Nuclear Engineering Commons^™

Afci Quarterly Input – Unlv October 1 Through December 31, 2006, Harry Reid Center For Environmental Studies. Nuclear Science And Technology Division

Transmutation Research Program Reports (TRP)

Quarterly report highlighting research projects, activities and objectives of the Transmutation Research Program at the Nuclear Science & Technology Division, Harry Reid Research Center.

The University of Nevada, Las Vegas supports the AFCI through research and development of technologies for economic and environmentally sound refinement of spent nuclear fuel. The UNLV program has four components: infrastructure, international collaboration, student-based research, and management and program support.

High Temperature Heat Exchanger Project: Quarterly Progress Report July 1, 2006 Through September 30, 2006, Anthony Hechanova

Publications (NSTD)

Hydrodynamics and thermal numerical modeling coupled with sulfur trioxide decomposition for the one channel geometry with three different channel configurations were performed. The results obtained from the numerical modeling were compared with the baseline design under the same boundary and operation conditions. The case with diamond shaped channels has the highest percentage of sulfuric acid decomposition. The baseline channel geometry has the lowest pressure drop compared with other cases.

Afci Quarterly Input – Unlv July 1 Through September 30, 2006, Harry Reid Center For Environmental Studies. Nuclear Science And Technology Division

Transmutation Research Program Reports (TRP)

Quarterly report highlighting research projects, activities and objectives of the Transmutation Research Program at the Nuclear Science & Technology Division, Harry Reid Research Center.

The University of Nevada, Las Vegas supports the AFCI through research and development of technologies for economic and environmentally sound refinement of spent nuclear fuel. The UNLV program has four components: infrastructure, international collaboration, student-based research, and management and program support.

High Temperature Heat Exchanger Project: Quarterly Progress Report April 1, 2006 Through June 30, 2006, Anthony Hechanova

Publications (NSTD)

Numerical Analyses of the Ceramatec Sulfuric Acid Decomposer. Comparisons with experiments for the Ceramatec sulfuric acid decomposer coupon with eight straight channels for four different geometries and four different flow rates were performed. All of the operation and boundary conditions for the calculations were the same as in the Ceramatec experiments. Good agreement was found. The overall pressure drop difference between calculations and experiments for most of the cases is within 10%.

Dissolution, Reactor, And Environmental Behavior Of Zro 2 -Mgo Inert Fuel Matrix Neutronic Evaluation Of Mgo-Zro2 Inert Fuels, E. Fridman, A. Galperin, E. Shwageraus

Fuels Campaign (TRP)

In the second year of the “Dissolution, Reactor, and Environmental Behavior of ZrO₂-MgO Inert Fuel Matrix” project initiated and directed by UNLV, the Ben-Gurion University (BGU) group research was focused on the development of practical PWR core nuclear design fully loaded with Reactor Grade (RG) Pu fuel incorporated in fertile free matrix. The design strategy was based on the basic feasibility study results performed at BGU in the Year 1 of the project.

Afci Quarterly Input – Unlv April 1 Through June 30, 2006, Harry Reid Center For Environmental Studies. Nuclear Science And Technology Division

Transmutation Research Program Reports (TRP)

Quarterly report highlighting research projects, activities and objectives of the Transmutation Research Program at the Nuclear Science & Technology Division, Harry Reid Research Center.

The University of Nevada, Las Vegas supports the AFCI through research and development of technologies for economic and environmentally sound refinement of spent nuclear fuel. The UNLV program has four components: infrastructure, international collaboration, student-based research, and management and program support.

High Temperature Heat Exchanger Project: Quarterly Progress Report January 1, 2006 Through March 31, 2006, Anthony Hechanova

Publications (NSTD)

Quarterly Collaboration Meeting. The UNLVRF HTHX Project quarterly meeting was held in Albuquerque, NM, March 16 and 17, 2006. The purpose of the meeting was to promote collaboration and communication among the UNLV Research Foundation partners. A tour of Sandia National Laboratory was also provided that included a visit to their sulfuric acid decomposition test apparatus. There were 24 attendees from universities, national laboratories, and private industry. Collaborators discussed their research progress. The next meeting will be in July in Salt Lake City, UT.

Unlv Research Foundation High Temperature Heat Exchanger Development, Anthony Hechanova

Publications (NSTD)

Barriers addressed:

Nuclear Hydrogen Initiative R&D Plan – Material performance and component design and testing for: intermediate heat exchanger and high-temperature thermochemical water splitting (H2SO4 decomposition and HI decomposition). Improved materials for High Temperature Electrolysis.

Design Concepts And Process Analysis For Transmuter Fuel Manufacturing: Quarterly Progress Report #6, Kamalakar Alluri, Georg F. Mauer

Fuels Campaign (TRP)

Project Milestones

• Completed a systematic study seeking to arrive at an optimized plant configuration, using value engineering techniques in January 2006.

• Vision-based robot serving and automated plant safety monitoring is currently in progress.

Effect Of Silicon Content On The Corrosion Resistance And Radiation-Induced Embrittlement Of Materials For Advanced Heavy Liquid Metal Nuclear Systems: Quarterly Progress Report (November 2005 – January 2006), Ajit K. Roy

Transmutation Sciences Materials (TRP)

This task is intended to study the effect of Si content not only on the corrosion resistance but also on the radiation-induced embrittlement of martensitic stainless steels. The susceptibility of these alloys with different Si content to stress corrosion cracking, general corrosion and localized corrosion will be evaluated in the molten LBE and aqueous environments of different pH values using state-of-the-art testing techniques. Testing in the aqueous media is intended to develop baseline data for comparison purpose. Radiation-induced embrittlement of these alloys will initially be studied by irradiating the test specimens with bremmstrahlung gamma radiation from 20-40 MeV electron beams …

Development Of Integrated Process Simulation System Model For Spent Fuel Treatment Facility (Sftf) Design: Quarterly Progress Report January 1-March 31, 2006, Yitung Chen, Sean Hsieh

Separations Campaign (TRP)

The UNLV developed TRPSEMPro software package can access engineering modeling software, ASPEN Plus through its own interface. The new interface eliminates the user interaction with the complex ASPEN Plus package and also provides input and output results for analysis purpose. The current interface will keep improving on collecting multiple scenario runs and database population.

Two separation processes, acid and plutonium separations, are near completion. The unit operations were finished while some sensitive chemical data for certain species are unknown. Graduate student, Matthew Hodges, continues on finishing those processes using dummy values for those restricted variables. Once the processes complete, researchers …

Theoretical Modeling Of Protective Oxide Layer Growth In Non-Isothermal Lead-Alloys Coolant Systems: Quarterly Progress Report (01/01/06- 03/31/06), Yitung Chen

Transmutation Sciences Materials (TRP)

Research highlights:

• A cellular automaton model using method of global restructuring on the growth and corrosion during the formation of the passive layer has been developed.

• A stochastic model, which combines the surface growth and internal oxidation, has been developed to explain the oxidation mechanism of steels in liquid lead alloys.

• Two conference papers have been accepted and will be presented in 2006 International Congress on the Advances in Nuclear Power Plants (ICAPP '06).

Afci Quarterly Input – Unlv January 1 Through March 31, 2006, Harry Reid Center For Environmental Studies. Nuclear Science And Technology Division

Transmutation Research Program Reports (TRP)

Quarterly report highlighting research projects, activities and objectives of the Transmutation Research Program at the Nuclear Science & Technology Division, Harry Reid Research Center.

The University of Nevada, Las Vegas supports the AFCI through research and development of technologies for economic and environmentally sound refinement of spent nuclear fuel. The UNLV program has four components: infrastructure, international collaboration, student-based research, and management and program support.

Neutron Multiplicity Measurements For The Afci Program Final Quarterly Progress Report January-March 2006, Denis Beller

Transmutation Sciences Physics (TRP)

This project was developed to test a Russian-built Neutron Multiplicity Detector System (NMDS) for measuring neutrons generated in a central target by a variety of accelerators. To assist in experiment design and evaluation, we use the most advanced high-energy radiation transport code, MCNPX, to model experiments. Experimental results are compared to computational predictions and discrepancies are investigated. Initial plans were to conduct experiments using a 70-MeV proton cyclotron at the Crocker Nuclear Laboratory at the University of California at Davis and/or a 20 to 40 MeV electron linac (linear accelerator) at the Idaho Accelerator Center (IAC) at Idaho State University …

Reactor Physics Studies For The Afci Race Project: Reactor-Accelerator Coupling Experiments Project: Quarterly Progress Report January-March 2006, Denis Beller

Transmutation Sciences Physics (TRP)

In the RACE Project of the U.S. Advanced Fuel Cycle Initiative (AFCI), a series of accelerator driven subcritical systems (ADSS) experiments is being conducted at the Idaho State University’s Idaho Accelerator Center (ISU-IAC) and at the University of Texas (UT) at Austin, and will be conducted at the Texas A&M University. In these experiments electron accelerators are used to induce bremsstrahlung photon-neutron reactions in heavy-metal targets; this source of 10¹⁰ to 10¹³ n/s initiates fission reactions in the subcritical systems. These systems include a compact, transportable assembly at ISU and TRIGA reactors at UT-Austin and Texas A&M. These …

Dissolution, Reactor, And Environmental Behavior Of Zro2-Mgo Inert Fuel Matrix: Quarterly Report, January 2006 To March 2006, Kiel Steven Holliday, Thomas Hartmann, Kenneth Czerwinski

Fuels Campaign (TRP)

This project will examine inert matrix fuels containing ZrO₂ and MgO as the inert matrix, with the relative amount of MgO varied from 30% to 70% in ZrO₂. Reactor physics calculations will be used to examine suitable quantities of burnable poisons from the candidate elements Gd, Er, or Hf with reactor grade Pu providing the fissile component, with up to 10% of ²³⁹Pu. Ceramics will be synthesized and characterized based on the reactor physics results. The solubility of the fuel ceramics, in reactor conditions, reprocessing conditions, and repository conditions, will be investigated in a manner to …

Crystal Structure And Nano Structure Of Oxide-And Nitride Transmutation Fuel – Refinement Of Transmutation Fuel Processing For Surrogate And Radioactive Fuel Systems: Quarterly Report, January 2006 To March 2006, Chinthaka Silva

Fuels Campaign (TRP)

Transmutation-related research work at the National Laboratories, e.g. Los Alamos National Laboratory, is focused on mono-nitride ceramic fuel forms, and consists of closely coordinated “hot” actinide and “cold” inert and surrogate fuels work. Matrix and surrogate materials work involves three major components: (1) fuel matrix synthesis and fabrication, (2) fuel performance, and (3) fuel materials modeling. The synthesis and fabrication component supports basic material studies, as well as actinide fuel fabrication work through fuel fabrication process development.

This project, task 28, supports the TRP program by delivering structural data on surrogate and radioactive fuels. Crystal structure and nanostructures of the …

Nanometal Containing Nanocomposites And Photolithographic Polyaniline Nanofibers, Frank D. Blum, Sunil K. Pillalamarri, Lalani K. Werake, J. Greg Story, Massimo F. Bertino, Akira Tokuhiro

Chemistry Faculty Research & Creative Works

A report on recent progress from our laboratories on the nanostructures produced from novel synthesis techniques will be discussed. Using high-energy radiation (γ-rays) we have been able to produce conducting polymer nanofibers and nanorods of polyaniline and polypyrrole without the use of a separate template or capping agent. This technique has been extended, with the addition of metal ions, to a "one pot" synthesis, producing conducting nanocomposites. These nanocomposites contain metal nanoparticles which decorate the conducting nanofibers. We have also recently shown that these systems can be photopatterned to produce novel structures. We believe that these systems will be useful …

Synthesis And Properties Of Metallic Technetium And Technetium - Zirconium Alloys As A Radioactive Storage Waste Form To Stabilize The Technetium Waste Stream Of The Urex+1 Process, Frederic Poineau, Thomas Hartmann, Kenneth Czerwinski

Waste Forms Campaign (TRP)

In the AFCI program the UREX+1 process is proposed as one of the most promising technique to separate TRU (transuranic elements) form LWR spent nuclear fuel in the years to come. The application of UREX+1 results in good separation of the 5f-transuranics from the 4f-lanthanides, reduced waste volumes by eliminating the uranium content, and reduced waste package costs. Technetium-99 will be separated together with uranium and iodine within the first process steps. After the separation of uranium, technetium and iodine must be immobilized by their incorporation in a suitable waste storage form. Based on recent activities within the AFCI community, …

High Temperature Heat Exchanger Project: Quarterly Progress Report October 1, 2005 Through December 31, 2005, Anthony Hechanova

Publications (NSTD)

• Liquid Salt Technical Working Group Meeting. The first meeting of the Liquid Salt Technical Working Group was held on October 28, 2005 at the Pratt Whitney Rocketdyne facility in Canoga Park, CA. 20 experts from academia, industry, and national laboratories participated to discuss current state of knowledge and research needs for high temperature liquid salt applications.
• Nuclear Hydrogen Initiative Semi-annual Review. Several participants from the UNLVRF University Consortium gave technical presentations at the NHI Semi-annual Review meeting in Rockville, MD, November 9-10, 2005.
• Quarterly Collaboration Meeting. The University of Nevada, Las Vegas hosted a UNLVRF HTHX Project quarterly meeting December …

Hybrid Solar Cells From Water-Soluble Polymers, James T. Mcleskey Jr., Qiquan Qiao

Mechanical and Nuclear Engineering Publications

We report on the use of a water-soluble, light-absorbing polythiophene polymer to fabricate novel photovoltaic devices. The polymer is a water-soluble thiophene known as sodium poly[2-(3-thienyl)-ethoxy-4-butylsulfonate] or PTEBS. The intention is to take advantage of the properties of conjugated polymers (flexible, tunable, and easy to process) and incorporate the additional benefits of water solubility (easily controlled evaporation rates and environmentally friendly). The PTEBS polythiophene has shown significant photovoltaic response and has been found to be effective for making solar cells. To date, solar cells in three different configurations have been produced: titanium dioxide (TiO2) bilayer cells, TiO2 bulk heterojunction solar …

Development Of Integrated Process Simulation System Model For Spent Fuel Treatment Facility (Sftf) Design, Yitung Chen, Sean Hsieh

Separations Campaign (TRP)

The overall goal of this project is the creation of a framework that combines all the strengths of AMUSE’s complicated calculations, well-established commercial system process packages, and TRPSEMPro’s flexible parameter optimization modules. Development of the process simulation code can be done using the solvent extraction process at Argonne National Laboratory in collaboration with the UNLV Nevada Center for Advanced Computational Methods.

The major objectives are the following:

• Develop a framework for simulating the Spent Fuel Treatment Facility (SFTF) process using AMUSE code, commercial process package, such as ASPEN-PLUS, and system engineering model.
• Develop a middleware package that can communicate between …

Neutron Multiplicity Measurements Of Target/Blanket Materials, Denis Beller

Transmutation Sciences Physics (TRP)

The U.S. Advanced Fuel Cycle Initiative (AFCI) is a program to develop economic and environmental methods to reduce the impact of waste from commercial nuclear fuel cycles. One concept for near-complete destruction of waste isotopes from used nuclear fuel is accelerator-driven transmutation. High-power accelerators would be used to produce high-energy charged particles, which then collide with heavy metal targets to create a cascade of neutrons. These neutrons then cause nuclear reactions in subcritical systems.

To design these systems, complex reactor physics computer codes and highly detailed data libraries are used to compute the reactivity of systems, reaction rates, destruction rates, …

Reactor Physics Studies For The Afci Reactor-Accelerator Coupling Experiments (Race) Project, Denis Beller

Transmutation Sciences Physics (TRP)

The specific research objective of this three-year project is to design and conduct an accelerator driven experiment. This experiment will help demonstrate in the U.S. the ability to design, compute, and conduct ADSS experiments; and to predict and measure source importance, coupling efficiency, sub-critical reactor kinetics and source-driven transients. In addition, databases will be created for both steady state and transient ADSS experiments for the nuclear community to develop and test new computational codes and methods, and the importance of a driving neutron source in various regions of different subcritical assemblies will be mapped. Experiments will be conducted and compared …

Developing A Sensing System For The Measurement Of Oxygen Concentration In Liquid Pb-Bi Eutectic, Yingtao Jiang, Bingmei Fu

Transmutation Sciences Materials (TRP)

The research objectives of this project were as follows:

• To generate calibration curves of voltage versus oxygen concentration for the YSZ oxygen sensor system under various temperatures in liquid LBE.
• To determine the sensor characteristics of the YSZ sensor system.
• To determine oxygen dissolving rates in LBE under different temperatures in vitro.
• To study the effects of unwanted electrical conductivity, contributed by the mobility of the electrons at high temperatures, for more accurate oxygen measurement.
• To study alternative and promising oxygen measuring methods.

Corrosion Mechanisms And Kinetics Of Steels In Lead-Bismuth Eutectic: Quaterly Report, Allen L. Johnson, John Farley

Transmutation Sciences Materials (TRP)

A large number of studies of corroded samples were conducted using SEM, XPS, probe, and the TEM. Samples from the DELTA loop at LANL and from other sources were examined. Also, the investigation of 316 class stainless steel in LBE is continuing.

Corroded samples of D-9 steel have been in the process of being studies, which is a variant of 316 stainless steel that is optimized for resistance to swelling. The D-9 samples are notable for the process in which a localized failure of the protective oxide layer becomes widespread corrosion. The research group is examining the D-9 samples using …

Fundamental And Applied Experimental Investigations Of Corrosion Of Steel By Lbe Under Controlled Conditions: Kinetics, Chemistry Morphology, And Surface Preparation, John Farley, Allen L. Johnson, Dale L. Perry

Transmutation Sciences Materials (TRP)

Advanced nuclear processes such as the transmutation of nuclear waste, fast reactors, liquid-metal-cooled reactors, and spallation neutron sources require advanced materials systems to contain them. The required structural materials must be stable in the presence of nonmoderating coolants. A prime candidate for such a coolant is Lead Bismuth Eutectic (LBE). Materials in these systems must be able to tolerate high neutron fluxes, high temperatures, and chemical corrosion. Unfortunately, LBE corrodes stainless steel.

The corrosive behaviors of structural materials in LBE are not well understood. The Russians have over 80 reactor-years experience with LBE coolant in their Alpha-class submarine reactors. The …

Effect Of Silicon Content On The Corrosion Resistance And Radiation- Induced Embrittlement Of Materials For Advanced Heavy Liquid Metal Nuclear Systems, Ajit K. Roy

Transmutation Sciences Materials (TRP)

This task is primarily focused on the evaluation of the effect of Si content on the susceptibility of modified 9Cr-1Mo-0.24V steel to stress corrosion cracking (SCC) and localized cracking in both molten lead-bismuth eutectic (LBE) and an aqueous solution of acidic pH.

Further, significant efforts are in progress to characterize the deformation mechanism of modified T91 grade steel as a function of temperature and strain rate. Simultaneously, surface analyses of the tested materials are ongoing using state-of-the-art techniques including scanning electron microscopy (SEM) and transmission electron microscopy (TEM).

Theoretical Modeling Of Protective Oxide Layer Growth In Non-Isothermal Lead Alloy Coolant Systems, Yitung Chen, Jinsuo Zhang, Huajun Chen, Jichun Li

Transmutation Sciences Materials (TRP)

The goal of this research project is to provide a basic understanding of the protective oxide layer behaviors and to develop oxide layer growth models of steels in non-isothermal lead alloys (lead or lead-bismuth eutectic) coolant systems. Precise studies and simulations of all hydrodynamics with thermal conditions encountered in practical coolant loop systems by use of different flowing conditions in the laboratory are difficult and expensive, if not impossible. Therefore it is important and necessary to develop theoretical models to predict the protective oxide layer behaviors at the design stage of a practical lead-alloy coolant system, to properly interpret and …

Corrosion Barrier Development For Lbe Corrosion Resistance: Quarterly Report (April 2006), Biswajit Das

Transmutation Sciences Materials (TRP)

As reported in the last quarterly report, synthesis of Cr nanowires was found to be problematic in terms of uniform coverage. Hence Ni was identified as the alternative metal to form the nanowires. The purpose of the metal nanowires is to provide structural integrity to the nanoporous alumina, as well as a second defense mechanism against corrosion by oxidizing in case the top alumina layer is compromised. Nickel was selected due to its established electrochemical synthesis procedure. While Ni can provide very good structural integrity to the porous alumina, one potential problem is its higher dissolution rate in LBE. However, …