Applied Mechanics Commons^™

Molecular Dynamics Modeling Of Polymers For Aerospace Composites, Swapnil Sambhaji Bamane

Dissertations, Master's Theses and Master's Reports

Polymer matrix composite materials are widely used as structural materials in aerospace and aeronautical vehicles. Resin/reinforcement wetting and the effect of polymerization on the thermo-mechanical properties of the resin are key parameters in the manufacturing of aerospace composite materials. Determining the contact angle between combinations of liquid resin and reinforcement surfaces is a common method for quantifying wettability. It is challenging to determine contact angle values experimentally of high-performance resins on CNT materials such as CNT, graphene, bundles or yarns, and BNNT surfaces. It is also experimentally difficult to determine the effect of polymerization reaction on material properties of a …

Wireless Power Transfer In Autonomous Mobile Microgrids, Carl Greene

Dissertations, Master's Theses and Master's Reports

The ability to autonomously dock unmanned ground vehicles plays a key role in mobile micro-grids, where efficient power transfer is paramount. The approach utilized in this work allows for near-field wireless power transfer in remote locations with minimal support. Establishing a micro-grid power system connection autonomously using wireless power eliminates the arduous task of designing a complex, multiple degrees of freedom (MDOF) robotic arm. The work presented in this thesis focuses on both the hardware and software within the micro-grid system. This particular near-field wireless system consists of a primary and secondary set of modules, comprised of Litz wire coils, …

A Coupled Viscoplastic-Damage Constitutive Model For Semicrystalline Polymers, Jeffrey Wiersma

Dissertations, Master's Theses and Master's Reports

The ease of processing, recyclability, and ideal cost to weight ratio makes the semi-crystalline polymers attractive in the aerospace, automotive, and defense industries. Use of semicrystalline polymers for engineering design requires a thorough understanding of their response to mechanical deformation, rate of loading, temperature, and failure mechanisms. However, there lacks a generally agreed upon constitutive model to capture the large deformation elastic-viscoplastic response of semicrystalline polymers while incorporating the strain-rate dependence and damage behavior. To address this aspect, the objective of this dissertation is to develop an elastic-viscoplastic constitutive model to predict the rate dependent, large deformation response of semicrystalline …

Atomistic-Continuum Membrane And Machine Learning Models For Two-Dimensional Materials, Upenda Yadav

Dissertations, Master's Theses and Master's Reports

“What could we do with layered structures with just the right layers?” asked Richard Feynman in his famous 1959 lecture, “There’s plenty of room at the bottom.” With the help of the amazing developments of the past several years, we are coming close to answering that question. In 2004, graphene was first isolated from graphite and only six short years later it won the Nobel Prize in Physics. Graphene is one atomic layer of Carbon, it is the thinnest and yet the strongest materials we have ever seen. It is 200 times stronger than its equivalent weight in steel and …

Concept Evaluation And Development Of A Novel Approach For Integration Of Turbogeneration, Electrification And Supercharging On Heavy Duty Engines, Satyum Joshi

Dissertations, Master's Theses and Master's Reports

While many technologies such as electrically assisted turbocharging, exhaust energy recovery and mild hybridization have already proven to significantly increase heavy-duty engine efficiency, the key challenge to their widespread adoption has been their cost effectiveness and packaging. This research specifically addresses these challenges through evaluation and development of a novel technology concept termed as the Integrated Turbogeneration, Electrification and Supercharging (ITES) system. The concept integrates a secondary compressor, a turbocompound/expander turbine and an electric motor through a planetary gearset into the engine cranktrain. The approach enables a reduced system cost and space-claim, while maximizing the efficiency benefits of independent technologies. …

Oxidative Aging And Fracture Behavior Of Polymers And Composites: Theory, Modeling And Experiments, Shabnam Konica

Dissertations, Master's Theses and Master's Reports

Polymers and their composites (PMC) have emerged as effective alternative materials in structural, aerospace, and automotive industries due to their lightweight and tunable properties compared to metals. However, these materials tend to degrade during their operations in extreme environments. In this work, two extreme conditions are considered: - i) high-temperature oxidative degradation of polymers and polymer-based composites ii) Fracture and damage of polymer-based composites under thermo-mechanical loading.

Polymer oxidation starts when oxygen from the ambient diffuses into the bulk material and initiates chemical reactions to develop a coarse, brittle oxide layer on the exposed surface. The oxidative degradation process is …

An Experimental Study Towards Underwater Propulsion System Using Structure Borne Traveling Waves, Shreyas Suhas Gadekar

Dissertations, Master's Theses and Master's Reports

The method of generating steady-state structure-borne traveling waves underwater in an infinite media creates abundant opportunities in the field of propulsive applications, and they are gaining attention from several researchers. This experimental study provides a framework for harnessing traveling waves in a 1D beam immersed under quiescent water using two force input methods and providing a motion to an object floating on the surface of the water.

In this study, underwater traveling waves are tailored using structural vibrations at five different frequencies in the range of 10Hz to 300Hz. The resulting fluid motion provides a propulsive thrust that moves a …

Marangoni Propulsion Of Active Particles, Saeed Jafari Kang

Dissertations, Master's Theses and Master's Reports

We study the surfing motion of active particles located at a flat liquid-gas interface. The particles create and maintain a surface tension gradient by asymmetrically discharging a surface tension-reducing agent. We employ theory and numerical simulation to investigate the Marangoni propulsion of these active surfers. First, we use the reciprocal theorem to establish a relationship between the propulsion speed and the release of the active chemical. This theoretical relation is utilized to examine the effect of wall confinement and geometry on the Marangoni-driven motion of active particle when the inertial effects are negligible and when the transports of the released …

Thermomechanical Mechanisms That Cause Adhesion Of Aluminum High Pressure Die Castings To The Die, Alex Monroe

Dissertations, Master's Theses and Master's Reports

In high pressure die casting (HPDC) of aluminum, cast material adhering to die is a significant defect. Adhesion occurs in two primary ways. The casting may stick preventing its removal from the die. Aluminum can also adhere to the die and buildup in local areas on the die surface with additional casting cycles. This second form of adhesion is called soldering. Lubricant is the best technology to control all forms of adhesion, but it comes at the cost of casting porosity, blisters, reduced die life, and increased die casting machine wear. New strategies to prevent adhesion are desired to eliminate …

Atomistic Continuum Simulations For Nano-Indentation And Compression Of Multi-Layer Graphene, Ashwini Nikumbh

Dissertations, Master's Theses and Master's Reports

Graphene has attracted a great share of research interest due to its extraordinary electrical, thermal, mechanical, and physical properties. Such spectacular properties of graphene open a wide range potential of applications in electronics, energy storage, composites, and biomedical fields. The mechanical properties of graphene can have a huge impact on its performance in graphene-based devices and thus it is important to study them. But the difficulties in experimental characterization and computational limitations to simulate large graphene sample consisting of billions of atoms makes it a challenging task. Thus, accurate and efficient simulation tools to predict the complex deformation of large …

Phase-Field Fracture Modeling For Interlocking Micro-Architectured Materials, Shubham Sinha

Dissertations, Master's Theses and Master's Reports

It is fascinating to see how natural materials like teeth enamel, bone and nacre possess a very high stiffness and strength in spite of the fact that they are composed of minerals mostly. Studies have shown the reason for this aberration as the presence of weaker interfaces with intricate interlocking architectures at microscopic levels in these materials. Inspired by the architecture of these materials, micro-architectured sutures with jig-saw like geometry is being studied in this research study. The main focus of this study is to examine the effects of friction co-efficient and interlocking angles of the jig-saw tabs on pullout …

Studying The Effects Of Initial Crack Angle On The Crack Propagation In Graphene Nano-Ribbon Through Molecular Dynamics Simulations, Vijay Kumar Pathak

Dissertations, Master's Theses and Master's Reports

In this research, we have worked on the brittle fracture of graphene nano-ribbon to explore the behavior of crack propagation at different crack angles. We have performed classical Molecular Dynamics simulations using LAMMPS at ten different crack angles between 0 degrees and 45 degrees, in an increment of 5 degrees to observe the parameters that dominate the crack path. The graphene nanoribbon is loaded in the zigzag direction by pulling it in the armchair direction with a pre-existing crack in the center. We have used OVITO for the visualization of the simulation. AIREBO potential is employed in this work because …

Investigation Of A Machine-Plant Interface For Extracting Rooted Invasive Aquatic Plants, Brad Baas

Dissertations, Master's Theses and Master's Reports

The current solutions for managing rooted aquatic invasive plants are time consuming, have negative environmental impacts, or are cost-limiting for management organizations. The most effective treatment method is hand pulling, but hand pulling is not a feasible solution for a whole lake. A new device, the invasive aquatic plant extractor, aims to replace human divers who hand pull plants with a mechanical system. The device implements a machine-plant interface that resembles the tines of a fork. These tines will be pushed linearly through the substrate, and then raised from the substrate with the plant caught in the tines. The primary …

Multiscale Modeling Of Carbon Fibers/Graphene Nanoplatelets/Epoxy Hybrid Composites For Aerospace Applications, Hashim Al Mahmud

Dissertations, Master's Theses and Master's Reports

Significant research effort has been dedicated for decades to improve the mechanical properties of aerospace polymer-based composite materials. Lightweight epoxy-based composite materials have increasingly replaced the comparatively heavy and expensive metal alloys used in aeronautical and aerospace structural components. In particular, carbon fibers (CF)/graphene nanoplatelets (GNP)/epoxy hybrid composites can be used for this purpose owing to their high specific stiffness and strength. Therefore, this work has been completed to design, predict, and optimize the effective mechanical properties of CF/GNP/epoxy composite materials at different length scales using a multiscale modeling approach. The work-flow of modeling involves a first step of using …

Increasing Access To Pv Technology Through Sustainable Racking: A Review Of Existing Literature And Ground Mounted Fixed Tilt Designs, And What Can Be Done Next, Parijata Prabhakara

Dissertations, Master's Theses and Master's Reports

There is a lack of literature on the structural balance of systems (BOS), also called racking, for ground mount, fixed-tilt solar PV systems. Literature that exists discusses mostly rooftop racking and installations, additional wind loading, and weight considerations imposed on roofs, and little guidance is provided in building codes. The lack of peer-reviewed guidance on design requirements for domestic and large-scale application solar PV racking systems leaves most consumers relying on expensive, patented, off-the-shelf hardware. As PV cell technology and module costs have improved, we can start to focus on PV BOS improvements (particularly racking) and move towards sustainable designs …

Optimization And Comparison Of Over-Expanded And Other High Efficiency Four-Stroke Spark-Ignited Boosted Engines, Zhuyong Yang

Dissertations, Master's Theses and Master's Reports

Recent fuel economy and emission regulations are the major concern of the research and development of modern internal combustion engine. Such technologies include variable valve timing (VVT), direct injection (DI), turbocharging, downsizing, and over-expanded cycle are used by many manufacturers to improve engine fuel economy or increase power density.

Current Atkinson cycle technology in the production engine is mainly realized by an advanced valvetrain system to reduce the effective compression ratio while maintaining the same expansion ratio. Another approach to realize over-expanded cycle engine is to utilize a multi-link cranktrain mechanism. Although the Atkinson cycle was originally patented in the …

Modeling And Analysis For Driveline Jerk Control, Prince Lakhani

Dissertations, Master's Theses and Master's Reports

In modern-day automotive industry, automotive manufacturers pay keen attention to driver’s safety and comfort by ensuring good vehicle drivability, feel of acceleration, limiting jerk and noise. The vehicle driveline plays a critical role to meet these criteria. By using high-fidelity simulation tool such as AMESim®, it is now possible to accurately model the vehicle driveline to be tested for different scenarios. With Simulink®, one can develop an efficient torque-based control system to limit the driveline oscillations and the generated noise. So, a joint simulation is used which provides a platform to evaluate the estimators and control system while considering the …

Computational Studies On Biomechanics Of Concussion And On Efficacy Of Football Helmets, David Labyak

Dissertations, Master's Theses and Master's Reports

Football helmets have been used for many years to prevent head injuries to players. Over the years, the helmet design has evolved from a crude leather head covering to the more recent form fitting helmets that are seen today. The one design feature that has been common in the majority of all helmets is a hard polycarbonate shell with a foam cushion padding. The main goal of the padding layer was to reduce the amount of linear acceleration during an impact event. The one feature that has been overlooked is how stiff the padding is in rotation.

The purpose of …

Turbulent Transition Simulation And Particulate Capture Modeling With An Incompressible Lattice Boltzmann Method, John R. Murdock

Dissertations, Master's Theses and Master's Reports

Derivation of an unambiguous incompressible form of the lattice Boltzmann equation is pursued in this dissertation. Further, parallelized implementation in developing application areas is researched. In order to achieve a unique incompressible form which clarifies the algorithm implementation, appropriate ansatzes are utilized. Through the Chapman-Enskog expansion, the exact incompressible Navier-Stokes equations are recovered. In initial studies, fundamental 2D and 3D canonical simulations are used to evaluate the validity and application, and test the required boundary condition modifications. Several unique advantages over the standard equation and alternative forms found in literature are found, including faster convergence, greater stability, and higher fidelity …

Fea Analysis And Optimization Of Differential Housing For Fatigue Stresses And Fatigue Test Design To Study Skin Effect In Ductile Iron, Swapnil A. Pandey

Dissertations, Master's Theses and Master's Reports

Automotive emission standards are getting more stringent day by day and governments worldwide are moving to reduce emissions from automobiles. In this scenario reducing the weight of automobile components becomes an important design objective to reduce emissions. A 10% reduction of weight in the complete automobile leads to 6-8 percent improvement in mileage (Mhapankar 2015). Also, powertrain components make up for approximately 27% of the total automobile weight and thus optimizing the design of components in the powertrain is an important task (Mhapankar 2015). Statistics show that 26% of component failures in automobiles are part of powertrain and 21% of …

Frontal Crash Analysis Of A Conformable Cng Tank Using Finite Element Analysis, Datta Sandesh Manjunath

Dissertations, Master's Theses and Master's Reports

The purpose of this study is to computationally model and analyze a Conformable Compressed Natural Gas (CNG) fuel tank for frontal crashes using Finite Element Analysis. Researchers have developed a CNG fuel tank, which is conformable, non-conventional and non-cylindrical. This tank increases cost efficiency, volumetric efficiency and cargo efficiency in CNG vehicle applications. A lightweight pickup truck (2015 Chevrolet Silverado) has been used to integrate the CNG tanks and field-testing has been conducted to demonstrate the application.

The report mainly focuses on the effective finite element modeling of the chassis, brackets and tanks using HYPERMESH and RADIOSS. The frontal crash …

Restraint System Design And Evaluation For Military Specific Applications, Sebastian Karwaczynski

Dissertations, Master's Theses and Master's Reports

This research focuses on designing an optimal restraint system for usage in a military vehicle applications. The designed restraint system must accommodate a wide range of DHM’s and ATD’s with and without PPE such as: helmet, boots, and body armor. The evaluation of the restraint systems were conducted in a simulated vehicle environment, which was utilized to downselect the ideal restraint system for this program.

In December of 2011 the OCP TECD program was formulated to increase occupant protection. To do this, 3D computer models were created to accommodate the entire Soldier population in the Army. These models included the …

Design And Fabrication Of A Suspension Rig, Abhijith Geo Philip

Dissertations, Master's Theses and Master's Reports

Owing to its placement under the vehicle body, the suspension system is one of the parts of the vehicle which are difficult to comprehend completely, albeit being a vital component. For demonstrating the working of a suspension system, a physical model in which one can actually see the movement of all the components would be a great tool. A Mustang II independent front suspension system was purchased from Heidts Engineering Performance and a rig that can emulate some of the real world situations of vehicle suspension action was designed and fabricated. All the components are accessible and conditions like bounce, …

An Assessment Of Flow Regime Maps And A Numerical Heat Transfer Correlation For The Stratified/Annular Regime Of Shear-Driven Internal Condensing Flows, Fnu Nikhil Shankar

Dissertations, Master's Theses and Master's Reports - Open

Several modern-day cooling applications require the incorporation of mini/micro-channel shear-driven flow condensers. There are several design challenges that need to be overcome in order to meet those requirements.

The difficulty in developing effective design tools for shear-driven flow condensers is exacerbated due to the lack of a bridge between the physics-based modelling of condensing flows and the current, popular approach based on semi-empirical heat transfer correlations. One of the primary contributors of this disconnect is a lack of understanding caused by the fact that typical heat transfer correlations eliminate the dependence of the heat transfer coefficient on the method of …