Acoustics, Dynamics, and Controls Commons^™

Efficacy Of Passive Ventilation With High Exhaust Demands: A Case Study Of Cal Poly Sst, Siddarth Bokka

Construction Management

The Simpson Strong Tie Demonstration Laboratory serves as a multipurpose space allowing students at the College of Architecture and Environmental Design at California Polytechnic State University to build full scale construction projects. The building features a material storage area, a high bay for construction of full-scale projects, and a mezzanine level that houses digital fabrication equipment. However, the building was never designed to house the specific equipment currently installed on the mezzanine and ventilate the exhaust fumes from them. Rather, the building relies on passive natural ventilation that is likely ineffective at properly exhausting hazardous fumes, resulting in complaints from …

Enhancing Bridge Resilience And Overheight Vehicle Mitigation Through Innovative Sacrificial Cushion Systems, Aly Mousaad Aly, Marc Hoffmann

Faculty Publications

Transportation departments have made significant strides in addressing the challenges posed by the increasing weights of trucks on bridges. While there is a growing awareness of overheight vehicle collisions with bridges, implementing effective countermeasures remains limited. The susceptibility of bridges to damage from such collisions is on the rise, further exacerbated by unpredictable lateral impact forces. This study employs nonlinear impact analysis to assess the response of an unprotected vehicle-girder model, yielding realistic deformation outcomes comparable to observed impacts on the US-61 bridge. Predictions for a truck traveling at 112.65 km/h indicate deformations of 0.229 m, 0.161 m, and 0.271 …

Performance Comparison Of Several Control Algorithms For Tracking Control Of Pantograph Mechanism, Laylaa Mahmoud Eng, Mohamed Shamseldin Dr, Mohamed Sallam Dr, Abdelghany Mohamed Prof

Future Engineering Journal

A sort of parallel manipulator known as a pantograph robot mechanism was created primarily for industrial requests that required high precision and satisfied speed. While tracking a chosen trajectory profile requires a powerful controller. Because it has four active robot links and one robot passive link in place of just two links like the open chain does, it can carry more loads than the open chain robot mechanism while maintaining accuracy and stability. The calculated model for a closed chain pantograph robot mechanism presented in this paper takes into account the boundary conditions. For the purpose of simulating the dynamics …

Optimization Of A Lightweight Floating Offshore Wind Turbine With Water-Ballast Motion Mitigation Technology, William Ramsay

Electronic Theses and Dissertations

Floating offshore wind turbines are a promising technology to address energy needs utilizing wind resources offshore. The current state of the art is based on heavy, expensive platforms to survive the ocean environment. Typical design techniques do not involve optimization because of the computationally expensive time-domain solvers used to model motions and loads in the ocean environment. However, this project uses an efficient frequency domain solver with a genetic algorithm to rapidly optimize the design of a novel floating wind turbine concept. The concept utilizes liquid ballast mass to mitigate motions on a lightweight post-tensioned concrete platform, with a target …

A Practical Methodology To Detect, Quantify And Characterize Experimental Uncertainties In The Dynamic Testing Of Structures, James L. Woodall

Civil Engineering ETDs

This thesis investigates the uncertainty in the experimental context of structural dynamics. This thesis proposes a method to estimate both the effect of boundary conditions, as well as two different methods to detect the location of sensors on a specimen. Firstly, this thesis proposes a technique to predict the dynamic behavior of any point along a cantilever beam with an uncertain transverse elastic restraint. Secondly, this thesis investigates the estimation of the location of a sensor given the output data of a physical experiment with two different methods. Small errors in the sensor location may go unnoticed in the frequency …

Accelerated Controller Tuning For Wind Turbines Under Multiple Hazards, Aly Mousaad Aly, Milad Rezaee

Faculty Publications

During their lifecycle, wind turbines can be subjected to multiple hazard loads, such as high-intensity wind, earthquake, wave, and mechanical unbalance. Excessive vibrations, due to these loads, can have detrimental effects on energy production, structural lifecycle, and the initial cost of wind turbines. Vibration control by various means, such as passive, active, and semi-active control systems provide crucial solutions to these issues. We developed a novel control theory that enables semi-active controller tuning under the complex structural behavior and inherent system nonlinearity. The proposed theory enables the evaluation of semi-active controllers’ performance of multi-degrees-of-freedom systems, without the need for time-consuming …

Renewable Energy Production By Solar Chimney: The Influence Of Curved Guide Vanes On The Performance Of A Solar Chimney Using Cfd Simulation, Haokun Xue

Theses, Dissertations and Capstones

The aim of this study is to investigate the effect of the guide vanes on the efficiency of the turbine of solar chimney power plant using Computational Fluid Dynamics (CFD). In this study, a 3-Dimentional CFD simulation of solar chimney power plant based on the Manzanares prototype is performed. The CFD simulation is validated by comparing the experimental data from the Manzanares prototype and simulation data with both 2D and 3D cases. To capture turbulent flow inside the chimney, the SST 𝑘 − 𝜔 turbulence model is used. The first object is to investigate the flow performance under the influence …

Localization Of Stationary Source Of Floor Vibration Using The Steered Response Power Method, Mohammad Royvaran

Theses and Dissertations--Civil Engineering

If the generated vibration in a building exceeds the acceptable limit design for a floor system, it is necessary to identify the source of vibration, a process known as localization. The objective of this study is the localization of stationary vibration sources, and the approach used is the steered response power (SRP) method. This method has already been shown to work well for wireless and acoustical applications to locate transmitter and sound sources, respectively. To the writer’s knowledge, this study is the first application of the SRP method to locate vibration sources using floor vibration measurements. However, because waves behave …

Design Of Structural Stand For High-Precision Optics Microscopy, Sara T. Novell

Master's Theses

Lawrence Livermore National Lab (LLNL) is home to the National Ignition Facility (NIF), the world’s largest and most energetic laser. Each of the 192 beamlines contains dozens of large optics, which require offline damage inspection using large, raster-scanning microscopes. The primary microscope used to measure and characterize the optical damage sites has a precision level of 1 µm. Mounted in a class 100 clean room with a raised tile floor, the microscope is supported by a steel stand that structurally connects the microscope to the concrete ground. Due to ambient vibrations experienced in the system, the microscope is only able …

Dynamic Loading Experimentation And Surface Imaging Of Pressure Vessel Loadcell Fractures, Austin T. Sumner

Honors College Theses

Pressure vessels are very common pieces of equipment in industry and they are used for a variety of applications. It is standard in industry to rest pressure vessels on load cells. For some special cases, the pressure vessels are rested on load cells instead of solid foundation. Pressure vessels and their loadcells are generally designed for static environmental conditions and loading and tend to experience adverse effects when exposed to dynamic environments, such as hurricanes and earthquakes. These adverse-loading conditions cause vibrations and asymmetrical loading on the load cells, which can concurrently cause unexpected failure. This research investigates the effects …

Analytical Approach To Investigation Of Free Vibration Of Thin Rectangular Plate Immersed In Fluid, Resting On Winkler And Pasternak Foundations, Obanishola Sadiq, Gbeminiyi Sobamowo, Saheed Salawu

Karbala International Journal of Modern Science

Dynamic behaviour of free vibration of rectangular plate is investigated. This study considered an analytical approach to investigation of free vibration of thin rectangular plate immersed in fluid, resting on Winkler and Pasternak foundations.The governing nonlinear partial differential equation is analyzed using two-dimensional differential transform method. The accuracy of the analytical solutions obtained is verified with existing results in literature and confirmed in excellent agreement. Thereafter, the analytical solutions are used for investigation of effect of elastic foundation, fluid and aspect ratio on vibrating plate.From the result, it is observed that, increase elastic foundation parameters increases natural frequency, increase aspect …

Structural Health Monitoring Of Composite Parts: A Review, Jacob Pessin

Honors Theses

Structural health monitoring has the potential to allow composite structures to be more reliable and safer, then by using more traditional damage assessment techniques. Structural health monitoring (SHM) utilizes individual sensor units that are placed throughout the load bearing sections of a structure and gather data that is used for stress analysis and damage detection. Statistical time based algorithms are used to analyze collected data and determine both damage size and probable location from within the structure. While traditional calculations and life span analysis can be done for structures made of isotropic materials such as steel or other metals, composites …

Development Of Electromagnetic Friction Dampers For Improving Seismic Performance Of Civil Structures, Mohsen Amjadian

Dissertations and Theses

Energy dissipation is critical to limiting damage to civil structures subjected to extreme natural events such as earthquakes. Friction is one of the most reliable mechanisms of energy dissipation that has been utilized extensively in friction dampers to improve seismic performance of civil structures. Friction dampers are well-known for having a highly nonlinear hysteretic behavior caused by stick-slip motion at low velocities, a phenomenon that is inherent in friction and increases the acceleration response of the structure under control unfavorably, in spite of the fact that the displacement is generally reduced because of the energy dissipation. This increase in acceleration …

Effects Of Tension On Resonant Frequencies Of Strings, Blake Burnett

Senior Theses

This project tests and explores resonance of strings. Since all materials and mechanisms are affected by vibrations, it is important to know the frequencies at which resonance occurs. To explore this subject, strings were used as a model material to test the effect tension has on resonance. The fundamental frequencies and the corresponding modes of resonance were used to analyze the data. The results of this experiment show that increasing tension on a string increases its resonance frequency. Understanding the physics behind resonance frequency allows systems to be designed to take advantage of resonance properties, or to avoid resonance where …

Terahertz Imaging Of Thin Film Layers With Matched Field Processing, Scott Schecklman, Lisa M. Zurk

Electrical and Computer Engineering Faculty Publications and Presentations

Terahertz (THz) time of flight (TOF) tomography systems offer a new measurement modality for non-destructive evaluation (NDE) of the subsurface layers of protective coatings and/or laminated composite materials for industrial, security and biomedical applications. However, for thin film samples, the time-of-flight within a layer is less than the duration of the THz pulse and consequently there is insufficient range resolution for NDE of the sample under test. In this paper, matched field processing (MFP) techniques are applied to thickness estimation in THz TOF tomography applications, and these methods are demonstrated by using measured THz spectra to estimate the the thicknesses …

Development And Validation Of A Tractor Drawbar Force Measurement And Data Acquisition System (Daq), James Roeber, Santosh Pitla, Roger M. Hoy, Joe D. Luck, Michael F. Kocher

Biological Systems Engineering: Papers and Publications

Matching agricultural tractors to implements towed by the drawbar is one of the important aspects of machinery management for ensuring optimum performance and fuel cost savings. A field deployable tractor draft force measurement and data acquisition system was developed and evaluated as part of this research project. A drawbar instrumented to measure draft force in field operating conditions was developed and statically calibrated. The drawbar was calibrated by applying loads from 4.45 to 134 kN using a hydraulic cylinder connected to a 444.8 kN load cell. Testing was conducted with the drawbar installed on a tractor on a concrete track. …

Audio-Based Productivity Forecasting Of Construction Cyclic Activities, Chris A. Sabillon

Electronic Theses and Dissertations

Due to its high cost, project managers must be able to monitor the performance of construction heavy equipment promptly. This cannot be achieved through traditional management techniques, which are based on direct observation or on estimations from historical data. Some manufacturers have started to integrate their proprietary technologies, but construction contractors are unlikely to have a fleet of entirely new and single manufacturer equipment for this to represent a solution. Third party automated approaches include the use of active sensors such as accelerometers and gyroscopes, passive technologies such as computer vision and image processing, and audio signal processing. Hitherto, most …

Lattice Boltzmann Methods For Wind Energy Analysis, Stephen Lloyd Wood

Doctoral Dissertations

An estimate of the United States wind potential conducted in 2011 found that the energy available at an altitude of 80 meters is approximately triple the wind energy available 50 meters above ground. In 2012, 43% of all new electricity generation installed in the U.S. (13.1 GW) came from wind power. The majority of this power, 79%, comes from large utility scale turbines that are being manufactured at unprecedented sizes. Existing wind plants operate with a capacity factor of only approximately 30%. Measurements have shown that the turbulent wake of a turbine persists for many rotor diameters, inducing increased vibration …

Experimental Building Demonstration Model With Viscous Fluid Dampers, Blake Thomas Reeve, Brianna Jean Kufa, Aden Malek Stepanians, Sophie Carmion Ratkovich

Architectural Engineering

The Architectural Engineering major places a heavy emphasis on structural dynamics and the role of wind and seismic loading in building analysis and design. Buildings of high importance that are critical to community function, such as hospitals, often utilize supplemental damping devices like supplemental viscous fluid dampers or base isolators to reduce the overall demands on the structural system. The design and analysis of these dampers are typically not taught at the undergraduate level, and is frequently performed by mechanical engineers, in lieu of structural engineers.

To better understand and research building behavior with supplemental damping devices, our multi-disciplinary team …

Performance Metrics For Depth-Based Signal Separation Using Deep Vertical Line Arrays, Gabriel Paul Kniffin, John Kenneth Boyle, Lisa Zurk, Martin Siderius

Electrical and Computer Engineering Faculty Publications and Presentations

A recent publication by McCargar and Zurk [(2013). J. Acoust. Soc. Am. 133(4), EL320–EL325] introduced a modified Fourier transform-based method for passive source depth estimation using vertical line arrays deployed below the critical depth in the deep ocean. This method utilizes the depth-dependent modulation caused by the interference between the direct and surface-reflected acoustic arrivals, the observation of which is enhanced by propagation through the reliable acoustic path. However, neither the performance of this method nor its limits of applicability have yet been thoroughly investigated. This paper addresses both of these issues; the first by identifying and analyzing the factors …

3d Infrastructure Condition Assessment For Rail Highway Applications, Teng Wang

Theses and Dissertations--Civil Engineering

Highway roughness is a concern for both the motoring public and highway authorities. Roughness may even increase the risk of crashes. Rail-highway grade crossings are particularly problematic. Roughness may be due to deterioration or simply due to the way the crossing was built to accommodate grade change, local utilities, or rail elevation. With over 216,000 crossings in the US, maintenance is a vast undertaking. While methods are available to quantify highway roughness, no method exists to quantitatively assess the condition of rail crossings. Conventional inspection relies on a labor-intensive process of qualitative judgment. A quantifiable, objective and extensible procedure for …

Methodology For Analyzing Epoxy-Cnt Phononic Crystals For Wave Attenuation And Guiding, Madhu Kolati

Dissertations, Master's Theses and Master's Reports

Phononic crystals (PhnCs) control, direct and manipulate sound waves to achieve wave guiding and attenuation. This dissertation presents methodology for analyzing nanotube materials based phononic crystals to achieve control over sound, vibration and stress mitigation. Much of the analytical work presented is in identifying frequency band gaps in which sound or vibration cannot propagate through these PhnCs. Wave attenuation and mitigation analysis is demonstrated using finite element simulation. Engineering principles from current research areas of solid mechanics, solid-state physics, elasto-dynamics, mechanical vibrations and acoustics are employed for the methodology. A considerable effort is put to show that these PhnCs can …

Comparing Various Hardware/Software Solutions And Conversion Methods For Controller Area Network (Can) Bus Data Collection, Samuel E. Marx, Joe D. Luck, Santosh Pitla, Roger M. Hoy

Biological Systems Engineering: Papers and Publications

Various hardware and software solutions exist for collecting Controller Area Network (CAN) bus data. Digital data accuracy could vary based upon different data logging methods (e.g., hardware/software timing, processor timing, etc.). CAN bus data were collected from agricultural tractors using multiple data acquisition solutions to quantify differences among collection methods and demonstrate potential data accumulation rates. Two types of data were observed for this study. The first, CAN bus frame data, represents data collected for each line of hex data sent from an ECU. One issue with frame data is the resulting large file sizes, therefore a second logging format …

Tractor Hydraulic Power Data Acquisition System, J. B.W. Roeber, Santosh Pitla, Michael F. Kocher, Joe D. Luck, Roger M. Hoy

Biological Systems Engineering: Papers and Publications

Tractor hydraulic power is used on a wide range of agricultural implements; however, the availability of operational hydraulic data at points other than full engine throttle position is limited. Operators could utilize this hydraulic data to maximize field efficiency and minimize machinery costs when determining suitable machinery for field operations. A field usable hydraulic test apparatus capable of measuring tractor hydraulic pressure and flow rate data was developed. The goal of this study was to determine if a hydraulic flow and pressure measurement device could be installed on the rear of a tractor to provide implement hydraulic power consumption at …

The Aerodynamic And Dynamic Loading Of A Slender Structure By An Impacting Tornado-Like Vortex: The Influence Of Relative Vortex-To-Structure Size On Structural Loading, Matthew Nicholas Strasser

Graduate Theses and Dissertations

Structural loading produced by an impacting vortex is a hazardous phenomenon that is encountered in numerous applications ranging from the destruction of residences by tornados to the chopping of tip vortices by rotors. Adequate design of structures to resist vortex-induced structural loading necessitates study of the phenomenon that control the structural loading produced by an impacting vortex. This body of work extends the current knowledge base of vortex-structure interaction by evaluating the influence of the relative vortex-to-structure size on the structural loading that the vortex produces. A computer model is utilized to directly simulate the two-dimensional impact of an impinging …

Umass Amherst Green Building Guidelines 2013, Ludmilla Pavlova-Gillham, Ted Mendoza, Ezra Small, Patricia O'Flaherty, Nariman Mostafavi, Mohamed Farzinmoghadam, Somayeh Tabatabaee Pozveh

Ludmilla D Pavlova

Facilities & Campus Services, Sustainable UMass and Campus Planning support sustainability and energy conservation initiatives by providing in-house resources to campus staff as well as designers and contractors working with the University. The UMass Amherst Green Building Guidelines provide a framework for approaching new construction and major renovation projects at UMass Amherst that are undergoing LEED certification by focusing the conversation on green building aspects that are most important to the campus. They are intended to be the beginning of a dynamic conversation between designers, environmental consultants and constructors, university stakeholders, and users of new high performance buildings.

Vibration Of Steel-Framed Floors Supporting Sensitive Equipment In Hospitals, Research Facilities, And Manufacturing Facilities, Di Liu

Theses and Dissertations--Civil Engineering

Floors have traditionally been designed only for strength and deflection serviceability. As technological advances have been made in medical, scientific and micro-electronics manufacturing, many types of equipment have become sensitive to vibration of the supporting floor. Thus, vibration serviceability has become a routinely evaluated limit state for floors supporting sensitive equipment. Equipment vibration tolerance limits are sometimes expressed as waveform peak acceleration, and are more often expressed as narrowband spectral acceleration, or one-third octave spectral velocity.

Current floor vibration prediction methods, such as those found in the American Institute of Steel Construction Design Guide 11, Floor Vibrations Due to Human …

Semi-Active Structural Control Of A 2-Story Shear Building, Alana K. Wilbee, Shirley Dyke

The Summer Undergraduate Research Fellowship (SURF) Symposium

With continuing urban development across the world, it is becoming ever more important to provide increased structural safety against events such as earthquakes and strong winds. The field of structural control has recently been growing to meet these challenges through the use of semi-active control methods, such as the Magnetorheological (MR) Damper. However, due to the non-linearity of the device, the knowledge base surrounding the MR Damper and its various control algorithms still needs to be strengthened before large-scale implementation of this control method can occur. To address these issues, this study will examine a two story benchmark structure using …

Acoustic And Dynamic Characteristics Of A Complex Urban Turnout Using Fibre-Reinforced Foamed Urethane (Ffu) Bearers, Sakdirat Kaewunruen

Sakdirat Kaewunruen

A special track system used to divert a train to other directions or other tracks is generally called ‘railway turnout’. A traditional turnout system includes rails, switches, crossings (special track components), steel plates, fasteners, screw spikes, timber bearers, ballast and formation. The wheel rail contact over the crossing transfer zone has a dip-like shape and can often cause detrimental impact loads on the railway track and its components. The large impact also emits disturbing noises (either impact or ground-borne noise) to railway neighbors. In a brown-field railway track where an existing aged infrastructure requires renewal or maintenance, some physical constraints …

Umass Amherst Green Building Guidelines 2013, Ludmilla Pavlova-Gillham, Ted Mendoza, Ezra Small, Patricia O'Flaherty, Nariman Mostafavi, Mohamed Farzinmoghadam, Somayeh Tabatabaee Pozveh

Campus Planning Reports and Plans

Facilities & Campus Services, Sustainable UMass and Campus Planning support sustainability and energy conservation initiatives by providing in-house resources to campus staff as well as designers and contractors working with the University. The UMass Amherst Green Building Guidelines provide a framework for approaching new construction and major renovation projects at UMass Amherst that are undergoing LEED certification by focusing the conversation on green building aspects that are most important to the campus. They are intended to be the beginning of a dynamic conversation between designers, environmental consultants and constructors, university stakeholders, and users of new high performance buildings.