Applied Mechanics Commons^™

Introduction To Vacuum Technology, David M. Hata, Elena V. Brewer, Nancy J. Louwagie

Milne Open Textbooks

Vacuum systems are critical to many industries. They are vital to establishing required process pressures, establishing a clean process environment, and removing reaction by-products from the process chamber. This text, a revision and expansion of David Hata’s Introduction to Vacuum Technology published in 2008, addresses basic topics in vacuum technology for individuals tasked with maintaining vacuum systems and instructors teaching technician-level courses. The topics are carefully curated to the needs of technicians in a production environment and the types of vacuum systems used, and the accompanying laboratory manual and instructor’s guide support the delivery of lecture-laboratory courses.

This book approaches …

Investigation Of Fatigue Response With Analytical And Machine Learning Models And Hygroscopic Analysis Of Asymmetric Bistable Cfrp Composites, Shoab Ahmed Chowdhury

All Dissertations

Asymmetric bistable carbon fibre reinforced plastic (CFRP) composites enable a broad range of applications as they can sustain multiple stable configurations and have small snap-through load requirements. These unique features, coupled with their light strength-to-weight and stiffness-to-weight ratios, have made them preferred options for multifunctional systems. This study investigates the fatigue and hygroscopic response of 2-ply, [0/90] bistable CFRP laminates and proposes predictive modeling approaches for improved performance.

While previous studies widely researched and documented the fatigue of general composites in axial loading, fatigue analysis of asymmetric bistable composites in the out-of-plane snap-through direction is inadequate. This study performs fatigue …

Valve Efficiency Testing Device, Jake Robert Rydberg, Andrew Keith Willardson, Jake Ben Jezier, Emily Marie Wannenmacher

Mechanical Engineering

This document serves as the official Final Design Review (FDR) for the mechanical engineering team on the Valve Efficiency Testing Device project for the Phillips 66 Rodeo Refinery. The team attends California Polytechnic State University, San Luis Obispo. The project involved designing and building a valve efficiency testing device. The goal was to create a finished test device that can be used in the Phillips 66 Rodeo Refinery machine shop to test reciprocating compressor valves before they are installed. The purpose of this document is to describe the manufacturing and design verification activities that have been completed since Critical Design …

Valve Efficiency Testing Device, Jake Robert Rydberg, Andrew Keith Willardson, Jake Ben Jezier, Emily Marie Wannenmacher

Mechanical Engineering

This document serves as the official Final Design Review (FDR) for the mechanical engineering team on the Valve Efficiency Testing Device project for the Phillips 66 Rodeo Refinery. The team attends California Polytechnic State University, San Luis Obispo. The project involved designing and building a valve efficiency testing device. The goal was to create a finished test device that can be used in the Phillips 66 Rodeo Refinery machine shop to test reciprocating compressor valves before they are installed. The purpose of this document is to describe the manufacturing and design verification activities that have been completed since Critical Design …

Disc Golf Throwing Robot, Nevada S. Schultz, Sydney M. Lewis, Erick Edmundo Daza, Rachel Alysse Greenberg, Peter M. Kean

Mechanical Engineering

Disc golf companies need better methods to test disc flight. The scope of this project is to create a disc throwing robot that can throw a disc golf driver 450-500 feet, with control over the speed, spin, and release angle. Research shows that multiple disc-throwing products exist; however, none meet the full requirements of this project. The Cal Poly senior project design team created a proof-of-concept machine. This prototype started as a two-wheel mechanism. Eventually, a third wheel was added, allowing for complete control over disc spin. The three-wheel prototype reached 62 mph when perfectly calibrated. The prototype is accurate, …

4wd Baja Upright And Wheel Hub, Nathan Thompson, Jonathan P. Larson, Spencer D. Compan

Williams Honors College, Honors Research Projects

The University of Akron Zips Baja Team has switched to a 4-wheel-drive (4WD) vehicle as per the 2023 Baja Society of Automotive Engineers (SAE) rules. The 2022 Baja Vehicle was 2WD, thus the upright and wheel hub were designed exclusively for a 2-wheel-drive (2WD) Baja vehicle. This report entails the design process and methods of verification for the design of the 4WD upright and wheel hub.

Mechanical Energy Harvester For Powering Rfid Systems Components: Modeling, Analysis, Optimization And Design, Alireza Babaei

Theses and Dissertations--Mechanical Engineering

Finding alternative power sources has been an important topic of study worldwide. It is vital to find substitutes for finite fossil fuels. Such substitutes may be termed renewable energy sources and infinite supplies. Such limitless sources are derived from ambient energy like wind energy, solar energy, sea waves energy; on the other hand, smart cities megaprojects have been receiving enormous amounts of funding to transition our lives into smart lives. Smart cities heavily rely on smart devices and electronics, which utilize small amounts of energy to run. Using batteries as the power source for such smart devices imposes environmental and …

Fluid Power Vehicle Challenge, Bryce Towne, Ethan Andrews, Carter Moore, Andrew Sobel

Williams Honors College, Honors Research Projects

The Fluid Power Vehicle Challenge is a competition held by the National Fluid Power Association (NFPA) that challenges students to create a hydraulically powered vehicle to compete in four different races over two days. The vehicle has to be fully powered by hydraulics, with human power (such as pedaling) being used to move the hydraulic fluid. Electronics and pneumatics can be used to control the flow of the hydraulic oil. Vehicles also must have an energy storage device to take advantage of regenerative braking. The final competition was at the Norgren facility in Colorado from April 12th to April 14th. …

Novel Hitch Cargo Cart, Cesilio Sanchez Ramirez, Lance Haidet, Richard Lontoc, Tyler Selinka

Mechanical Engineering

This document presents the engineering design process used to develop, manufacture, and test a new and improved iteration of a hitch cart prototype. This process was performed by a team of four mechanical engineering seniors as part of California Polytechnic State University, San Luis Obispo’s senior design pathway. The goal of this project was to develop a sturdy and reliable iteration of our sponsor’s hitch cart prototype, that integrated the functionality of a vehicle hitch cargo platform and that of a height adjustable cargo cart into a single streamlined and easy to use product. This design could be used by …

Novelty Ice Cream Assembly Prototype, Mason Sylvester, Logan Williamson, Alvaro Martinez, Adin Gilman-Cohen

Mechanical Engineering

Cool Beans USA is a novelty ice cream startup company founded by Keith Zachow. In the winter of 2022, our team began working with Mr. Zachow to develop a machine to automate parts of the production process for his product. This product consists of two hemispherical ice-cream cone shell halves filled with soft serve ice cream and pressed together. The assembled pods are around the size and shape of a small walnut and are intended to be sold in stores as a frozen finger food. At the time of project inception, this product was in its early stages and was …

Modeling, Control And Estimation Of Reconfigurable Cable Driven Parallel Robots, Adhiti Raman Thothathri

All Dissertations

The motivation for this thesis was to develop a cable-driven parallel robot (CDPR) as part of a two-part robotic device for concrete 3D printing. This research addresses specific research questions in this domain, chiefly, to present advantages offered by the addition of kinematic redundancies to CDPRs. Due to the natural actuation redundancy present in a fully constrained CDPR, the addition of internal mobility offers complex challenges in modeling and control that are not often encountered in literature.

This work presents a systematic analysis of modeling such kinematic redundancies through the application of reciprocal screw theory (RST) and Lie algebra while …

Tunable Filtration Of Particles During Dip-Coating, Connor Copeland

All Theses

When a solid substrate is withdrawn from a liquid bath a thin coating is deposited whose thickness is given by the Landau-Levich-Derjaguin (LLD) law. We perform an experimental study of dip coating of particle suspensions showing that particles of a given size can become entrained in the meniscus by the competition between viscous and surface tension forces. This is called capillary filtration and can be used as a tunable dynamic filter. For single particle suspensions, filtration can be in terms of either clumps or single particles, with the relevant entrainment points depending upon the rheology of the working fluid, either …

Creep Behavior Of A Ti-Based Multi-Principal Element Alloy, Benjamin Elbrecht

All Theses

Abstract

The understanding of microstructural damage mechanisms is the foundation of better understanding existing materials and future material development. There are significant challenges to measuring these damage mechanisms in-situ as continuous observation of the state of the microstructure is difficult or impossible for many experimental setups. This thesis presents a method for measuring grain boundary sliding (GBS) and local strain concentrations in-situ via a Heaviside function based algorithm. GBS is the shearing of two grains along their shared grain boundary and is a common damage mechanism in creep which presents as a discontinuity that can be measured with a Heaviside …

Interactive Lego Girl Scout Arm, Chris Suzuki, Emi Okuyama, Bryson Shores, Karina Sandoval

Mechanical Engineering

This Senior Project Report document outlines the senior design project for Girl Scouts of California’s Central Coast (GSCCC) led by a team of four Mechanical Engineering students at California Polytechnic State University, San Luis Obispo. The project encompasses the researching, designing, prototyping, and testing of a LEGO robotic arm for the Girl Scouts to learn more about STEM (Science, Technology, Engineering, and Mathematics) and provide support to each Girl Scouts cookie sales in their stores. Their goal was to build a LEGO robotic arm that will interact with customers at the Girl Scout stores and promote the girl scouts' interest …

Examining The Different Snap-Through Characteristics Of Bistable Cfrp Composite Laminates, Vishrut Deshpande

All Theses

Bistable carbon fiber composites, whose bistability arises from having asymmetric fiber layouts in different layers, have shown immense potential for use in shape morphing and adaptive structure applications. While many studies in this field focus on these composite laminates’ external shapes at the two stable states, their snap-through behavior of shifting from one stable shape to the other remains a critical aspect to be investigated in complete detail. Moreover, symmetric loading conditions have been extensively studied based on the classical lamination theory, but the asymmetric loading conditions received far less attention. Therefore, this study examines an asymmetric, localized point load …

Eastman Guide Rail Project, Camryn J. Hurley, Jace Lyon, Isaiah Wallace, Cole Thomas, Erin Bennett

Chancellor’s Honors Program Projects

No abstract provided.

Wireless Power Transfer In Autonomous Mobile Microgrids, Carl Greene

Dissertations, Master's Theses and Master's Reports

The ability to autonomously dock unmanned ground vehicles plays a key role in mobile micro-grids, where efficient power transfer is paramount. The approach utilized in this work allows for near-field wireless power transfer in remote locations with minimal support. Establishing a micro-grid power system connection autonomously using wireless power eliminates the arduous task of designing a complex, multiple degrees of freedom (MDOF) robotic arm. The work presented in this thesis focuses on both the hardware and software within the micro-grid system. This particular near-field wireless system consists of a primary and secondary set of modules, comprised of Litz wire coils, …

R/C Baja Truck Suspension, Chassis And Steering, Ryan Lafrombois

All Undergraduate Projects

The ASME RC Baja Challenge is an annual competition that the Central Washington University Mechanical Engineering and Technology (MET) department takes part in. Senior level engineers divided the work between the drivetrain and the chassis/suspension while designing and manufacturing to meet a set of requirements. Next, a device was to be developed to be able to withstand the extreme forces to be successful in the competition at the end of the year. The process would require that the students use their acquired knowledge and skills to design, manufacture, and analyze a capable device. Designing involved the completion of 12 analyses …

Concept Evaluation And Development Of A Novel Approach For Integration Of Turbogeneration, Electrification And Supercharging On Heavy Duty Engines, Satyum Joshi

Dissertations, Master's Theses and Master's Reports

While many technologies such as electrically assisted turbocharging, exhaust energy recovery and mild hybridization have already proven to significantly increase heavy-duty engine efficiency, the key challenge to their widespread adoption has been their cost effectiveness and packaging. This research specifically addresses these challenges through evaluation and development of a novel technology concept termed as the Integrated Turbogeneration, Electrification and Supercharging (ITES) system. The concept integrates a secondary compressor, a turbocompound/expander turbine and an electric motor through a planetary gearset into the engine cranktrain. The approach enables a reduced system cost and space-claim, while maximizing the efficiency benefits of independent technologies. …

An Experimental Study Towards Underwater Propulsion System Using Structure Borne Traveling Waves, Shreyas Suhas Gadekar

Dissertations, Master's Theses and Master's Reports

The method of generating steady-state structure-borne traveling waves underwater in an infinite media creates abundant opportunities in the field of propulsive applications, and they are gaining attention from several researchers. This experimental study provides a framework for harnessing traveling waves in a 1D beam immersed under quiescent water using two force input methods and providing a motion to an object floating on the surface of the water.

In this study, underwater traveling waves are tailored using structural vibrations at five different frequencies in the range of 10Hz to 300Hz. The resulting fluid motion provides a propulsive thrust that moves a …

Ternary Flow Simulation Based On The Conservative Phase Field Lattice Boltzmann Method, Chunheng Zhao

Dissertations and Theses

In this thesis, we numerically investigated multi-phase fluid dynamics (2 and 3-phase flow) by solving the Navier-Stokes equations coupled with the conservative phase field (CPF) equations using the Lattice Boltzmann method (LBM). To effectively simulate the large-scale multi-phase physics, we developed an open-source software, IMEXLBM, which can be easily parallelized on both CPUs and GPUs without significant modifications to the code. We first validated various parts of this software and then used this method to study the interaction of rising bubbles with a static oil droplet as well as the engulfment of the water droplet on solids coated with a …

Investigations Of The Low Temperature Combustion Regions And Emissions Characteristics Of Aerospace F24 In A Constant Volume Combustion Chamber And A Common Rail Direct Injection Ci Engine, Richard C. Smith Iii

Electronic Theses and Dissertations

A study was conducted to investigate the low temperature combustion (LTC) regions of aerospace F24 and ULSD in the static setting of a CVCC and the dynamic setting of a CRDI research engine. This research is conducted to reduce in-cylinder emissions by understanding and implementing a technique to achieve an extended LTC. Emissions data for this study were collected during the operation of the CRDI research engine with a MKS 2030 FTIR and an AVL Microsoot 483. The parameters researched within the static setting of the CVCC included the determinations of the cool flames and NTC regions within the LTHR …

Determining Cause Of Failure For Load Cells Supporting Vertical Pressure Vessels Subject To Wind Loading, Seth Nowak

Electronic Theses and Dissertations

Wind loads cannot be avoided during a natural disaster such as a hurricane and could affect the strength and stability of vertical pressure vessels during exposure. Vertical pressure vessels cater to large wind loads; therefore, it is imperative to study the effect of additional loading on the structures. In this study, three pressure vessels with volumes of 50 CuFt, 200 CuFt, and 1100 CuFt, supported by three equidistant load cells under their legs are individually analyzed to determine von mises stress to estimate yield failure criteria. Two load rating criteria, maximum load capacity and water-filled condition (critical condition) are utilized …

Adjustable Head Tube Angle Headset, Glenn Petersen, Ben Harper, Josh Martin, Dylan Prins

Mechanical Engineering

This final design review report describes the design, manufacture, and test process of a bicycle headset capable of quickly and easily adjusting the effective head tube angle. The evolution of mountain bike geometry has forced bike designers to compromise between climbing and descending performance when choosing a head tube angle. A headset capable of quickly adjusting the effective head tube angle would allow riders to optimize their bike’s geometry for different stages of riding. This report details the research, idea generation, concept development and selection, design, manufacturing, and testing of our adjustable head tube angle headset.

Adaptive Vehicle Control, Brian L. Finger, Maria Vargas, Jacob T. Larson, Christopher J. Villa

Mechanical Engineering

This report presents the final design for our device made for Mrs. Laura Jagels. Mrs. Jagels, who has an above the knee amputation, needed a device that would allow her to operate a manual car in a safe and reliable way that still gives her the traditional driving experience. This report takes into consideration the shortcomings of current market devices that enable amputees to operate vehicles. From this research and through interviews with Mrs. Jagels, we were able to decide on our device specifications, giving us a basis to objectively evaluate designs. Ideation and concept prototype building was performed for …

F34 Beekeeper Assist, Kyle Ladtkow, Javier Guerra, Jose Velazquez, Ryan Heryford

Mechanical Engineering

Alejandro Jauregui is a veteran who now works as a commercial beekeeper. He lost both of his legs during his service. While his current prostheses allow him to fully complete his work, he has found that inspection of the bee boxes causes him severe hip and back pain. Bee box inspection is a critical task for beekeeping, especially since he maintains about 200 hives every day. Our senior project team was tasked with designing and building a device that would help him move the top bee box out of the way to allow for inspection. We performed preliminary research into …

Kennesaw State University And United Alloy Corporation Robotic Pick And Place Project, Kathryn Bharadwaj, Logan Spencer, Tharkun Hudlow

Senior Design Project For Engineers

United Alloy Corporation (UAC), a company specializing in unique aluminum parts for aeronautics, needed a fix to their error prone, labor-intensive billet press operation. The process has a problem of adding the wrong size or wrong alloy billet to the induction oven, which results in a waste of raw materials. The billets range from ten to thirty-seven inches in length and weigh up to three hundred pounds. Currently, an operator uses a gantry crane to check and lift the billets from a rack onto the magazine of an induction oven. The magazine can hold up to three billets safely and …

A Single-Stage Passive Vibration Isolation System For Scanning Tunneling Microscopy, Toan T. Le

Master's Theses

Scanning Tunneling Microscopy (STM) uses quantum tunneling effect to study the surfaces of materials on an atomic scale. Since the probe of the microscope is on the order of nanometers away from the surface, the device is prone to noises due to vibrations from the surroundings. To minimize the random noises and floor vibrations, passive vibration isolation is a commonly used technique due to its low cost and simpler design compared to active vibration isolation, especially when the entire vibration isolation system (VIS) stays inside an Ultra High Vacuum (UHV) environment. This research aims to analyze and build a single-stage …

Jcati Carbon Fiber Recycling Shredder, Benjamin Cooley

All Undergraduate Projects

Once carbon fibers are cast into a resin and used in a composite material, retrieving those fibers can be a difficult task. However, it is beneficial to recycle and reuse the fibers from old unneeded components rather than pay the cost of acquiring new ones. The Joint Center for Aerospace Technology Innovation (JCATI) carbon fiber recycling device condenses the multistep process of extracting the fibers by integrating all steps into one automated device. In the previous version of the device, the cutting blades turned the long composite strips into thin fingers but did not sever them across the width.

The …

Hydraulic Vehicle Challenge, Jacob Steiner, David Kotovets, Evan Blitz, Luke Fetherston, Alex Colucy

Williams Honors College, Honors Research Projects

The target goal of this project is for a team of students to design a vehicle which is based on human power as the primary mover of the system and achieves vehicle propulsion through the required use of hydraulics and pneumatics. In summary, the rider will power a pump that will generate pressure in order to move the fluid that drives the motor. This will result in the powered rotation of the wheels. As there are many possible designs, naturally, this means that the final design for the vehicle will have specific limitations such as weight and the required use …