Mechanical Engineering Commons^™

Nozzle Clogging Prevention And Analysis In Cold Spray, Alden Foelsche

Masters Theses

Cold spray is an additive manufacturing method in which powder particles are accelerated through a supersonic nozzle and impinged upon a nearby substrate, provided they reach their so-called critical velocity. True to its name, the cold spray process employs lower particle temperatures than other thermal spray processes while the particle velocities are comparably high. Because bonding occurs mostly in the solid state and at high speeds, cold spray deposits are distinguished for having low porosity and low residual stresses which nearly match those of the bulk material.

One complication with the cold spray process is the tendency for nozzles to …

Electroplating Of Copper On Tungsten Powder, Richard Berdos

Masters Theses

Strengthening, resistant and shielding properties, to name a few, can be achieved by implementing a surface material coating onto an engineering component. Various elements of these compounded parts can augment the functionality of the part, such as, increased life time and more interactive surfaces. Tungsten has proven to be a challenge to plate with other metals, but if done correctly, the results can allow for the cold spray of tungsten. Cold spraying tungsten particles alone provides a challenge because the powder is too hard and instead of adhering, it erodes the surface it is attempting to plate. Coating tungsten in …

High Strain Rate Dynamic Response Of Aluminum 6061 Micro Particles At Elevated Temperatures And Varying Oxide Thicknesses Of Substrate Surface, Carmine Taglienti

Masters Theses

Cold spray is a unique additive manufacturing process, where a large number of ductile metal micro particles are deposited to create new surface coatings or free-standing structures. Metallic particles are accelerated through a gas stream, reaching velocities of over 1 km/s. Accelerated particles experience a high-strain-rate microscopic ballistic collisions against a target substrate. Large amounts of kinetic energy results in extreme plastic deformation of the particles and substrate. Though the cold spray process has been in use for decades, the extreme material science behind the deformation of particles has not been well understood due to experimental difficulties arising from the …

Influence Of Impact Conditions On Feedstock Deposition Behavior Of Cold-Sprayed Fe-Based Metallic Glass, Constance Ziemian, Wendelin Wright, David E. Cipoletti

Faculty Journal Articles

Cold spray is a promising method by which to deposit dense Fe-based metallic glass coatings on conventional metal substrates. Relatively low process temperatures offer the potential to prevent the crystallization of amorphous feedstock powders while still providing adequate particle softening for bonding and coating formation. In this study, Fe48 Mo14 Cr15 Y2 C15 B6 powder was sprayed onto a mild steel substrate, using a variety of process conditions, to investigate the feasibility of forming well-bonded amorphous Fe-based coatings. Particle splat adhesion was examined relative to impact conditions, and the limiting values of temperature and velocity associated with successful softening and …

Simulation Of Gas Dynamic Cold Spray Process, Sai Rajkumar Vadla

Electronic Theses and Dissertations

The utilization of computational fluid dynamics (CFD) as a study tool in the aerodynamics and turbomachinery industry reinforces efficiency in the design of aircraft or for understanding the flow through pipes. CFD offer tools to model different geometries and perform a more extensive study of the flow phenomena. This gives the opportunity to model a variety of geometries and analyze their behavior under different operating conditions. A similar approach can be applied to coating technologies. Coating technologies play an essential role in the manufacturing industry. Their ability to form layers of specific materials onto engineering components to enhance mechanical and …

Electroless Deposition & Electroplating Of Nickel On Chromium-Nickel Carbide Powder, Jeffrey Rigali

Masters Theses

Engineered components can gain desirable properties when coated with surface materials. Wear-resistant coatings can improve the performance of contacting surfaces and allow for an extended life of the parts. Hard chromium has been the plating material of choice for certain wear and corrosion- resistant coatings because of its desirable combination of chemical resistance, adhesion, and mechanical properties. However, hexavalent chromium, a component of the process for applying hard chromium coatings, has been recognized by the EPA as having hazardous health and environmental impacts. Existing and planned environmental regulations restricts the use of process chemicals containing hexavalent chromium ions. This substantiates …

Numerical Simulation Of High Velocity Impact Of A Single Polymer Particle During Cold Spray Deposition, Sagar P. Shah

Masters Theses

Abstract

The cold spray process is an additive manufacturing technology primarily suited for ductile metals, and mainly utilized in coating surfaces, manufacturing of freeform parts and repair of damaged components. The process involves acceleration of solid micro-particles in a supersonic gas flow and coating build-up by bonding upon high velocity impact onto a substrate. Coating deposition relies on the kinetic energy of the particles. The main objective of this study was to investigate the mechanics of polymer cold spray process and deformation behavior of polymers to improve technological implementation of the process.

A finite element model was created to simulate …