Nanoscience and Nanotechnology Commons^™

The Electrocatalystic Investigation Of 3,4-Dihydroxybenzoic Acid On The Modified Multiply Wall Carbon Nanotubes, Ming-Qi Li

Journal of Electrochemistry

The electrochemical behavior of 3,4-Dihydroxybenzoic acid(DHBA)on modified multiply wall carbon nanotubes electrode was investigated by cyclic voltammetry(CV) and square wave voltammetry(SWV).Results show that in 0.1 mol/L HCl solutions the modified carbon nanotube electrode has an obvious electrocatalytic effect on the oxidation and deoxidization of DHBA.The oxidation current of DHBA is linear to it's concentration in the range of 4.0×10~(-6)～1.0×10~(-4) mol/L and 2.0×10~(-4)～8.0×10~(-4)1mol/L with correlation coefficient of 0.9995 and 0.9992.The detection limit is 1.0 ×10~(-6)mol/ L.

The Research Of Nano-Sized Nio Anode Materials For Lithium Ion Batteries, Jun-Mei Yan, Jing Zhang, Yong Yang

Journal of Electrochemistry

The nano-sized NiO materials were synthesized by solid phase method and sol-gel method. The synthesis conditions were optimized by DSC and TG techniques. The sol-gel method was optimized by changing the solvent and regulating the solution's pH for preparing NiO material. The structure and morphology of the materials were also characterized by means of XRD and TEM techniques, and the electrochemical performances of the materials were studied by the galvanostatically charge and discharge experiments.

Cyclic Voltammetry And Surface Enhanced Raman Spectroscopy Of Dissociative Adsorption Of Ethanol On Pt-Ru Electrodes, Zhang Bin

Journal of Electrochemistry

The behaviors of dissociative adsorption of ethanol on roughened platinum-ruthenium electrode with high activity of SERS were studied by using cyclic voltammetry and in-situ surface enhanced Raman spectroscopy, surface enhanced Raman spectra of dissociative adsorption of ethanol on Pt electrode in acid was obtained for the first time. It is shown that the Pt-Ru could lower the over-potential of CO oxidation when compared to Pt electrode. The results show that the ethanol in acid medium can be self-dissociated at Pt-Ru electrode to produce CO, which discourage the further oxidation of ethanol, some information of Pt-C and Pt-C-Pt stretching vibration from …

Surface-Enhanced Raman Spectra Of Cytosine Adsorbed On A Roughened Gold Electrode, Yuan-Fei Wu, Jian-Feng Li, De-Yin Wu, Bin Ren, Zhong-Qun Tian

Journal of Electrochemistry

Cytosine adsorbed on a roughened gold electrode has been investigated by using electrochemical cyclic voltammetry and surface-enhanced Raman spectroscopy (SERS). The results indicate that cytosine was adsorbed on the Au electrode in a perpendicular orientation via the N3 position. As the maximum enhancement of ring breathing mode appears at negative potentials compared with other modes, both the electromagnetic enhancement and the charge transfer mechanism were considered to contribute to the SERS intensity. The binding interaction between cytosine and the gold electrode was weakened when the potential was negatively moved. The result also indicates that the SERS technique can be used …

Electrocatalytic Oxidation And Degration Of Active Red X-3b By Nanotubes Catalytic Electrodes, Yi Wen, Jian-Hui Fang

Journal of Electrochemistry

The catalytic splitting decomposition of carbon nanotubes isprocessed by dispersing with dilute nitric acid and thermal oxidation. Then well-proportionedphenolic resin is mixed in the carbon nanotubes. Then, the carbon nanotubesare made into electrodes by hot-press molding after the process of milling with high speed. The surface of the carbon nanotubes electrodes is analyzed by SEM. Active red X-3B simulated waster water is disposed by carbon nanotubes catalyticelectrode (anode) and stainless steel(cathode). The influencing factors of degradation by current density, concentrationof electrolyte, systemtemperature and pH are investigated. The experimental results indicated that acidiccondition is propitious tothe degradationreaction of organicdyestuff and wastewater …

Surface And Sructure Investigations Of Membrane Electrode Assembly In Dmfc Lifetime Testing~*, Chengxuan Chengxuan, Cheng Peng, Meng-Di You, Jing Liu, Ying Zhang

Journal of Electrochemistry

The lifetime and performance of a direct methanol fuel cell (DMFC) were investigatedto understand the correlation between thestructure of catalysts /membrane and cell performanceversus time.The cell polarization and performance curves were obtained during the DMFC operation with the time.The catalysts and Nafion~ membrane of the membrane electrode assembly (MEA) from the lifetime test were comprehensively examined by XRD, HRTEM, FTIRand Raman spectroscope techniques.The results revealed that there was significant performance degradation during the first 200 hours operation; while the degradation was slowing down between 200 and 704hours operation.The degradation became worse after 1 002 h operation.The increases of the catalyst …

The Application Of Astm C1202-93 On Evaluating The Performance Of Anti-Corrosion Of Concrete, Yuan Chen Yuan

Journal of Electrochemistry

The test of chloride ion penetration based on the standards of ASTM C1202-93 is applied to evaluate the anti-corrosion performance of concrete in this research. Concrete specimens were produced according to ACI 318-89 mixture proportioning design and the Desenfied Mixture Design Algorithm (DMDA) and were measured the 6-hour coulombs at the age of 91 days. Results show that w/b is not the factor influencing chloride penetration of ACI concrete, as the ion penetration of ACI specimens is all higher than 2 000 Coulombs and can even be poorer than 10 000 Coulombs. With a proper amount of pozzolanic material, the …

Preparation, Characterization And Electrochemical Properties Of Nano Tio_(2)-Cnt-Pt On Ti Substrate Complex Electrode, Dao-Bao Chu

Journal of Electrochemistry

The nanoTiO_(2)-CNT-Pt on Ti substrate complex electrodes were prepared from precursor of (Ti(OEt)_(4)) directly hydrolyzed and by cyclic voltammograms electroplating method . The XRD and SEM results showed that the nano TiO_(2) (anatase) particle sizes ranged 5~10 nm and the Pt nanoparticle (average size 9nm) dispersed uniformly on nanoTiO_(2)-CNT film surface. The electrocatalytic activity of Ti/nanoTiO_(2)-CNT-Pt electrode was investigated by cyclic voltammetry and chronopotentiogram. The results indicated that the Ti/nanoTiO_(2)-CNT-Pt electrode exhibited very high electrocatalytic activity and stability for the electro-oxidation of methanol at room temperature. When Pt loading was 0.32 mg/cm~(2), the oxidation peak current of methanol was 480 …

Using Electrodeposition To Fabricate Mould For Polymer Microfluidic Chip, Luo Yi

Journal of Electrochemistry

Many researches have been focused on polymer microfluidic chip in recent years and the mould plays an important role in its fabrication process. Using electrodepositingmethod to fabricate a metal mould for polymer microfluidic chip has been presented in this paper. An ultra-thick photoresist SU-8 was coated on a pretreated metal plate, after photolithography, nickel was electrodeposited in the patterned SU-8, then was removed the SU-8 to obtain a final metal mould. This methodreduces workload of electrodeposit largely. Applying counter current before deposit, adding additive to solution and vacuum anneal after demould have been used to improve the binding force between …

The Fabrication And Electrochemical Studies On Carbon Nanotube Array Electrodes, Quan-Yong Gao, Jing Zhang, Yangyong Yangyong

Journal of Electrochemistry

An improved technique for fabrication of carbon nanotube array electrodes has been proposed in this work. Firstly, carbon nanotubes (CNs) array electrodes were prepared by combsination of Chemical Vapor Decomposition (CVD) method and sputtering techniques in anodized aluminum oxide (AAO) membrane. The CNs/AAO was immersed into HF solution to remove the barrier layer. Controlling the immersing time, the CNs array electrodes with different length contacted with electrolyte can be prepared. The morphology of CNs array electrodes was observed by SEM. The electrochemical properties of CNs array electrodes were investigated by cyclic voltammetry and electrochemical impedance spectroscopy. Cyclic voltammetric curves of …

Corrosion Barrier Development For Lbe Corrosion Resistance, Biswajit Das

Transmutation Sciences Materials (TRP)

In the last quarter, a specialized sample holder was developed for the anodization of alumina on steel. In addition, it was determined that oxalic acid was the most appropriate acid for the anodization of these structures. The steel samples obtained from LANL were first cut into a number of pieces, each measuring 11mm x 8mm x 1.6mm, to allow multiple experiments. Special care was taken to ensure that the cutting process did not damage the samples. After investigation of several techniques, including laser cutting, the samples were cut using EDM wires. The cut steel pieces did not show any damage …

Corrosion Barrier Development For Lbe Corrosion Resistance: Quaterly Report, Biswajit Das

Transmutation Sciences Materials (TRP)

With the demonstration of formation of nanoporous alumina on steel and its good adhesion to substrate under thermal cycling, the next project task was to synthesize Chromium nanowires inside the alumina pores. During the previous quarter, a specialized sample holder was developed towards this goal. Various techniques for the deposition of Chromium were investigated and electro-deposition was determined to be the most suitable approach due to the large aspect ratio of the pores. A challenge in using electro-deposition for porous alumina is the potential sealing of the pores in aqueous solutions at higher temperatures. To avoid this problem, a search …

Development Of Nanostructure Based Corrosion-Barrier Coatings On Steel For Transmutation Applications, Biswajit Das

Transmutation Sciences Materials (TRP)

Advanced transmutation systems require structural materials that are able to withstand high neutron fluxes, high thermal cycling, and high resistance to chemical corrosion. The current candidate materials for such structures are ferritic and ferritic-martensitic steels due to their strong resistance to swelling, good microstructural stability under irradiation, and the retention of adequate ductility at typical reactor operating temperatures.

In parallel, lead bismuth eutectic (LBE) has emerged as a potential spallation target material for efficient production of neutrons, as well as a coolant in the accelerator system. While LBE has excellent properties as a nuclear coolant, it is also highly corrosive …

Boron-Rich Semiconducting Boron Carbide Neutron Detector, Andrew D. Harken, Ellen E. Day, Brian W. Robertson, Shireen Adenwalla

Shireen Adenwalla Papers

Data on the neutron detection capabilities of a variety of boron carbide/Si heterojunction diodes is presented. The pulse height spectra are compared with previously measured conversion layer devices and the variations in shape and position of the peaks are discussed.

Modeling And Simulation To Investigate Effects Of Static Mixer, Carrier Gas, Temperature And Pressure On The Mixing Ratio Of Carbon Nanotubes Growth Reactors, David Addie Noye

Dissertations and Theses @ UNI

The problem of this study was to investigate the effects of static mixer, carrier gas, carrier gas inlet pressures, and reactor operating temperatures on the mixing ratio of carbon nanotube synthesizing reactor. The methodology included design of static mixers, mathematical modeling, and computer modeling and simulation experiments.

The simulation experiment was performed based on single phase carrier gas modeling due to difficulty and time for three phase fluid modeling. First only nitrogen carrier gas in addition to the other three factors under constant inlet flow velocity and inlet temperature was simulated. Secondly, the same procedure was applied to argon carrier …