Applied Mechanics Commons^™

Jcati Carbon Fiber Shredder 2022, Parker Sudderth

All Undergraduate Projects

This project is a potential solution to keep the carbon fiber waste from airplane manufacturing to a minimum, sponsored by the Joint Center for Aerospace Technology Innovation (JCATI). The design and assembly will be scalable for future industry application. The overall design of the whole carbon fiber recycler consists of a crusher, shredder, and oven. This report is on the caron fiber shredder module. The shredder is tasked with being able to shred the delaminated carbon fiber scrap that directly comes from the crusher. The operation must produce shreds in the proper size to be gathered and delivered to the …

Jcati Base Plate, Jacob Atamian

All Undergraduate Projects

Students of the Mechanical Engineering Technology (MET) program at Central Washington University have contributed to an ongoing Carbon Fiber Recycler project funded by the Joint Center for Aerospace Technology Innovation (JCATI). The goal of this project was to modify the existing recycling system to produce a higher success rate of recycled carbon composite material. This report focuses on increasing the rigidity of the crushing gears so that the deflection occurring among the components during operation was below 0.005 inches to ensure proper operating conditions. The operating speed of the crushing gears was 2.5 rpm with a crushing load of 10,500 …

The Limits & Effects Of Draw On Properties And Morphology Of Pan-Based Precursor And The Resultant Carbon Fibers, Sarah Edrington

Theses and Dissertations--Mechanical Engineering

The process, structure, and property relationship of PAN fiber as a precursor to carbon fiber was studied. The limitations of stable spinning and property improvement associated with hot draw in solution spinning were found and quantified. Conditions were varied to generated precursor fiber up to the limit of draw, from which actual samples were collected for thermal conversion to carbon fiber. Samples of PAN and subsequent carbon fiber were characterized using tensile testing and x-ray analysis. The effects of draw on modulus and break stress, as well as the orientation of the crystalline structure of both parent precursor and resultant …

Ultra-Light Bear Canister, Naveen Beasley, Eli Rogers, Cory Wilson, Donald Wood

Mechanical Engineering

A bear canister is the primary tool used by outdoor enthusiasts to protect their food from bears while camping or backpacking. There are many effective products currently on the market, however many are not designed with reduced weight in mind. Hardcore backpackers want to have the lightest gear possible to ease the strain of carrying a large pack for sometimes weeks at a time.

Current bear canisters exist that utilize carbon fiber for weight reduction, however they rely on stock carbon tubes and lack engineering analysis, and no competitor has a fully composite bear canister available. Our sponsor, Nick Hellewell, …

Finite Element Modeling Of Delamination Damage In Carbon Fiber Laminates Subject To Low-Velocity Impact And Comparison With Experimental Impact Tests Using Nondestructive Vibrothermography Evaluation, George Rodriguez Iv

Master's Theses

Carbon fiber reinforced composites are utilized in many design applications where high strength, low weight, and/or high stiffness are required. While composite materials can provide high strength and stiffness-to-weight ratios, they are also more complicated to analyze due to their inhomogeneous nature. One important failure mode of composite structures is delamination. This failure mode is common when composite laminates are subject to impact loading.

Various finite element methods for analyzing delamination exist. In this research, a modeling strategy based on contact tiebreak definitions in LS-DYNA^®was used. A finite element model of a low-velocity impact event was created to …

Biaxial & Twist Testing Of Composite Carbon-Fiber Sandwich Panels For Automotive Racing Vehicles, Erik Eckberg

Materials Engineering

Composite sandwich panels were constructed with 4-ply plain weave carbon-fiber/epoxy face sheets in the 0^o/45^o/0^o/45^o orientation and 1/8^th inch Nomex honeycomb core. The panels were cut into 5-inch square test plates for mechanical testing. All testing was done on a fixture designed and fabricated by Pratt & Miller Engineering and installed on an Instron testing system at Cal Poly. The twist test was performed by supporting diagonal corners of the plate while simultaneously loading the opposite two corners at a crosshead rate of .06 in/min (ASTM 3044-94R11). Out of 10 panels tested, …