Open Access. Powered by Scholars. Published by Universities.®
- Keyword
-
- 3D printed optics (1)
- Additive Manufacturing (1)
- Automation (1)
- Cahn-Hilliard Equation (1)
- Composite materials (1)
-
- Computational models (1)
- Control Systems (1)
- Customization (1)
- Density functional theory (1)
- Engineering Design (1)
- Excavation (1)
- Flory-Huggins (1)
- Mechanical properties (1)
- Membrane formation (1)
- Membrane morphology (1)
- Membrane performance (1)
- Micro 3D printing (1)
- Microeheaters (1)
- Microextrusion (1)
- Molecular dynamics (1)
- Molybednum disilicide (1)
- Multiscale computational modeling (1)
- Nanomaterials (1)
- Phase inversion (1)
- Phase separation (1)
- Robotics (1)
- Waveguides (1)
Articles 1 - 6 of 6
Full-Text Articles in Applied Mechanics
Phase-Field Modeling Of The Polymer Membrane Formation Process For Micro- And Ultra-Filtration, Michael Rosario Cervellere
Phase-Field Modeling Of The Polymer Membrane Formation Process For Micro- And Ultra-Filtration, Michael Rosario Cervellere
Graduate Theses and Dissertations
Porous polymer membrane filters are widely used in separation and filtration process. Micro- and ultra-filtration membranes are commonly used in biopharmaceutical applications such as filtering viruses and separating proteins from a carrier solution. The formation of these membrane filters via phase inversion is a complex and interconnected process where varying casting conditions can have a wide variety of effects on the final membrane morphol- ogy. Tailoring membrane filters for specific performance characteristics is a tedious and time consuming process. The time and length scales of membrane formation make it extremely difficult to experimentally observe membrane formation. Modeling the membrane formation …
Microextrusion 3d Printing Of Optical Waveguides And Microheaters, Edidiong Nseowo Udofia
Microextrusion 3d Printing Of Optical Waveguides And Microheaters, Edidiong Nseowo Udofia
Graduate Theses and Dissertations
The drive for smaller and more compact devices presents several challenges in materials and fabrication strategies. Although photolithography is a well-developed method for creating microdevices, the disparate requirements in fabrication strategies, material choices, equipment and process complexities have limited its applications. Microextrusion printing (μEP) provides a promising alternative for microfabrication. Compared to the traditional techniques, the attractions lie in the wide range of printable material choice, greater design freedom, fewer processing steps, lower cost for customized production, and the plurality of compatible substrates. However, while extrusion-based 3D printing processes have been successfully applied at the macroscale, this seeming simplicity belies …
Predicting The Mechanical Properties Of Nanocomposites Reinforced With 1-D, 2-D And 3-D Nanomaterials, Scott Edward Muller
Predicting The Mechanical Properties Of Nanocomposites Reinforced With 1-D, 2-D And 3-D Nanomaterials, Scott Edward Muller
Graduate Theses and Dissertations
Materials with features at the nanoscale can provide unique mechanical properties and increased functionality when included as part of a nanocomposite. This dissertation utilizes computational methods at multiple scales, including molecular dynamics (MD) and density functional theory (DFT), and the coupled atomistic and discrete dislocation multiscale method (CADD), to predict the mechanical properties of nanocomposites possessing nanomaterials that are either 1-D (carbyne chains), 2-D (graphene sheets), or 3-D (Al/amorphous-Si core-shell nanorod).
The MD method is used to model Ni-graphene nanocomposites. The strength of a Ni-graphene nanocomposite is found to improve by increasing the gap between the graphene sheet and a …
Motor Control Systems Analysis, Design, And Optimization Strategies For A Lightweight Excavation Robot, Austin Jerold Crawford
Motor Control Systems Analysis, Design, And Optimization Strategies For A Lightweight Excavation Robot, Austin Jerold Crawford
Graduate Theses and Dissertations
This thesis entails motor control system analysis, design, and optimization for the University of Arkansas NASA Robotic Mining Competition robot. The open-loop system is to be modeled and simulated in order to achieve a desired rapid, yet smooth response to a change in input. The initial goal of this work is to find a repeatable, generalized step-by-step process that can be used to tune the gains of a PID controller for multiple different operating points. Then, sensors are to be modeled onto the robot within a feedback loop to develop an error signal and to make the control system self-corrective …
The Effect Of Incorporating End-User Customization Into Additive Manufacturing Designs, Jonathan D. Ashley
The Effect Of Incorporating End-User Customization Into Additive Manufacturing Designs, Jonathan D. Ashley
Graduate Theses and Dissertations
In the realm of additive manufacturing there is an increasing trend among makers to create designs that allow for end-users to alter them prior to printing an artifact. Online design repositories have tools that facilitate the creation of such artifacts. There are currently no rules for how to create a good customizable design or a way to measure the degree of customization within a design. This work defines three types of customizations found in additive manufacturing and presents three metrics to measure the degree of customization within designs based on the three types of customization. The goal of this work …
Particle Image Velocimetry Design & Installation, Zach Ritchie
Particle Image Velocimetry Design & Installation, Zach Ritchie
Mechanical Engineering Undergraduate Honors Theses
This work will mainly focus on the design, construction, and installation of the Particle Image Velocimetry (PIV) system in the Chemical Hazards Research Center wind tunnel. The PIV system utilizes a Class IV (double pulsed) laser, optics to produce a light sheet, timing circuitry, and a high-resolution camera (with buffered output) to measure a system’s velocity (two-dimensional) field by determining the displacement of particles over the time between laser pulses. For maximum mobility and functionality, the PIV system was installed in the center of the tunnel on a moveable cart with the laser and camera mounted to an adjustable support. …