Open Access. Powered by Scholars. Published by Universities.®
Operations Research, Systems Engineering and Industrial Engineering Commons™
Open Access. Powered by Scholars. Published by Universities.®
Articles 1 - 6 of 6
Full-Text Articles in Operations Research, Systems Engineering and Industrial Engineering
Lead-Free Solder Joint Reliability – State Of The Art And Perspectives, Jianbiao Pan, Jyhwen Wang, David M. Shaddock
Lead-Free Solder Joint Reliability – State Of The Art And Perspectives, Jianbiao Pan, Jyhwen Wang, David M. Shaddock
Industrial and Manufacturing Engineering
There is an increasing demand in replacing tin-lead (Sn/Pb) solders with lead-free solders in the electronics industry due to health and environmental concern. The European Union recently passed a law to ban the use of lead in electronic products. The ban will go into effect in July of 2006. The Japanese electronics industry has worked to eliminate lead from consumer electronic products for several years. Although currently there are no specific regulations banning lead in electronics devices in the United States, many companies and consortiums are working on lead-free solder initiatives including Intel, Motorola, Agilent Technologies, General Electric, Boeing, NEMI …
Work Flow Policy And Within-Worker And Between-Workers Variability In Performance, Kenneth Howard Doerr, Tali Freed, Terence R. Mitchell, Chester A. Schriesheim, Xiaohua Zhou
Work Flow Policy And Within-Worker And Between-Workers Variability In Performance, Kenneth Howard Doerr, Tali Freed, Terence R. Mitchell, Chester A. Schriesheim, Xiaohua Zhou
Industrial and Manufacturing Engineering
Work flow policies are shown to induce a change in average between-workers variability (worker heterogeneity) and within-worker variability in performance times. In a laboratory experiment, the authors measured the levels of worker heterogeneity and within-worker variability under an individual performance condition, a work sharing condition, and a fixed assignment condition. The work sharing policy increased the levels of worker heterogeneity and worker variability, whereas the fixed assignment policy decreased them. These effects, along with work flow policy main effects on mean performance times and variability are examined. This article represents an initial step in understanding effects that may be important …
Wire Bonding Challenges In Optoelectronics Packaging, Jianbiao Pan, Patrice Fraud
Wire Bonding Challenges In Optoelectronics Packaging, Jianbiao Pan, Patrice Fraud
Industrial and Manufacturing Engineering
Wire bonding has been used in integrated circuit (IC) packaging for many years. However, there are many challenges in wire bonding for optoelectronics packaging. These challenges include bonding on sensitive devices, bonding over cavity, bonding over cantilevel leads and bonding temperature limitations. The optoelectronics package design brings another challenge, which requires wire bonding to have deep access capability. In this paper, the wire bonding technologies are reviewed and ball bonding and wedge bonding are compared. The variables that affect the wire bonding process are then discussed. Finally, the challenges of wire bonding in optoelectronics packaging are presented in detail.
Effect Of Chromium-Gold And Titanium-Titanium Nitride-Platinum-Gold Metallization On Wire/Ribbon Bondability, Jianbiao Pan, Robert M. Pafchek, Frank F. Judd, Jason Baxter
Effect Of Chromium-Gold And Titanium-Titanium Nitride-Platinum-Gold Metallization On Wire/Ribbon Bondability, Jianbiao Pan, Robert M. Pafchek, Frank F. Judd, Jason Baxter
Industrial and Manufacturing Engineering
Gold metallization on wafer substrates for wire/ribbon bond applications require good bond strength to the substrate without weakening the wire/ribbon. This paper compares the ribbon bondability of Cr/Au and Ti/TiN/Pt/Au metallization systems. Both chromium and titanium are used to promote adhesion between substrates and sputtered gold films. Both can diffuse the gold surface after annealing and degrade the wire/ribbon bondability. Restoring bondability by ceric ammonium nitrate (CAN) etch was investigated. Experiments were conducted to investigate the effect of Cr/Au and Ti/TiN/Pt/Au, annealing, and CAN etch processes on 25.4 times; 254 μm (1 × 10 mil) ribbon bonding. All bonds were …
Critical Variables Of Solder Paste Stencil Printing For Micro-Bga And Fine-Pitch Qfp, Jianbiao Pan, Gregory L. Tonkay, Robert H. Storer, Ronald M. Sallade, David J. Leandri
Critical Variables Of Solder Paste Stencil Printing For Micro-Bga And Fine-Pitch Qfp, Jianbiao Pan, Gregory L. Tonkay, Robert H. Storer, Ronald M. Sallade, David J. Leandri
Industrial and Manufacturing Engineering
Stencil printing continues to be the dominant method of solder deposition in high-volume surface-mount assembly. Control of the amount of solder paste deposited is critical in the case of fine-pitch and ultrafine-pitch surface-mount assembly. The process is still not well understood as indicated by the fact that industry reports 52-71% surface-mount technology (SMT) defects are related to the solder paste stencil printing process. The purpose of this paper is to identify the critical variables that influence the volume, area, and height of solder paste deposited. An experiment was conducted to investigate the effects of relevant process parameters on the amount …
A Supply Chain Management Tool For Linking Courses In Manufacturing Engineering , Daniel Waldorf, Sema E. Alptekin
A Supply Chain Management Tool For Linking Courses In Manufacturing Engineering , Daniel Waldorf, Sema E. Alptekin
Industrial and Manufacturing Engineering
A Recent Society of Manufacturing Engineers (SME) grant received by Manufacturing Engineering Program at Cal Poly has provided funds to strengthen its curricular focus on supply chain management, flexibility, business skills, quality, and process controls. New courses and laboratories are developed in electronics manufacturing, information technology, and supply chain management. A functioning supply chain environment has been developed to provide vertical integration among several courses. A software tool being developed in-house integrates the activities of the students who play the roles of customers and suppliers. Details of the various components of this comprehensive project are presented in this paper.