Mechanical Engineering Commons^™

Design And Validation Of A Variable, Speed-Dependent Resistance Training Method For Muscle Hypertrophy, Alvaro Andres Aracena Alvial

Honors Undergraduate Theses

Muscle disorders and induced muscle atrophy impose critical risks to the well-being of an individual, limiting normal activities of daily living. Several resistance training methods have effectively reversed the progression of muscle atrophy. Weightlifting and hydrotherapy are the two widely practiced schemes for resistance training; however, there is the potential risk of excessive loads exerted on the muscles during weightlifting, and limited accessibility and cost are barriers to hydrotherapy. An alternative is using a resistance band. Some limitations include engaging multiple muscles/joints while only unidirectional resistance is feasible. To address these limitations, a VAriable Resistance Suit (VARS) was designed to …

Development And Application Of 3d Kinematic Methodologies For Biomechanical Modelling In Adaptive Sports And Rehabilitation, Anne Marie Severyn

All Dissertations

Biomechanical analysis is widely used to assess human movement sciences, specifically using three-dimensional motion capture modelling. There are unprecedented opportunities to increase quantitative knowledge of rehabilitation and recreation for disadvantaged population groups. Specifically, 3D models and movement profiles for human gait analysis were generated with emphasis on post-stroke patients, with direct model translation to analyze equivalent measurements while horseback riding in use of the alternative form of rehabilitation, equine assisted activities and therapies (EAAT) or hippotherapy (HPOT). Significant improvements in gait symmetry and velocity were found within an inpatient rehabilitation setting for patients following a stroke, and the developed movement …

Development Of A Novel Haptic Feedback System For Gait Training Applications, Mohsen Alizadeh Noghani

Electronic Theses and Dissertations

Until recently, study and correction of motor or gait functions required costly sensors and measurement setups (e.g., optical motion capture systems) which were only available in laboratories or clinical environments. However, due to (1) the growing availability and affordability of inertial measurement units (IMUs) with high accuracy, and (2) progress in wireless, high bandwidth, and energy-efficient networking technologies such as Bluetooth Low Energy (BLE), it is now possible to measure and provide feedback in real-time for biomechanical parameters outside of those specialized settings. To enable gait training without an expert who can provide verbal feedback, augmented feedback, which is divided …

Composite Pegboard, Asa J. Cusick, Luis Corrales, Joelle Hylton, Wyatt Pauley

Mechanical Engineering

Many of those with mobility limitations who are told they will need a wheelchair for the rest of their lives can actually begin to stand and walk again given the proper tools and support. The current design for a wheelchair seeking to support this process is overly complex, heavy, and exhibits some features that could potentially pose a serious health hazard to those using it. The scope of this project is to aid in the design of an adaptable composite wheelchair frame that can be both lightweight and strong, while still allowing for physical diversity of potential users. Through research …

Design And Implementation Of A Modular Human-Robot Interaction Framework, Michael J. Juri

Master's Theses

With the increasing longevity that accompanies advances in medical technology comes a host of other age-related disabilities. Among these are neuro-degenerative diseases such as Alzheimer's disease, Parkinson's disease, and stroke, which significantly reduce the motor and cognitive ability of affected individuals. As these diseases become more prevalent, there is a need for further research and innovation in the field of motor rehabilitation therapy to accommodate these individuals in a cost-effective manner. In recent years, the implementation of social agents has been proposed to alleviate the burden on in-home human caregivers. Socially assistive robotics (SAR) is a new subfield of research …

Design And Analysis Of A 3d-Printed, Thermoplastic Elastomer (Tpe) Spring Element For Use In Corrective Hand Orthotics, Kevin Thomas Richardson

Theses and Dissertations--Mechanical Engineering

This thesis proposes an algorithm that determine the geometry of 3D-printed, custom-designed spring element bands made of thermoplastic elastomer (TPE) for use in a wearable orthotic device to aid in the physical therapy of a human hand exhibiting spasticity after stroke. Each finger of the hand is modeled as a mechanical system consisting of a triple-rod pendulum with nonlinear stiffness at each joint and forces applied at the attachment point of each flexor muscle. The system is assumed quasi-static, which leads to a torque balance between the flexor tendons in the hand, joint stiffness and the design force applied to …

Robot Control For Remote Ophthalmology And Pediatric Physical Rehabilitation, Melissa Morris

FIU Electronic Theses and Dissertations

The development of a robotic slit-lamp for remote ophthalmology is the primary purpose of this work. In addition to novel mechanical designs and implementation, it was also a goal to develop a control system that was flexible enough to be adapted with minimal user adjustment to various styles and configurations of slit-lamps. The system was developed with intentions of commercialization, so common hardware was used for all components to minimize the costs. In order to improve performance using this low-cost hardware, investigations were made to attempt to achieve better performance by applying control theory algorithms in the system software. Ultimately, …

Design And Evaluation Of Pediatric Gait Rehabilitation Robots, Cale J. Stolle

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Gait therapy methodologies were studied and analyzed for their potential for pediatric patients. Using data from heel, metatarsal, and toe trajectories, a nominal gait trajectory was determined using Fourier transforms for each foot point. These average trajectories were used as a basis of evaluating each gait therapy mechanism. An existing gait therapy device (called ICARE) previously designed by researchers, including engineers at the University of Nebraska-Lincoln, was redesigned to accommodate pediatric patients. Unlike many existing designs, the pediatric ICARE did not over- or under-constrain the patient’s leg, allowing for repeated, comfortable, easily-adjusted gait motions. This design was assessed under clinical …

Optimizing The Rehabilitation Of Elbow Lateral Collateral Ligament Injuries, Ranita Harpreet Kaur Manocha

Electronic Thesis and Dissertation Repository

Elbow lateral collateral ligament (LCL) injuries frequently arise following trauma, and can result in disabling instability. Typically such injuries are managed with immobilization followed by a graduated exercise regime; however there is minimal biomechanical evidence to support current treatment protocols. This investigation examines the in vitro effectiveness of several rehabilitation techniques using a custom elbow motion simulator. It was found that active range of motion is safest in the overhead position (n = 7). Early motion in this position may reduce the incidence of elbow stiffness without compromising ligament healing following LCL injury. Forearm pronation and active motion stabilize …

Development Of A Wearable Mechatronic Elbow Brace For Postoperative Motion Rehabilitation, Anastasiia Kyrylova

Electronic Thesis and Dissertation Repository

This thesis describes the development of a wearable mechatronic brace for upper limb rehabilitation that can be used at any stage of motion training after surgical reconstruction of brachial plexus nerves. The results of the mechanical design and the work completed towards finding the best torque transmission system are presented herein. As part of this mechatronic system, a customized control system was designed, tested and modified. The control strategy was improved by replacing a PID controller with a cascade controller. Although the experiments have shown that the proposed device can be successfully used for muscle training, further assessment of the …

A Continous Rotary Actuation Mechanism For A Powered Hip Exoskeleton, Matthew C. Ryder

Masters Theses

This thesis presents a new mechanical design for an exoskeleton actuator to power the sagittal plane motion in the human hip. The device uses a DC motor to drive a Scotch yoke mechanism and series elasticity to take advantage of the cyclic nature of human gait and to reduce the maximum power and control requirements of the exoskeleton. The Scotch yoke actuator creates a position-dependent transmission that varies between 4:1 and infinity, with the peak transmission ratio aligned to the peak torque periods of the human gait cycle. Simulation results show that both the peak and average motor torque can …

An Experimental Study On Passive Dynamic Walking, Philip Andrew Hatzitheodorou

USF Tampa Graduate Theses and Dissertations

In this study, a previously designed passive dynamic walker (PDW) is built out of aluminum and plastic. The aim of the study was to produce an asymmetrical PDW and to compare the results to a computer simulation to validate the mathematical model. It also aimed at identifying the limitations of using additive manufacturing to create components for a PDW as well as gain insights on asymmetric systems.

Beginning with a five mass kneed model, parameters were varied to produce up to a nine mass kneed model solution. The nine mass model allows more variability in added mass locations and separates …

Low-Cost Strider For Guatemala, Nicole Catherine Cooper, Gonzalo Hernandez, Jared W. Tower

Mechanical Engineering

The purpose of this project was to create a strider, a type of standing rehabilitation device, for children in developing countries who have trouble walking and supporting their full body weight. The project was initially brought to us by Cal Poly professor Brian Self, who had visited a clinic in San Marcos and determined that there were children there who had difficulties with walking and were a need for a rehabilitation device. The team discussed the problem with Dr. Self, Matt Robinson (a local San Luis Obispo prosthetist), and Cal Poly physics professor Pete Schwartz, all of whom had visited …

Development Of A Robotic Platform For Upper Limb Rehabilitation, Stephen Curran, Nigel Kent, David Kennedy, James Conlon

Conference Papers

The aim of this project is to develop a rehabilitation robot intended for use in a non-specialised or domestic setting. Robots have been shown to have a positive effect on limb rehabilitation and developing rehabilitation robots for use outside of specialist rehabilitation centres could be beneficial in terms of access to, intensity and cost of treatment. The device is intended for the rehabilitation of the shoulder/elbow region of the upper limbs. The design requirements for such a device mean that it must be low cost, portable, robust and have a detailed focus on safety. Other areas of interest pertaining to …