Mechanical Engineering Commons^™

Literature Review On Modeling Of Density Difference Pumping Strategy For Geothermal Applications, Lucas A. Ware

Graduate Theses, Dissertations, and Problem Reports

The utilization of geothermal ground heat sources has been demonstrated at both large and small scales across the world. However, methods of extraction of the hot working fluids are often a source of energy inefficiency and high capital expense. Current techniques to extract geothermal fluids rely on mechanically and electrically driven down-hole components that require maintenance on a regular basis. In providing a solution, one approach that reduces complexity, decreases maintenance, and allows access to fluids at greater depth is an airlift approach. The airlift approach relies on injection of gas at a depth within a geothermal well to lift …

Detection And Classification Of Vibrating Objects In Sar Images, Francisco German Perez Venegas

Electrical and Computer Engineering ETDs

The vibratory response of buildings and machines contains key information that can be exploited to infer their operating conditions and to diagnose failures. Furthermore, since vibration signatures observed from the exterior surfaces of structures are intrinsically linked to the type of machinery operating inside of them, the ability to monitor vibrations remotely can enable the detection and identification of the machinery.

This dissertation focuses on developing novel techniques for the detection and M-ary classification of vibrating objects in SAR images. The work performed in this dissertation is conducted around three central claims. First, the non-linear transformation that the micro-Doppler return …

Analysis And Control Of Fiber-Reinforced Elastomeric Enclosures (Frees), Soheil Habibian

Master’s Theses

While rigid robots are extensively used in various applications, they are limited in the tasks they can perform and can be unsafe in close human-robot interactions. Soft robots on the other hand surpass the capabilities of rigid robots in several ways, such as compatibility with the work environments, degrees of freedom, manufacturing costs, and safe interactions with the environment. This thesis studies the behavior of Fiber-Reinforced Elastomeric Enclosures (FREEs) as a particular type of soft pneumatic actuator that can be used in soft manipulators. A dynamic lumped-parameter model is created to simulate the motion of a single FREE under various …

Development Of Novel Models To Study Deep Brain Effects Of Cortical Transcranial Magnetic Stimulation, Farheen Syeda

Theses and Dissertations

Neurological disorders require varying types and degrees of treatments depending on the symptoms and underlying causes of the disease. Patients suffering from medication-refractory symptoms often undergo further treatment in the form of brain stimulation, e.g. electroconvulsive therapy (ECT), transcranial direct current stimulation (tDCS), deep brain stimulation (DBS), or transcranial magnetic stimulation (TMS). These treatments are popular and have been shown to relieve various symptoms for patients with neurological conditions. However, the underlying effects of the stimulation, and subsequently the causes of symptom-relief, are not very well understood. In particular, TMS is a non-invasive brain stimulation therapy which uses time-varying magnetic …

Thermoelectric System Modeling And Design, Buddhima Pasindu Gamarachchi

Boise State University Theses and Dissertations

Thermoelectric generators (TEGs) convert heat to electricity by way of the Seebeck effect. TEGs have no moving parts and are environmentally friendly and can be implemented with systems to recover waste heat. This work examines complete thermoelectric systems, which include the (TEG) and heat exchangers or heat sinks attached to the hot and cold sides of the TEG to maintain the required temperature difference across the TEG. A 1-D steady state model is developed to predict the performance of a TEG given the required temperatures and device dimensions. The model is first validated using a 3-D model and then is …

Turbulent Spray Combustion Modeling Using Direct Integration Of Chemistry And Flamelet Generated Manifolds, Ashraya Goyal

Wayne State University Theses

Turbulent spray combustion of n-dodecane was modeled at engine relevant conditions using various combustion models (Direct Integration of Chemistry and Flamelet Generated Manifolds) and turbulence models (Dynamic Structure Large Eddy Simulation and RNG Reynolds-Averaged Naiver-Stokes). A recently developed n-dodecane mechanism was utilized and the turbulent spray was simulated at various combustion chamber initial gas temperature and pressure conditions. Mesh with size of 31 microns was utilized to resolve small eddies around the spray. The pressure-based ignition delay, flame lift-off length, and spray and jet penetrations were studied and compared with experimental measurements. The Direct Integration of Chemistry and Flamelet Generated …

Task Specific Uncertainty In Coordinate Measurement, R. G. Wilhelm, R. Hocken, H. Schwenke

Department of Mechanical and Materials Engineering: Faculty Publications

Task specific uncertainty is the measurement uncertainty associated with the measurement of a specific feature using a specific measurement plan. This paper surveys techniques developed to model and estimate task specific uncertainty for coordinate measuring systems, primarily coordinate measuring machines using contacting probes. Sources of uncertainty are also reviewed.