Open Access. Powered by Scholars. Published by Universities.®

Nanoscience and Nanotechnology Commons™

Open Access. Powered by Scholars. Published by Universities.®

Environmental Engineering

Institution
Keyword
Publication Year
Publication
Publication Type
File Type

Articles 61 - 69 of 69

Full-Text Articles in Nanoscience and Nanotechnology

Diagnostic Of Critical Circuits Of Kraft Pulp Production Process Considering The Environmental Aspects, João F. Gomes Jan 2002

Diagnostic Of Critical Circuits Of Kraft Pulp Production Process Considering The Environmental Aspects, João F. Gomes

João F Gomes

This paper describes systematic work done in the field of atmospheric emissions from Portuguese Kraft pulp mills. This study led to the determination of emission factors from stationary sources that proved to be an important tool to assess the need for investment on air pollution abatement equipment, namely in what concerns mal-odorous gases.

Go to article

Characterisation Of Non-Condensable Sulphur Containing Gases From Kraft Pulp Mills (2), João F. Gomes Jan 2001

Characterisation Of Non-Condensable Sulphur Containing Gases From Kraft Pulp Mills (2), João F. Gomes

João F Gomes

This paper describes work performed on the sampling and analysis of non-condensable gases (NCG) emitted from diffuse sources of a Portuguese Kraft pulp mill, which is the background information for a NCG collection, treatment and disposal system. The variability found in the composition of the gaseous compounds showed the existence of gaseous streams other than typical total reduced sulphur (TRS) compounds as usually described. From the measured TRS concentrations and the gas flow rate from each source it was possible to calculate the emission flow rate, E, of each source. These emission flow rates were then divided into 3 categories …

Go to article

Practical Determination Of Efficiency Of Electrostatic Precipitators, João F. Gomes Jan 1999

Practical Determination Of Efficiency Of Electrostatic Precipitators, João F. Gomes

João F Gomes

Electrostatic precipitators are one of the most efficient particulate pollution control equipments used mainly for the treatment of gaseous effluents at high flow rates. Consequently electrostatic precipitators are widely used in thermal power plants, cement plants and pulp mills. Apart from a high efficiency other advantages are related with the fact that this type of equipment has a considerable low payback time in industrial plants where the particulate recovered from the gases has commercial value and can be recycled within the industrial process itself or even sold to other industrial companies. Where sulphate (Kraft) pulp mills are concerned an electrostatic …

Go to article

Characterisation Of Non-Condensable Sulphur Containing Gases From Kraft Pulp Mills, João F. Gomes Jan 1998

Characterisation Of Non-Condensable Sulphur Containing Gases From Kraft Pulp Mills, João F. Gomes

João F Gomes

This paper describes work performed on the sampling and analysis of non-condensable gases (NCG) emitted from diffuse sources of a Portuguese kraft pulp mill, which is the background information for a NCG collection, treatment and disposal system. The variability found in the composition of the gaseous compounds showed the existence of gaseous streams other than typical total reduced sulphur (TRS) compounds as usually described.

Go to article

A Simple Way To Measure Particle Size, João F. Gomes Jan 1998

A Simple Way To Measure Particle Size, João F. Gomes

João F Gomes

The size range of particles is an important parameter for subsequent dispersion estimates and sometimes is quite useful for analysing the performance of combustion equipment as well as dedusting equipment efficiency. So far, no standard method has been developed but several laboratories use laser-beam techniques which are usually quite expensive ones. In this paper a method is presented where the particles are collected isokinetically in a filter from gases circulating in a stack as described in USEPA method 5. Afterwards particles are observed at an optical microscope and measured. In spite of some limitations this appears to be an inexpensive …

Go to article

Assessment Of Opacimeter Calibration On Kraft Pulp Mills, João F. Gomes Dec 1997

Assessment Of Opacimeter Calibration On Kraft Pulp Mills, João F. Gomes

João F Gomes

This paper describes the methodology and specific techniques for calibrating automatic on-line industrial emission analysers, specifically equipments that measure total suspended dust installed in pulp mills within the scope of Portuguese Regulation Nº 286/93 on air quality. The calibration of opacimeters is a multi-parameter relationship instead of the bi-dimensional calibration which is used in industrial practice. For a stationary source from a pulp mill such as the recovery boiler stack, which is subjected to significant variations, the effects of parameters such as the humidity and gas temperature, deviations on isokinetism, size range of particles and characteristic transmitance of equipment are …

Go to article

Pollutant Atmospheric Emissions From Portuguese Kraft Pulp Mills, João F. Gomes Jan 1997

Pollutant Atmospheric Emissions From Portuguese Kraft Pulp Mills, João F. Gomes

João F Gomes

This paper describes systematic work done in the field of atmospheric emissions from Portuguese Kraft pulp mills. This study led to the determination of emission factors from stationary sources that proved to be an important tool to assess the need for investment on air pollution abatement equipment.

Go to article

Notice On A Method For Measuring Size Range Of Particles In Gases From Stationary Sources, João F. Gomes Jan 1990

Notice On A Method For Measuring Size Range Of Particles In Gases From Stationary Sources, João F. Gomes

João F Gomes

No abstract provided.

Go to article

Program Calculates Critical Properties, João F. Gomes Jan 1988

Program Calculates Critical Properties, João F. Gomes

João F Gomes

No abstract provided.

Go to article

First Prev