Manufacturing Commons^™

Rc Baja: Drivetrain And Steering, Mathew Morgan

All Undergraduate Projects

The RC Baja competition is a contest where undergraduate mechanical engineering students design, build, and compete against one another. The objective of this competition is to create the most efficient RC car possible. A gear train analysis was done and showed an 8:1 gear ratio would be the most efficient ratio due to the chosen motor having a higher torque output. Also, a stress analysis was done and showed that 2011 T3 aluminum passed the stress and weight criteria. These analyses ensured the RC Baja car was efficient. Most of the parts for the drivetrain and steering subassemblies were machined …

R/C Baja: Drivetrain, Connor T. Donovan

All Undergraduate Projects

The Central Washington University Mechanical Engineering Technology Department hosts an annual R/C Baja competition in which R/C cars fabricated by student teams are put through a series of courses and tests to determine which team's vehicle is best. The goal of this project was to create a functioning drivetrain that conveys power from the battery to the wheels and provides control of the vehicle. A list of requirements for the drivetrain was created to ensure that the vehicle will not only function, but that it will actually succeed in the competition. These requirements included that the vehicle must achieve a …

Team H&H Rc Baja Drivetrain, William T. Hedlund

All Undergraduate Projects

A need for a drivetrain and steering system that could provide locomotion and directional control for the H&H RC Baja racecar was needed. The RC Baja event is a competition hosted by the CWU ASME club in which teams of engineering students compete against each other to test the effectiveness of the respective designs. The car needed to be able to compete in three events: a drag race, solemn course, and a Baja event. This was accomplished by designing and manufacturing several parts of different materials utilizing a range of manufacturing techniques to produce sub-assemblies and that made up the …

Jcati Carbon Fiber Recycler: Oven Enclosure, Margarita Romero

All Undergraduate Projects

Central Washington University partners with Boeing and is funded by the Joint Center of Aerospace Technology Innovation (JCATI) to develop a mechanism that takes carbon fiber wing trimmings from Boeing that are resin coated and recycles carbon fiber. This is done by crushing the wing trimmings and then putting it into a 500°C oven to melt off the resin. This project focuses on the enclosure for the oven and making sure precautions are met such as having the outside surface be less than 45c through heat transfer analysis, argon fills enclosure in 13 minutes through fluid dynamics analysis, and 99% …

R/C Baja Truck Suspension, Chassis And Steering, Ryan Lafrombois

All Undergraduate Projects

The ASME RC Baja Challenge is an annual competition that the Central Washington University Mechanical Engineering and Technology (MET) department takes part in. Senior level engineers divided the work between the drivetrain and the chassis/suspension while designing and manufacturing to meet a set of requirements. Next, a device was to be developed to be able to withstand the extreme forces to be successful in the competition at the end of the year. The process would require that the students use their acquired knowledge and skills to design, manufacture, and analyze a capable device. Designing involved the completion of 12 analyses …

Carbon Fiber Recycling: Delamination System, Aaron Eastman

All Undergraduate Projects

The production of composite wings at Boeing causes carbon fiber waste and CWU Mechanical Engineering Technology students have been tasked in designing a carbon fiber recycling system. This project was brought forth and funded by the Joint Center for Aerospace Technology Innovation (JCATI). There are three subsystems that make up the carbon fiber recycling system, the delamination system, shredding system, and the oven. The purpose of this project was to increase the efficiency and effectiveness of the delamination system of the carbon fiber recycling system. The old system reached approximately 30-40 percent delamination with one pass through the system, and …

Jcati Carbon Fiber Shredder 2022, Parker Sudderth

All Undergraduate Projects

This project is a potential solution to keep the carbon fiber waste from airplane manufacturing to a minimum, sponsored by the Joint Center for Aerospace Technology Innovation (JCATI). The design and assembly will be scalable for future industry application. The overall design of the whole carbon fiber recycler consists of a crusher, shredder, and oven. This report is on the caron fiber shredder module. The shredder is tasked with being able to shred the delaminated carbon fiber scrap that directly comes from the crusher. The operation must produce shreds in the proper size to be gathered and delivered to the …

Asme Rc Baja Racer, Chesna Kern

All Undergraduate Projects

The American Society of Mechanical Engineers (ASME) holds a competition at their annual conference for college students to design an RC car that will compete in sprint, slalom, and obstacle course races. The RC Baja car was designed to complete every event in the competition with a focus on the obstacle course due to the anticipated impacts inflicted on the project car by jumps and other obstacles. The project was a collaborative effort. This presentation focuses on the chassis and suspension while Gizan Gando will present about the drivetrain. The drop and frontal impact test requirements guided the design process …

Hydraulic Balsa Wood Rising Bridge, Kaitlyn Greenfield

All Undergraduate Projects

What is the solution to allowing tall vessels to navigate past a vehicle bridge that is less than 10 [ft] above the water? To answer this question, a balsa wood bridge was designed, constructed, and tested. The bridge needed to articulate by mechanical means, allow for travel through the bridge, and be able to withstand ample force while the main structure only being constructed of balsa wood and glue. The project was analyzed in sections. These sections include: the bridge structure and its members, the hydraulic lift, and the pins needed for the bridge and hydraulic lift to operate. The …

Jcati Base Plate, Jacob Atamian

All Undergraduate Projects

Students of the Mechanical Engineering Technology (MET) program at Central Washington University have contributed to an ongoing Carbon Fiber Recycler project funded by the Joint Center for Aerospace Technology Innovation (JCATI). The goal of this project was to modify the existing recycling system to produce a higher success rate of recycled carbon composite material. This report focuses on increasing the rigidity of the crushing gears so that the deflection occurring among the components during operation was below 0.005 inches to ensure proper operating conditions. The operating speed of the crushing gears was 2.5 rpm with a crushing load of 10,500 …

Mini Rc Baja Car, Jason Schindler

All Undergraduate Projects

Incorporating each aspect of engineering incorporated into a senior project is difficult. That is why an RC Baja car is a great senior project for Mechanical Engineering students. The approach that students must take to design, construct, and test the car is to set parameters, and to make overall goals that can be easily measured. These goals include, but not limited to things like a $700 budget and the ability to withstand a 1-foot drop to a flat surface on all four wheels simultaneously. First, the design must meet the specifications and rules that are set previously. This ensures that …

Balsa Wood Bridge, Anndie Watterson

All Undergraduate Projects

A model for a strong bridge that could span a set distance and rise up to allow for passage underneath was requested, and specifications for the design were given. The model bridge was designed out of balsa wood to meet all the requirements. Using structural and material analysis and simple mechanical designs, a bridge was designed and constructed out of balsa wood, wood glue, and metal components used for articulation that met all of the criteria set by the assigner. The bridge was tested to ensure all specifications were met. The resulting bridge can hold 20kg of weight suspended from …

Balsa Wood Bridge, Andrew Harris

All Undergraduate Projects

Faculty at Central Washington University proposed a challenge to mechanical engineering students that could be accomplished in an in-home setting. The goal was to create a balsa wood bridge, weighing no more than 85 grams, that can support a load over an open span and raise above its resting position by means of a mechanical system. To produce a successful solution to the problem, a vertical lift bridge was created consisting of two lifting towers and a load bearing bridge. Using equations of static equilibrium and strength of materials, the required width for each member was determined. Project requirements were …

Asme Rc Baja Car Drivetrain, Gizan G. Gando

All Undergraduate Projects

The purpose of the RC Baja Car is to compete in the American Society of Mechanical Engineers (ASME) competition, a series of events to prove the functionality of the vehicle. This series of events includes the Slalom, Drag, and Baja race. The Slalom is a test in the steering capability of the car. The Drag is a test in the acceleration of the car in a straight line. Lastly, the Baja puts all factors together in a race to test every component of the car. This project is about building an RC car that can function under these conditions and …

Next Generation Longboard Trucks Ng-Trucks, Zach J. Ducatt

All Undergraduate Projects

A device is needed that will provide longboard riders with a truck that is specifically designed for the sharp turns and high speeds they experience throughout their ride. This longboard truck must have a design that is engineered for these purposes and avoids the standard pin and bushing design that is commonly copied from the closely related skateboard truck. This standardized design is outdated, and more importantly, was made to adhere to the skateboard style of riding, consisting primarily of performing tricks with less turning. The longboard truck provides a secure connection point upon the two wheels and the board …

Forge Burner, Caleb Desjardins

All Undergraduate Projects

Can small scale blacksmithing operations achieve a level of efficiency in their forge comparable to that of a large scale industry? The causes for the lack of efficiency needed to be pinpointed, and then the geometry of the existing design for the burner could be changed to fix the underlying issues, while still maintaining functionality. The problems with the previous design is the geometry of the intake giving an unknown air/fuel ratio, and the attachment of to the forge allowing the intake air to be contaminated by exhaust gasses. A burner needed to be designed that would solve these problems …

Asts Frame, Dustin Braun

All Undergraduate Projects

The automotive industry has been an industry of many breakthroughs in technology and mechanical systems over the course of its history. But in one area, its innovation has slowed. That is in the area of the short throw shifter. All aftermarket short throw shifters are currently one dimensional. No adjustability, no ability to finetune to one’s personal desire. The goal of this project is to create a short throw shifter frame that is easier/faster to install, as well as allow for full adjustability of the shifter from inside the car. This frame design uses mostly 6061-T6 aluminum, along with some …

R/C Mini Baja Car: Drive Train And Steering, Carlton R. Mcdonald

All Undergraduate Projects

The purpose of the Baja R/C Car is to compete in the ASME eFX competition in a series of events to prove the functionality of the vehicle. This series of events includes the Slalom, Drag, and Baja race, The Slalom is a test in the steering capability of the vehicle, the Drag is a test in the acceleration of the vehicle in a straight line, and the Baja puts all factors together in a race to test every component of the vehicle. This project is about building an R/C car that not only functions, but also has maximum performance capabilities …

Rc Mini Baja Car - Suspension And Chassis, Collin Mckenzie

All Undergraduate Projects

Two students have developed a unique design of the RC Baja Car to optimize functionality and performance. A Baja car is a remote controlled 1/10 scale car that is used for recreation or competition, usually meant for competing in the ASME Baja car competition versus various schools. The competition focuses on the best time achieved in different courses that utilize speed, turns, and jumps. The objective for the project was to create a unique suspension from previous individual’s projects by creating a four-link suspension in which allows more travel in the suspension of the car and maintains functionality with the …

Speed Bump Power Generator, Sultan Alanazi, Osamah Abulgaith

All Undergraduate Projects

A large amount of energy is wasted by the vehicles on the speed breakers through friction. Energy can be produced by using the vehicle weight and speed. The team proposes a smart speed breaker that generates power (Speed bump power generator). The device allows vehicles to pass from both sides. The system makes use of mechanical assembly with metal sheets with linkages that press down with spring arrangement. Using the motion and weight of vehicles was the method that the team relied on to design the device. The mass of the vehicles allows the top plate to move the rack …

Composite Guitar, Ryn Rollins

All Undergraduate Projects

Traditional wood-bodied products such as boats, hockey sticks, and guitars can be easily chipped or cracked if not properly taken care of. The wood can absorb moisture and deteriorate over time. If that wood is replaced with composite materials, those products can become stronger, more lightweight, and resistant to temperature and corrosion. Two of the most popular composite materials are carbon fiber and fiberglass. Because these composite materials have such a high strength, the core of a guitar body can also be replaced with a lighter material such as Styrofoam which makes for a lighter and more durable guitar. The …

Ev Clutch System, Jacob Yordy

All Undergraduate Projects

This project’s goal was to add a clutch system to an electrical vehicle at Central Washington University. The project’s second goal was to have the clutch system improve the electrical vehicle’s fuel economy for Electrathon events. Electrathon uses an equivalent mpg formula to determine an electrical vehicle’s “fuel economy.” Based on the amount of energy in kilo-Watt hours in a gallon of gas, Electrathon assumes each car uses 0.026 gallons of “gas” in the hour long race and the mpg value given to an electrical vehicle is based on the distance the vehicle travels in the race. Analyzes and problem …

Mechanical Footstep Power Generator, Mohammed Saleh Aljohani, Faisal Alonazi

All Undergraduate Projects

Mechanical Footstep Power generator

By Author: Mohammed Aljohani

Abstract

Modern technology is focusing on newer and better sources of energy. Among the important areas are power generation methods since electricity has become part of our lives. Various researchers have conducted surveys to find out the feasibility of converting renewable kinetic energy into electricity. Some of the works done in the past emphasized the selection of suitable materials and power generation systems designs that appear complicated and expensive. To ensure there is cost efficiency and energy efficiency better power generation systems need to be embraced.

The footstep power generator is a …

The Bracket, Ryan Jerome Skerbeck

All Undergraduate Projects

• Abstract
• Bracket, casting, aluminum; if any of these for mentioned words interest you in anyway this is a document that you should read.
• There is a need for a compressor to be mounted to the front of a Cummins engine so that compressed air would be available on a work truck. The York compressor and the engine were known quantities, so what this project covered was the bracket that mounted the compressor to the engine and the manufacturing processes. The process chosen to make the bracket was aluminum casting; casting was chosen because of the ease of making many parts …

Carbon Fiber Recycler : Fiber Reclaimer, Alexander Edwards

All Undergraduate Projects

Boeing uses composite components for the 777x aircraft. The production of composite parts results in flashing (excess material) that must be trimmed and "thrown away" as scrap. Boeing is investigating means of recycling these scraps. The method proposed for this project is to delaminate and shred the composite material. The delamination process uses a ram to press two claw shaped devices together that bends and deforms the material in opposite directions. The chipper process uses counter rotating saw blades spaced 1/8” apart to produce small shredded material. This shredding material is pyrolyzed (heated) to decay the resin leaving the carbon …

Stair Climbing Hand Truck, James Mcpherson

All Undergraduate Projects

Abstract

Getting a heavy object up a flight of stairs usually requires a team of two or more people. Even with a team of people, the task is often still difficult, dangerous, and possibly insurmountable by one person. This problem is especially prevalent in for those who are moving into apartment complexes. Most apartment complexes have many buildings with two or more floors of living quarters, and elevators are often missing. This project sought to offer a solution to this problem. The solution in question; a motorized hand-truck with 2, trigonal planar pinwheels in place of the stock wheels. The …

Custom Foot Prosthetic: Diabetic Care, Chandler Streuli

All Undergraduate Projects

Across the United States there are people every day who lose their toes to diabetes or to loss of circulation within their legs. The problem becomes building a more cost effective and efficient prosthetic for these individuals. The prosthetics that are used for medical purposes are often costly, especially without the help of insurance. The new prosthetic was designed to be taken in and out of shoes so that it is fast and easy for the user to move the device from shoe to shoe. The manufacturing method for this project was using a 3D printer to build the initial …

Autojack - Hydraulic Powertrain System, Tyce Vu

All Undergraduate Projects

A primary problem for mechanics and automotive enthusiasts is the risk associated with lifting and securing a vehicle with conventional jack stands. Often times, improper jack-stand installation results in the vehicle collapsing unexpectedly, causing injury and/or death. This problem can be minimized through the application of a newly re-designed vehicle lifting system. The conventional method for lifting cars is time consuming and can be unsafe in many circumstances. A better, safer, and more efficient lift design was needed; the AutoJack. The approach of the AutoJack design was entirely focused on the safety of lifting a vehicle. Safety was improved by …

Medallion Manufacturing, Luis Perez

All Undergraduate Projects

A more efficient manufacturing process is needed to create the approximately 30 MET medallions, given to the graduating class. The process must be repeatable, consistent, and efficient. The objective is to create a method that can remain the same year to year, save time, and be repeated by anybody. Two approaches were developed: a casting method, and a machining method involving a computer numerically controlled (CNC) mill. The casting method began with a match plate was developed by attaching 3D printed models and runners to plywood. The design was evaluated before the pour using SolidCast software. Special attention was directed …

Electrathon: Body, Ryan Shiner

All Undergraduate Projects

• The Electrathon Vehicle project is an ongoing project that dates back to 2012. This vehicle will be raced at events to see how many laps it can complete on a single battery charge. The existing body for the Central Washington University Electrathon vehicle required modifications to fit over the current frame. These modifications were required because the rear suspension design had changed. The rear panel of the body interfered with the rear suspension. Using a rotary cutting wheel, the panel was slotted so the body could slide over the suspension and drive chain. Additionally, spacers for various sizes were needed …