Open Access. Powered by Scholars. Published by Universities.®
- Discipline
Articles 1 - 4 of 4
Full-Text Articles in Applied Mechanics
Strain Energy And Lateral Friction Force Distributions Of Carbon Nanotubes Manipulated Into Shapes By Atomic Force Microscopy, Mark C. Strus, Roya R. Lahiji, Pablo Ares, Vincente Lopez, Arvind Raman, Ron R. Reifenberger
Strain Energy And Lateral Friction Force Distributions Of Carbon Nanotubes Manipulated Into Shapes By Atomic Force Microscopy, Mark C. Strus, Roya R. Lahiji, Pablo Ares, Vincente Lopez, Arvind Raman, Ron R. Reifenberger
Other Nanotechnology Publications
The interplay between local mechanical strain energy and lateral frictional forces determines the shape of carbon nanotubes on substrates. In turn, because of its nanometer-size diameter, the shape of a carbon nanotube strongly influences its local electronic, chemical, and mechanical properties. Few, if any, methods exist for resolving the strain energy and static frictional forces along the length of a deformed nanotube supported on a substrate. We present a method using nonlinear elastic rod theory in which we compute the flexural strain energy and static frictional forces along the length of single walled carbon nanotubes (SWCNTs) manipulated into various shapes …
Nanoindentation Of The A And C Domains In A Tetragonal Batio3 Single Crystal, Young-Bae Park, Matthew J. Dicken, Zhi-Hui Xu, Xiaodong Li
Nanoindentation Of The A And C Domains In A Tetragonal Batio3 Single Crystal, Young-Bae Park, Matthew J. Dicken, Zhi-Hui Xu, Xiaodong Li
Faculty Publications
Nanoindentation in conjunction with piezoresponse force microscopy was used to study domain switching and to measure the mechanical properties of individual ferroelectric domains in a tetragonal BaTiO3 single crystal. It was found that nanoindentation has induced local domain switching; the a and c domains of BaTiO3 have different elastic moduli but similar hardness.Nanoindentationmodulus mapping on the a and c domains further confirmed such difference in elasticity. Finite element modeling was used to simulate the von Mises stress and plastic strain profiles of the indentations on both a and c domains, which introduces a much higher stress level than …
Elastic Modulus Of Amorphous Sio2 Nanowires, Hai Ni, Xiaodong Li, Hongsheng Gao
Elastic Modulus Of Amorphous Sio2 Nanowires, Hai Ni, Xiaodong Li, Hongsheng Gao
Faculty Publications
Amorphous SiO2 nanowires with diameter ranging from 50 to 100 nm were synthesized using chemical vapor deposition(CVD) under an argon atmosphere at atmospheric pressure. Nanoscale three-point bending tests were performed directly on individual amorphous SiO2 nanowires using an atomic force microscope (AFM).Elastic modulus of the amorphous SiO2 nanowires was measured to be 76.6±7.2GPa, which is close to the reported value of the bulk SiO2 and thermally grown SiO2 thin films, but lower than that of plasma-enhanced CVD SiO2 thin films. The amorphous SiO2 nanowires exhibit brittle fracture failure in bending.
Top-Down Structure And Device Fabrication Using In Situ Nanomachining, Xiaodong Li, Xinnan Wang, Qihua Xiong, Peter C. Eklund
Top-Down Structure And Device Fabrication Using In Situ Nanomachining, Xiaodong Li, Xinnan Wang, Qihua Xiong, Peter C. Eklund
Faculty Publications
We demonstrate the potential of an alternative tool for the fabrication of nanoscale structures and devices. A nanoindenter integrated with an atomic force microscope is shown to be a powerful machine tool for cutting precise length nanowires or nanobelts and for manipulating the shortened wires. We also demonstrate its utility in cutting grooves and fabricating dents (or periodic arrays of dents) in ZnSnanobelts. This approach permits the direct mechanical machining of nanodevices that are supported on a substrate without the inherent complications of e beam or photolithography.