Industrial Technology Commons^™

Kwad - Ksu All Weather Autonomous Drone, Nick Farinacci, Sebastian Gomez, Stewart Baker, Ed Sheridan

Symposium of Student Scholars

"KWAD" or "KSU all-Weather Autonomous Drone" project was sponsored by Ultool, LLC to the KSU Research and Service Foundation to create a lightweight drone capable of capturing HD video during all-weather operations. The conditions of all-weather operation include rainfall of one inch per hour and wind speeds of up to twenty miles per hour. In addition, a global minimum structural safety factor of two is required to ensure the system's integrity in extreme weather conditions. Potential mission profiles include autonomous aerial delivery, topological mapping in high moisture areas, security surveillance, search and rescue operations, emergency transportation of medical supplies, and …

Wire Deflection Investigation During Wedm Of Aisi 304 Stainless Steel: An Experimental And Numerical Study, Sara A. El-Bahloul, Mohamed G. Elkhateeb

Mansoura Engineering Journal

Wire electrical discharge machining (WEDM) is a specific form of electrical discharge machining that employs a small diameter wire electrode to cut a narrow kerf in the workpiece. Since the wire deflection has a negative effect on the performed cutting, this research seeks to study the resultant wire deflection during WEDM of AISI 304 stainless steel. This study is performed with the help of three types of modeling; namely, mathematical modeling, experimental modeling, and thermo-mechanical finite element modeling. The mathematical modeling is performed to analyze the stresses and the wire lag, while the experimental modeling is achieved to observe the …

Fungi In Flux | Designing Regenerative Materials And Products With Mycelium, Arvind Bhallamudi

Masters Theses

As the world grapples with the escalating crisis of climate threats and environmental degradation, this research delves into the synergistic potential of design and biology, developing safe and sustainable materials for applications in prototyping, furniture and interior design. Harnessing the power of a unique organism - fungi, the study proposes an accessible, efficient, and resilient material resource system. It utilizes local waste streams and mycelium (the vegetative part of fungi) to grow functional structures. An experimental and small-scale protocol is modeled by testing bio-fabrication and bio-printing methods. The composites' performance qualities and characteristics are evaluated through mechanical testing and a …

A Qualitative Look Into Repair Practices, Jumana Labib

Undergraduate Student Research Internships Conference

This research poster is based on a working research paper which moves beyond the traditional scope of repair and examines the Right to Repair movement from a smaller, more personal lens by detailing the 6 categorical impediments as dubbed by Dr. Alissa Centivany (design, law, economic/business strategy, material asymmetry, informational asymmetry, and social impediments) have continuously inhibited repair and affected repair practices, which has consequently had larger implications (environmental, economic, social, etc.) on ourselves, our objects, and our world. The poster builds upon my research from last year (see "The Right to Repair: (Re)building a better future"), this time pulling …

Smart Manufacturing—Theories, Methods, And Applications, Zhuming Bi, Lida Xu, Puren Ouyang

Information Technology & Decision Sciences Faculty Publications

(First paragraph) Smart manufacturing (SM) distinguishes itself from other system paradigms by introducing ‘smartness’ as a measure to a manufacturing system; however, researchers in different domains have different expectations of system smartness from their own perspectives. In this Special Issue (SI), SM refers to a system paradigm where digital technologies are deployed to enhance system smartness by (1) empowering physical resources in production, (2) utilizing virtual and dynamic assets over the internet to expand system capabilities, (3) supporting data-driven decision making at all domains and levels of businesses, or (4) reconfiguring systems to adapt changes and uncertainties in dynamic environments. …

Chemical Clean Automated Loader, Jordyn Bryner

Williams Honors College, Honors Research Projects

TTM Technologies (TTM) is a global printed circuit board (PCB) manufacturer. The work described in this report was completed in the TTM North Jackson, Ohio location. This plant focuses primarily on the manufacturing of rigid and rigid-flex PCBs for the aerospace and defense industry. TTM North Jackson has an ongoing labor dependency issue due to the shortage of workers the nation is facing. To solve this problem, TTM has focused the efforts of their new engineers and interns on automating processes that are labor dependent. The goal is to provide design guidance to be used later by TTM to automate …

Integration Of Blockchain Technology Into Automobiles To Prevent And Study The Causes Of Accidents, John Kim

Electronic Theses, Projects, and Dissertations

Automobile collisions occur daily. We now live in an information-driven world, one where technology is quickly evolving. Blockchain technology can change the automotive industry, the safety of the motoring public and its surrounding environment by incorporating this vast array of information. It can place safety and efficiency at the forefront to pedestrians, public establishments, and provide public agencies with pertinent information securely and efficiently. Other industries where Blockchain technology has been effective in are as follows: supply chain management, logistics, and banking. This paper reviews some statistical information regarding automobile collisions, Blockchain technology, Smart Contracts, Smart Cities; assesses the feasibility …

An Improved Earned Value Management Method Integrating Quality And Safety, Brian Briggs

LSU Doctoral Dissertations

The construction industry invests significant time and money to improve quality and safety while reducing cost and schedule impacts. The industry has a sincere desire to improve construction project management methods to improve efficiency. Historically, quality and safety underperformances result from undermanaged quality control and safety activities. The cost and schedule impacts associated with poor quality work have always had an impact on construction operations. The unprecedented challenges and uncertainties of COVID-19 highlighted the need to improve the Earned Value Management (EVM) method within construction to reflect these quality and safety activities. The central goal of this dissertation is to …

Inventory Locating With Quuppa: The Design And Development Of A Real-Time Process Monitoring Web Application Solution, Dylan C. Moreland, Trevor J. Howell, John W. Takiff, Patrick S. Dillon, Theo E. Fritz, William K. Mcintyre

Industrial and Manufacturing Engineering

Viasat, Inc. requires precise inventory tracking at their production facility in San Diego, CA. Viasat has installed the Quuppa indoor real-time locating system (RTLS), which it uses to track the real-time position of high-value work-in-process items. In its current state, the system only displays in-the-moment location information, with no available functionality for storing historical data for review, analysis, or visualization. In addition, the data displayed is noisy and prone to significant random error. This paper provides an overview of RTLS methods and technologies, assesses alternative solutions to Viasat’s issue, demonstrates our RTLS integrated web app solution, analyzes its impact, and …

Development Of A Marine Biodegradable Target Balloon, Blake Samuel Robinson, Arash Sam Akhavi, David Leonardo Albarran-Martinez

Materials Engineering

The US Navy utilizes PVC target balloons, known as Killer Tomatoes, that are inflated onboard a naval vessel then deployed into the ocean to calibrate a variety of weaponry. The Navy has requested the investigation of biodegradable polymers to replace the PVC in attempts to reduce ocean waste that is generated from the leftover PVC material. After communicating with American Pacific Plastic Fabricators (APPF), the current manufacturer of the Killer Tomatoes, we gained an understanding of the manufacturing process and the material requirements that would allow a new material to be integrated into their current process. Two proprietary, trial polymers …

Generic Design Methodology For Smart Manufacturing Systems From A Practical Perspective, Part I—Digital Triad Concept And Its Application As A System Reference Model, Zhuming Bi, Wen-Jun Zhang, Chong Wu, Chaomin Luo, Lida Xu

Information Technology & Decision Sciences Faculty Publications

Rapidly developed information technologies (IT) have continuously empowered manufacturing systems and accelerated the evolution of manufacturing system paradigms, and smart manufacturing (SM) has become one of the most promising paradigms. The study of SM has attracted a great deal of attention for researchers in academia and practitioners in industry. However, an obvious fact is that people with different backgrounds have different expectations for SM, and this has led to high diversity, ambiguity, and inconsistency in terms of definitions, reference models, performance matrices, and system design methodologies. It has been found that the state of the art SM research is limited …

Generic Design Methodology For Smart Manufacturing Systems From A Practical Perspective. Part Ii—Systematic Designs Of Smart Manufacturing Systems, Zhuming Bi, Wen-Jun Zhang, Chong Wu, Chaomin Luo, Lida Xu

Information Technology & Decision Sciences Faculty Publications

In a traditional system paradigm, an enterprise reference model provides the guide for practitioners to select manufacturing elements, configure elements into a manufacturing system, and model system options for evaluation and comparison of system solutions against given performance metrics. However, a smart manufacturing system aims to reconfigure different systems in achieving high-level smartness in its system lifecycle; moreover, each smart system is customized in terms of the constraints of manufacturing resources and the prioritized performance metrics to achieve system smartness. Few works were found on the development of systematic methodologies for the design of smart manufacturing systems. The novel contributions …

Implementation Of An Autonomous Guided Vehicle (Agv), Allen St. Myers, Alan Miller

Williams Honors College, Honors Research Projects

This report thoroughly represents a proposal to AAM Metal Forming Minerva for the implementation of an AGV (Autonomous Guided Vehicle) Unit. Our recommendations are made with consideration to existing manufacturing processes and demonstrate how using an AGV would be a net positive investment for the company. By first examining the current operating costs, a three-tiered proposal is tailored based on increasing investment cost. Each tier increase encompasses the previous tiers’ proposed improvements while also growing in complexity and investment cost. The results of our research indicate that our Tier 2 proposal will provide the most benefit to our facility now …

Evaluation Of A Bulge Reduction Technology For Corrugated Fiberboard Containers Under Static Compression, Daan Peleman, Jay Singh, Koushik Saha, S. Roy

Journal of Applied Packaging Research

This research examines the effect of top-to-bottom static compression load on the bulge of RSC containers. The study compares a control regular slotted container (RSC) constructed with corrugated fiberboard to tape-reinforced designs. The bulge reduction, achieved using various tape placements and conditioning environments, were measured. Currently, no research on the effect of reinforcement tape towards reduction in the out-of-plane displacement (bulging) of the corrugated fiberboard panels has been undertaken. Samples related to four different container designs, varying by presence, quantity and the position of the reinforcement tape on the vertical panels, were tested and analyzed. The study involved the use …

Feasibility Of Electric Field Assisted Clogging Reduction In Cold Gas Spraying Nozzle, Hendric Tronsson

ENGS 88 Honors Thesis (AB Students)

The relatively novel cold spraying process expands its range of applications constantly. In order to continue this trend, this process still has various hurdles that need to be overcome such as clogging. Clogging within the cold gas spraying process causes porous coatings with less material properties and lower durability; a solution is needed in order to reduce the clogging and so expand the cold gas spraying applications. This study aimed to explore the feasibility of using an electric field to reduce clogging. To do so a simplified channel was used to simulate charged particle trajectory shifts under the influence of …

The Business Case For Industrial Safety: Revealing The Comprehensive Value Of Ergonomic Investments For Manufacturing Enterprises In Industry 4.0, Shane Stan

Honors Theses

How can today’s manufacturing enterprises construct, implement, and optimize modern safety initiatives in a manner that will present maximum return on investment and facilitate enterprise growth? Furthermore, how can these manufacturers assure individual ergonomic investments become part of a larger strategy to facilitate organizational change in safety? This work addresses these questions by placing industrial ergonomics in a business improvement context which comprehensively presents the financial returns and growth opportunities poised by modern safety initiatives. Additionally, to further strengthen the business case for industrial safety, an ergonomic action planning framework is established to guide the creation of holistic safety programs …

An Energy Profile Model For Fused Deposition Modeling 3d Printing Process, Calvin Hawkins

Research Opportunities for Engineering Undergraduates (ROEU) Program 2018-19

This project develops a strategy to monitor and estimate the energy consumption of fused deposition modeling (FDM) additive manufacturing, which will benefit manufacturers and designers seeking to design and manufacture products with minimal energy consumption.

Material Interactions And Self-Assembly In Inkjet Printing, Karam Nashwan Al-Milaji

Theses and Dissertations

Inkjet printing has attracted much attention in recent years as a versatile manufacturing tool, suitable for printing functional materials. This facile, low-cost printing technique with high throughput and accuracy is considered promising for a wide range of applications including but not limited to optical and electronic devices, sensors, solar cells, biochips, and displays. The performance of such functional devices is significantly influenced by the deposit morphology and printing resolution. Therefore, fabrication functional devices with precise footprints by inkjet printing requires deep understanding of ink properties, material interactions, and material self-assembly.

In conventional inkjet printing process, where sessile droplets are directly …

Remotely Controlled Industrial Robotic Arm And Simulation Of Automated Thermal Furnace, Prince Mehandi Ratta

Dissertations, Master's Theses and Master's Reports

The right execution of controllers ensures the correct analysis of information, generating efficient results and better optimizing the system. In this report, two controllers were designed. Firstly, a remotely controlled robotic arm, since there are no such type commercially available controllers. Moreover, robotic platforms are costly, so students and researchers are often unable to learn the concepts of programming industrial robots. This project makes a non-destructive, remotely-controlled robotic arm to better teach students and researchers about programming and control of robotic arms. Secondly, simulation of an automated thermal furnace for ArcelorMittal on SIMULINK, which is used for the annealing process …

Energy Efficiency Evaluation Of Blower Heater Non-Purge Compressed Air Dryers, Alexandra M. Botts

Graduate Theses, Dissertations, and Problem Reports

There are several compressed air dryers available for industrial use including, refrigerant, desiccant, and membrane. This research focuses on twin tower regenerative closed loop desiccant dryers, specifically: blower heater non-purge (BHNP) with and without cooling water pumps, Compressed-air Heater Purge (CHP), Blower Heater Purge (BHP), and Pressure Swing Heaterless (PSH). These styles of dryers are used mainly in industries that require extremely dry air such as, food manufacturing, medical air, or sensitive technology manufacturers. The research was conducted by collecting and analyzing real time current draw data on air compressors and associated dryers at eight different facilities (13 compressor systems) …

Advances In Composite Manufacturing Of Helicopter Parts, Tobias A. Weber, Hans-Joachim K. Ruff-Stahl

Hans-Joachim Ruff-Stahl

This study investigates and compares different methods for improving standard autoclave composite manufacturing in order to find suitable approaches to a more efficient composite production. The goal is not only a reduction in manufacturing times and costs but also quality enhancement. Improved part quality while decreasing costs enables a manufacturer of composite parts to expand its market share, especially in the helicopter market, which has been constantly shrinking over the last two years. Various approaches such as improved tooling technology, the use of automated systems for lamination as well as outsourcing are examined to provide an overview of possible advancements …

Manufacturing Process Simulation – On Its Way To Industrial Application, Dennis Otten, Tobias A. Weber, Jan-Christoph Arent

International Journal of Aviation, Aeronautics, and Aerospace

Manufacturing process simulation (MPS) has become more and more important for aviation and the automobile industry. A highly competitive market requires the use of high performance metals and composite materials in combination with reduced manufacturing cost and time as well as a minimization of the time to market for a new product. However, the use of such materials is expensive and requires sophisticated manufacturing processes. An experience based process and tooling design followed by a lengthy trial-and-error optimization is just not contemporary anymore. Instead, a tooling design process aided by simulation is used more often. This paper provides an overview …

Surface Topography Formation And Thermographic Analysis In Laser Polishing Of H13 Tool Steel, Joshua D. Miller

Electronic Thesis and Dissertation Repository

Laser polishing, in its simplest form, is the melting of a small layer of material via laser radiation. This creates a small molten pool which is re-distrusted across the surface, resulting in a much smoother finished surface. Although this process has been around for decades now, there has been a recent insurgence into industrial applications. Despite this, the phenomena that occur during the process are still not fully understood. Therefore, increasing the knowledge surrounding the process would be ideal.

To accomplish this, various input parameters of the process are altered to analyze the effect on the finished polished surface. Through …

Advances In Composite Manufacturing Of Helicopter Parts, Tobias A. Weber, Hans-Joachim K. Ruff-Stahl

International Journal of Aviation, Aeronautics, and Aerospace

This study investigates and compares different methods for improving standard autoclave composite manufacturing in order to find suitable approaches to a more efficient composite production. The goal is not only a reduction in manufacturing times and costs but also quality enhancement. Improved part quality while decreasing costs enables a manufacturer of composite parts to expand its market share, especially in the helicopter market, which has been constantly shrinking over the last two years. Various approaches such as improved tooling technology, the use of automated systems for lamination as well as outsourcing are examined to provide an overview of possible advancements …

Condition Assessment Of End-Of-Use Products For Remanufacturing, Jovan Morgan

Research Opportunities for Engineering Undergraduates (ROEU) Program 2016-17

The goal of the project is to use the automated 3-D laser scanner using a Capnut as a test object to detect surface defects, corrosion and calculation error through offline quality inspection. potentially reducing labor time and cost for both consumers and manufacturers.

Chocolate Bar Wrapping Machine, Austin M. Hoff, Daniel R. Trepke, Caleb B. Krichbuam

Williams Honors College, Honors Research Projects

Gilbert Chocolates has proposed to manufacture a machine to wrap chocolate bars. This machine is intended to replace two people wrapping the chocolate bars by hand, which is a time consuming method. This is especially apparent between October and January when the workers are working long hours in preparation for the Christmas rush of customers. Currently wrapping a bar takes about a minute and Gilbert Chocolates wants this time reduced down to 20-30 seconds. The budget for this project is set at $1000, and is being funded by the company. This machine needs to fit in a cubic foot of …

Fatigue Analysis Of The Welded Region In The Automotive Torsion Beam Rear Suspension System, Nan Zhan, Xiaochuan Zhang

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Solar Turbines Compressor Blade Installation Tools, Ryan Bruce, Carolyn Honeycutt, Stephen Oltrogge, Emmett Ross

Mechanical Engineering

The following report documents a California Polytechnic State University, Mechanical Engineering Senior Project sponsored by the gas turbine manufacturer, Solar Turbines. The senior project team consisted of four senior mechanical engineering students at Cal Poly, all with general concentrations; Ryan Bruce, Carolyn Honeycutt, Steve Oltrogge, and Emmett Ross. Kenneth Thomas sponsored the group and serves as the point of contact between the senior project team and Solar Turbines. He is a member of the Solar Turbines Mechanical Design Engineering Team and a Cal Poly graduate. Christoph Maurer served as the project team’s on-campus advisor.

A gas turbine uses internal combustion …

Computing Research In Academia: Classifications, Keywords, Perceptions, And Connections, Sung Han Kim

Theses and Dissertations

The Association for Computing Machinery (ACM) recognizes five computing disciplines: Computer Science (CS), Computer Engineering (CE), Information Technology (IT), Information Systems (IS), and Software Engineering (SE). Founded in 1947 the ACM is the world's largest society for computing educators, researchers, and professionals. While Computer Science has been a degree program since 1962, the other four are relatively new. This research focuses on understanding the graduate research in four of the five ACM disciplines (CS, CE, IT, and IS) using a large body of thesis and dissertation metadata. SE is not found in the metadata and graduate work in SE is …

Optimization Of Process Parameters In Micro Electrical Discharge Machining (Edm) Of Ti-6al-4v Alloy, Farshid Alavi

Masters Theses & Specialist Projects

Ti-6Al-4V has a wide range of applications such as in the automotive and aerospace industries. Nevertheless, titanium alloys are very difficult to machine by conventional methods. Micro-EDM is a non-conventional machining method that uses the thermal effect of precisely controlled sparks. Manufacturers are looking for the methods and optimal settings to increase the productivity of micro-EDM in terms of lessening machining time and tool wear. Moreover, surface integrity of the machined area is crucial for some products such as biomedical implants.

The objective of this study was to investigate the effects of the micro-EDM process parameters on response variables, in …