walls. In addition, the non-definite wetting behavior of liquid lead-bismuth to the electrically …

Decoupling And Disturbance Rejection Control For Target Circulation, Jian Ma, Joon S. Lee, Woosoon Yim

Reactor Campaign (TRP)

In 1998, the Institute of Physics and Power Engineering (IPPE) and Experimental and Development Organization “Gidropress” in Russia, began the design and construction of a prototype lead-bismuth eutectic (LBE) accelerator target, the Target Complex 1 (TC-1), under the International Science and Technology Center (ISTC) project #559 (“Pilot Flow Lead-Bismuth Target of 1 MW Power for Accelerator Driven Systems”) in support of the international efforts to develop accelerator-driven spallation systems for nuclear transmutation and other applications.

During the thermal and engineering test of the TC-1 in 2005 at UNLV, it was observed that the existing control algorithm led to a very …

Decoupling And Disturbance Rejection Control For Target Circulation Loop, Xiuju Tan

Reactor Campaign (TRP)

The primary objective is to modify the existing control algorithm of the pilot target circuit (TC-1) loop to achieve precise temperature control. Safety concerns, the alarm system, and a user-friendly design are the secondary objectives.

The decoupling and active disturbance rejection controls are the effective control scheme in this special multivariable control process to TC-1 loop.

The research objectives are:

• To identify the interacting terms between heater inputs and target temperature outputs in each zone experimentally,

• To design of decoupling and active disturbance rejection control (ADRC),

• To monitor system through internet based remote monitoring, automatic alarming and …

Magnetohydrodynamic Simulation Of Electromagnetic Pump In Tc-1, Lillian J. Ratliff

Reactor Campaign (TRP)

The pilot molten lead-bismuth target circuit (TC-1) in university of Nevada Las Vegas (UNLV) was designed for beam power of 1 MW accelerator driven system (ADS). The TC-1 is a liquid lead-bismuth eutectic (LBE) circulation loop. Circulation of the liquid alloy is driven by an annular linear induction pump (ALIP). Experimental measurements of system parameters have yielded a surprisingly low pump efficiency of less than 1%. A numerical study of the pump efficiency is being conducted to determine which operational parameters are responsible for this low efficiency and to give insight into future EM pump design. The numerical study will …

Radiation Transport Modeling Using Parallel Computational Techniques, William Culbreth, Denis Beller

Reactor Campaign (TRP)

One of the most significant tools available for the design and analysis of accelerator-driven systems, such as the systems proposed for transmutation, is the high-energy particle transport code MCNPX. The MCNPX code suite, developed by the national laboratories, allows researchers and engineers to model the complex interactions of high-energy particles with the target and related systems, including the spallation reaction and subsequent neutron multiplication expected in the accelerator targets.

The next stage in the development of the MCNPX code suite is to validate the code by comparing the theoretical predictions from the models with experimental observations. Additionally, the nuclear database, …

Radiation Transport Modeling Using Parallel Computational Techniques, William Culbreth, Denis Beller

Reactor Campaign (TRP)

The second year of this project involved modeling several aspects of the LANCSE beam experiments:

• Modeling targets of varying diameter in air, in a vacuum, and in the presence of humid air;
• Modeling various proton beam profiles;
• Modeling the effects of off-axis proton beam impingement on the target;
• Modeling the asymmetry introduced by the steel table below the target;
• Modeling the effect of varying ratios of Pb to Bi and the effect of impurities; and
• Modeling the system, including other structures within the test room.

With the experience gained through modeling these systems, the UNLV researchers plan, with the assistance …

Radiation Transport Modeling Using Parallel Computational Techniques, William Culbreth, Denis Beller

Reactor Campaign (TRP)

The second year of this project involved modeling several aspects of the LANCSE beam experiments:

• Modeling targets of varying diameter in air, in a vacuum, and in the presence of humid air;
• Modeling various proton beam profiles;
• Modeling the effects of off-axis proton beam impingement on the target;
• Modeling the asymmetry introduced by the steel table below the target;
• Modeling the effect of varying ratios of Pb to Bi and the effect of impurities; and
• Modeling the system, including other structures within the test room.

With the experience gained through modeling these systems, the UNLV researchers plan, with the assistance …

Radiation Transport Modeling Using Parallel Computational Techniques, William Culbreth

Reactor Campaign (TRP)

The Advanced Fuel Cycle Initiative (AFCI) program will rely on the use of accurate calculations and simulations of criticality and shielding for the separation process of the longlived isotopes that present a significant safety hazard in commercial spent fuel. To help design and verify the safety of the separation process, the neutronics code MCNPX will be used to model the distribution of neutron flux within the fuel blanket and to determine the neutron multiplication, k_eff. However, the cross section libraries and computational methods used by MCNPX at these neutron energies still have some uncertainty and will require validation. …

Monte Carlo Verification And Modeling Of Lead-Bismuth Spallation Targets, Daniel R. Lowe

Reactor Campaign (TRP)

No abstract provided.

Radiation Transport Modeling Of Beam-Target Experiments For The Aaa Project: Quaterly Report, June 01- August 31, 2002, William Culbreth

Reactor Campaign (TRP)

The national development of technology to transmute nuclear waste depends upon the generation of high-energy neutrons produced by proton spallation. Proton accelerators, such as LANSCE at the Los Alamos National Laboratory, are capable of producing 800 MeV protons. By bombarding a lead /bismuth target, each proton may generate up to 25 neutrons that can activate fission of transuranic isotopes. Students at UNLV have been involved in radiation transport calculations in collaboration with researchers at the Los Alamos National Laboratory and at the Argonne National Laboratory.

Radiation Transport Modeling Of Beam-Target Experiments For The Aaa Project: Quaterly Report, William Culbreth

Reactor Campaign (TRP)

The national development of technology to transmute nuclear waste depends upon the generation of high energy neutrons produced by proton spallation. Proton accelerators, such as LANSCE at the Los Alamos National Laboratory, are capable of producing 800 MeV protons. By bombarding a lead/bismuth target, each proton may generate 500 or more neutrons that can activate fission products or induce the fission of transuranic isotopes.

The Monte Carlo radiation transport code MCNPX developed at LANL is an important tool in the design of transmuter technology. It must be validated, however, for the neutron energy that will be employed. Experiments are being …

Radiation Transport Modeling Of Beam-Target Experiments, William Culbreth, Denis Beller

Reactor Campaign (TRP)

In the first year of the UNLV effort, researchers planned to develop the models of the experimental systems to predict the neutron flux and leakage from the experimental targets using the MCNPX code suite in order to help determine these missing parameters. To support these models, the researchers project, or estimate, values for the unknown parameters describing various events and phenomena occurring within the beam-target experiment. The results of these simulations will then be compared against the observed neutron leakage rates and energies. The estimates for the unknown parameters are then revised to correlate with the observed values (these parameters …

Project Continuation Proposal: Radiation Transport Modeling Of Beam-Target Experiments For The Aaa Project, William Culbreth

Reactor Campaign (TRP)

The AAA program will rely on the use of an accelerator-based transmuter1 to expose spent nuclear fuel to high-energy neutrons. The neutron flux will be sufficient to activate or fission the long-lived isotopes of Tc, I, Pu, Am, Cm, and Np that present a significant radiological hazard in commercial spent fuel. Transmuter fuel will be subcritical and a high-energy proton accelerator is needed to maintain the necessary neutron flux through the use of a neutron spallation target. The maximum neutron energy produced by spallation (~ 800 MeV) is significantly higher than that produced by a commercial light water reactor (~ …

Radiation Transport Modeling Of Beam-Target Experiments For The Aaa Project: Quaterly Report, William Culbreth

Reactor Campaign (TRP)

The national development of technology to transmute nuclear waste depends upon the generation of high energy neutrons produced by proton spallation. Proton accelerators, such as LANSCE at the Los Alamos National Laboratory, are capable of producing 800 MeV protons. By bombarding a lead/bismuth target, each proton may generate 500 or more neutrons that can activate fission products or induce the fission of transuranic isotopes.

The Monte Carlo radiation transport code MCNPX developed at LANL is an important tool in the design of transmuter technology. It must be validated, however, for the neutron energy that will be employed. Experiments are being …

Radiation Transport Modeling Of Beam-Target Experiments For The Aaa Project, William Culbreth

Reactor Campaign (TRP)

The AAA program will rely on the use of an accelerator-based transmuter to expose spent nuclear fuel to high-energy neutrons. The neutron flux will be sufficient to activate or fission the long-lived isotopes of Tc, I, Pu, Am, Cm, and Np that present a significant safety hazard in commercial spent fuel. Transmuter fuel will be subcritical and a high-energy proton accelerator is needed to maintain the necessary neutron flux through the use of a neutron spallation target. The maximum neutron energy produced by spallation (~ 600 MeV) is significantly higher than that produced by a commercial light water reactor (~ …