Nuclear Engineering Commons^™

Modeling, Fabrication, And Optimization Of Niobium Cavities Phase Iii: Quarterly Report, Robert A. Schill Jr., Mohamed Trabia

Transmutation Sciences Materials (TRP)

This quarterly report provides an update to the last phase of the Modeling, Fabrication, and Optimization of Niobium Cavities. Designing the experimental setup of secondary electron emission was well underway in early summer of 2003 when funding was made available for this portion the study. By March 2004, many of the components of the experimental study reached UNLV with some assembly accomplished. The first secondary electron emission (SEE) measurement was made from the surface of a Faraday cup in September 2004. At a particular beam energy, the current measured with the Faraday cup and electrometer changed sign over a range …

Design And Evaluation Of Processes For Fuel Fabrication: Quarterly Progress Report #11, Georg F. Mauer

Fuels Campaign (TRP)

The eleventh quarter of the project covered the following:

• Mr. Richard Silva successfully defended his thesis in April 2004 and graduated from the MEG Master’s program.

• Further refinements on Concepts and Methods for Vision-Based Hot Cell Supervision and control, focusing on rule-based object recognition (Ph.D. Graduate Jae-Kyu Lee). Ms. Caroline Wiejak, an exchange student from the ESIEE in Marne-la-Vallee, France is continuing with the image analysis effort. To date, she has transferred Jae-Kyu’s code to Matlab, and is presently expanding its application to more complex 3D shapes.

• Graduate student Jamil Renno refined and detailed his simulations of …

Modeling, Fabrication, And Optimization Of Niobium Cavities: Phase Iii Third Quarterly Report, Robert A. Schill Jr., Mohamed Trabia

Transmutation Sciences Materials (TRP)

Niobium cavities are important parts of the integrated NC/SC high-power linacs. Over the years, researchers in several countries have tested various cavity shapes. They concluded that elliptically shaped cells are the most appropriate shape for superconducting cavities. The need for very clean surfaces lead to the use of a buffered chemical polishing produce for surface cleaning to get good performance of the cavities. The third phase concludes the experimental a fluid flow study and optimization study. The first quarter and second quarter of phase three also begins the experimental set-up of secondary emission studies from niobium in superconducting mode. This …

An Analysis Of The Effects Of Low Energy Electron Radiation Of AlXGa1-XN/Gan Modulation-Doped Field-Effect Transistors, James M. Sattler

Theses and Dissertations

The effects of radiation on Al_xGa_1-xN/GaN MODFETs is an area of increasing interest to the USAF as these devices become developed and integrated in satellite-based systems Irradiation is also a valuable tool for analyzing the quantum-level characteristics and properties that are responsible for device operation Al_xGa_1-xN/GaN MODFETs were fabricated and irradiated at liquid nitrogen temperatures by 0,45-1,2MeV electrons up to doses of 6*10¹⁶ e/cm². Following irradiation, low temperature I-V measurements were recorded providing dose-dependent measurements Temperature-dependent I-V measurements were also made during room temperature annealing following irradiation I-V measurements …

Design And Evaluation Of Processes For Fuel Fabrication: Quarterly Progress Report #10, Georg F. Mauer

Fuels Campaign (TRP)

The tenth quarter of the project covered the following:

• Mr. Richard Silva continued the development of a simulation model with a Waelischmiller hot cell robot, and is close to completing his M.Sc. thesis project. Rich will likely defend his thesis in April 2004.

• A project review meeting with Dr. Mitch Meyer and other ANL scientists was held in December 2003 at ANL West, Idaho Falls, ID. Dr. Meyer described ANL long term research objectives with regard to transmuter fuel manufacturing.

• Further refinements on Concepts and Methods for Vision-Based Hot Cell Supervision and control, focusing on rule-based object …

Modeling, Fabrication, And Optimization Of Niobium Cavities: Phase Iii Second Quarterly Report, Robert A. Schill Jr., Mohamed Trabia

Transmutation Sciences Materials (TRP)

Niobium cavities are important parts of the integrated NC/SC high-power linacs. Over the years, researchers in several countries have tested various cavity shapes. They concluded that elliptically shaped cells are the most appropriate shape for superconducting cavities. The need for very clean surfaces lead to the use of a buffered chemical polishing produce for surface cleaning to get good performance of the cavities. The third phase concludes the experimental a fluid flow study and optimization study. The first quarter and second quarter of phase three also begins the experimental set-up of secondary emission studies from niobium in superconducting mode. This …

Modeling, Fabrication, And Optimization Of Niobium Cavities, Robert A. Schill Jr., Mohamed Trabia, William Culbreth

Transmutation Sciences Materials (TRP)

One of the key technologies for the deployment of acceleratordriven transmutation systems is the accelerator itself. Elliptical superconducting niobium cavities are used to increase the efficiency of the high-power accelerators needed to support the transmutation mission.

One of the major sources of energy loss from a superconducting accelerator cavity is a process known as multiple impacting (or “multipacting”) of electrons. This phenomenon limits the maximum amount of energy and power that the niobium cavity can store. As a result, the maximum power available for accelerating the desired charge, as well as the overall performance of the accelerator is reduced. Furthermore, …