Mechanical Engineering Commons^™

Microstructure, Wetting Angle And Corrosion Of Aluminum-Silicon Alloys, Shvetashva Suri

Theses and Dissertations

In this study the effect of composition, surface roughness and water droplet size on contact angle and corrosion properties of cast Aluminum-Silicon alloys containing Si from 5% to 50% have been examined. The water contact angle was measured on a given sample using a goniometer. In addition, the effect of surface roughness and droplet size on contact angle has been measured for alloys at a fixed composition. The microstructures can be found in this report with sizes of primary and eutectic Silicon as well as inter-particle spacing between Silicon. Contact angle measurements are accompanied with a photographic validation of the …

Study On The Impact Abrasive Wear Of New Super-High Manganese Steel, Wenyan Wang

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Simulation Of Two Kinds Of Hot Stamping Processes Of Ultra High-Strength Steel, Hao Zhao, Zhongwen Xing, Hongliang Yang

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Void Closure And The Sensitivity Analysis Of The Process Parameters During Forging Of Large Steel Ingot, Bo Jiang, Yazheng Liu, Jianlin Sun, Guanglei Liu, Zhilin Wang, Zhigang Zhao

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Weld Thermal Simulation Of Crmov With Pwht In Type Iv Region, Bin Xu

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Flow Stress And Microstructure Models Of Alloys, Lars-Erik Lindgren

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Secondary Electron Emission From Plasma Processed Accelerating Cavity Grade Niobium, Miloš Bašović

Mechanical & Aerospace Engineering Theses & Dissertations

Advances in the particle accelerator technology have enabled numerous fundamental discoveries in 20th century physics. Extensive interdisciplinary research has always supported further development of accelerator technology in efforts of reaching each new energy frontier.

Accelerating cavities, which are used to transfer energy to accelerated charged particles, have been one of the main focuses of research and development in the particle accelerator field. Over the last fifty years, in the race to break energy barriers, there has been constant improvement of the maximum stable accelerating field achieved in accelerating cavities. Every increase in the maximum attainable accelerating fields allowed for higher …

The Effects Of Thermal Procedure On Transformation Temperature, Crystal Structure And Microstructure Of Cu-Al-Co Shape Memory Alloy, Y. Aydoğdu, M. Kök, F. Dağdelen, A. Aydoğdu, Ali S. Turabi, Haluk E. Karaca

Mechanical Engineering Faculty Publications

The purpose of this study is to investigate the effects of different thermal procedures of the Cu-Al-Co shape memory alloy on its crystal structure, transformation temperature and microstructure. The alloys were subjected to a heat treatment and then cooling was applied at four different conditions. After the thermal process, XRD, DSC, optical microscopy and micro-hardness measurements were carried out. The experimental studies showed that crystal structure, microstructure and transformation temperature of Cu-Al-Co alloy were changed from the cooling conditions.

Cryogenic Processing Of Al 7050-T7451 Alloy For Improved Surface Integrity, Bo Huang

Theses and Dissertations--Mechanical Engineering

Al 7050-T7451 alloy with good combinations of strength, stress corrosion cracking resistance and toughness, is used broadly in the aerospace/aviation industry for fatigue-critical airframe structural components. However, it is also considered as a highly anisotropic alloy as the crack growth behavior along the short transverse direction is very different from the one in the long transverse direction, due to the inhomogeneous microstructure with the elongated grains distributed in the work material used in the sheet/plate applications. Further processes on these materials are needed to improve its mechanical and material properties and broaden its applications.

The material with ultra-fine or nano …

An Adapted Approach To Process Mapping Across Alloy Systems And Additive Manufacturing Processes, Luke Charles Sheridan

Browse all Theses and Dissertations

The continually growing market for metal components fabricated using additive manufacturing (AM) processes has called for a greater understanding of the effects of process variables on the melt pool geometry and microstructure in manufactured components for various alloy systems. Process Mapping is a general approach that traces the influence of process parameters to thermal behavior and feature development during AM processing. Previous work has focused mainly on Ti-6Al-4V (Ti64), but this work uses novel mathematical derivations and adapted process mapping methodologies to construct new geometric, thermal, and microstructural process maps for Ti64 and two nickel superalloy material systems. This work …

Elucidating The Role Of Microstructure, Texture, And Microtexture On The Dwell Fatigue Response Of Ti-6al-4v, Alec Mitchell Blankenship

Browse all Theses and Dissertations

Ambient temperature dwell sensitivity is known to be deleterious to the fatigue response of near-alpha titanium alloys. Dwell fatigue refers to the presence of a sustained hold at peak stress as opposed to the continuous variation of normal cyclic fatigue loading. This reduction in failure life-times from dwell loading is attributed to early crack nucleation and faster crack propagation. The degradation is the result of plastic anisotropy on the microstructural scale along with tendency of titanium alloys to creep at low temperatures at stresses well below the 0.2% offset yield strength. Despite being the most widely used titanium alloy, Ti-6Al-4V …