Mechanical Engineering Commons^™

Photovoltaic Cooking In The Developing World, Tyler Watkins, Christopher O'Day, Omar Arriaga

Mechanical Engineering

The challenge of clean cooking is faced by hundreds of millions of people worldwide. We present a cooking technology consisting of a solar panel directly connected to an electric heater in a well-insulated chamber. Assuming continued decrease in solar panel prices, we anticipate that in a few decades Solar Electric Cooking technologies will be the most common cooking technology for the poor. Appropriate use of insulation reduces the power demand making low-power Insulated Solar Electric Cooking systems already cost competitive.

Thermal Transport In Lithium Ion Batteries: An Experimental Investigation Of Interfaces And Granular Materials, Aalok Jaisheela Uday Gaitonde

Open Access Theses

Increasing usage and recent accidents due to lithium-ion (Li-ion) batteries exploding or catching on fire has inspired research on the characterization and thermal management of these batteries. In cylindrical 18650 cells, heat generated during the battery's charge/discharge cycle is poorly dissipated to the surrounding through its metallic case due to the poor thermal conductivity of the jelly roll, which is spirally wound with many interfaces between electrodes and the polymeric separator. This work presents a technique to measure the thermal conduction across the metallic case-plastic separator interface, which ultimately limits heat transfer out of the jelly roll.

The polymeric separator …

Impedance-Resolved Performance And Durability In Redox Flow Batteries, Alan Michael Pezeshki

Doctoral Dissertations

The realization of redox flow batteries (RFBs) as a grid-scale energy solution depends on improving the performance and lifetime of the technology to decrease the high capital costs. The electrodes are a key component in the RFB; performance enhancement is often achieved through chemical or thermal treatments of commercially available porous carbon materials.

This dissertation uses impedance spectroscopy-based methods to gain insight into performance and durability in RFBs, enabling intelligent cell design. Initial work focused on understanding the impact of improved electrode and membrane properties on system performance. An accelerated stress test was then developed that can be used to …

Fundamental Studies Of Electrochemical Reactions And Microfluidics In Proton Exchange Membrane Electrolyzer Cells, Jingke Mo

Doctoral Dissertations

In electrochemical energy devices, including fuel cells, electrolyzers and batteries, the electrochemical reactions occur only on triple phase boundaries (TPBs). The boundaries provide the conductors for electros and protons, the catalysts for electrochemical reactions and the effective pathways for transport of reactants and products. The interfaces have a critical impact on the overall performance and cost of the devices in which they are incorporated, and therefore could be a key feature to optimize in order to turn a prototype into a commercially viable product. For electrolysis of water, proton exchange membrane electrolyzer cells (PEMECs) have several advantages compared to other …

Investigation Of Localized Performance And Gas Evolution In All-Vanadium Redox Flow Batteries Via In-Situ Distributed Diagnostic Techniques, Jason Thomas Clement

Doctoral Dissertations

All-vanadium redox flow batteries (VRFBs) are an emerging grid-scale energy storage technology; however, enhancements in terms of performance, efficiency, durability, and cost are required before it can become commercially viable. These improvements are achievable through the development of advanced materials, superior architecture, and ultimately a deeper fundamental understanding of the influence of various phenomena and operational parameters on cell performance. There currently are a lack of in-situ experimental diagnostic techniques which can help in achieving this fundamental understanding.

Two separate distributed diagnostic techniques were developed in this work: in-plane current distribution, and neutron radiography. Localized current distribution measurements can identify …

Theoretical Modeling, Experimental Observation, And Reliability Analysis Of Flow-Induced Oscillations In Offshore Wind Turbine Blades, Pariya Pourazarm

Doctoral Dissertations

Offshore wind energy has been growing rapidly due to its capacity for utilizing much larger turbines and thus higher power generation compared to onshore. With the increasing size of offshore wind turbine rotors, the design criteria used for the blades may also evolve. Increased flexibility in blades causes them to be more susceptible to experiencing flow-induced instability. One of the destructive aero-elastic instabilities that can occur in flexible structures subjected to aerodynamic loading is coupled-mode flutter. Coupled-mode flutter instability has not been a design driver in the current wind turbine blades, however, considering the industry tendency in utilizing longer and …

Polymer And Small Molecule Designs For Anion Conducting Membranes: Connected Ion-Channel Morphologies And Highly Alkaline Stable Ammonium Cations, Sedef P. Ertem

Doctoral Dissertations

Fuel cells are one of the oldest sustainable energy generation devices, converting chemical energy into electrical energy via reverse-electrolysis reactions. With the rapid development of polymer science, solid polymer electrolyte (SPE) membranes replaced the conventional liquid ion transport media, rendering low-temperature fuel cells more accessible for applications in portable electronics and transportation. However, SPE fuel cells are still far from commercialization due to high operation cost, and insufficient lifetime and performance limitations. Anion exchange membrane fuel cells (AEMFCs) are inexpensive alternatives to current proton exchange membrane fuel cell (PEMFC) technology, which relies on utilizing expensive noble-metal catalysts and perfluorinated SPE …

Modeling Pyrolysis Of Large Coal Particles With Many Species, Jianqing Li

Master's Theses (2009 -)

Coal currently supplies 40% of the world’s electricity needs, and is one of the most important energy sources. As the initial stage of coal combustion, pyrolysis is a thermal decomposition process which converts coal into light gases and tars, which are subsequently consumed in combustion reactions, as well as solid char. Recently there has been interest in using slow pyrolysis as a stand-alone process for the production of chemicals and fuels from large (mm-scale) coal particles. Simulations can be used to efficiently study the impact of pyrolysis conditions on gas, tar and char yields, as well as gas and tar …

Parametric And Design Analysis On Thermoelectric Generators, Shouyuan Huang

Open Access Theses

In facing the limited energy source reserves and environmental problems, thermoelectric generators (TEGs) are one of the promising waste heat recovery systems. The modern TEGs for exhaust stream (e.g. from automobiles) can improve the fuel economy by around 5%, taking advantage of the recent developed thermoelectric (TE) materials.

In this work, we aimed at designing a TEG as an add-on module for a gas-phase heat exchanger with maximized power output, and without negative impact (e.g. maintaining a minimum heat dissipation rate from the hot side). We first developed a parametric optimization algorithm using response surface method (RSM) and genetic algorithm …

Thermoelectric Material Property Measurement For Flexible Films, Courtney Hollar

Boise State University Theses and Dissertations

The market for wearable electronics and implantable medical devices continues to grow. Within the next several years, the wearable electronic and implantable medical devices market will reach $31.2 billion and $73.9 billion, respectively. Currently, the most commonly used power source is the rigid lithium ion battery. In order to further optimize the devices, flexible autonomous power sources, such as thermoelectric generators, can replace traditional battery systems.

Flexible thermoelectric films were created using a wet deposition approach and synthesized into ink suitable for either spin coating or screen printing. This study focuses on Seebeck coefficient, electrical conductivity, and thermal conductivity measurements. …

Wind Farm Wake Modeling And Analysis Of Wake Impacts In A Wind Farm, Yujia Hao

Doctoral Dissertations

More and more wind turbines have been grouped in the same location during the last decades to take the advantage of profitable wind resources and reduced maintenance cost. However wind turbines located in a wind farm are subject to a wind field that is substantially modified compared to the ambient wind field due to wake effects. The wake results in a reduced power production, increased load variation on the waked turbine, and reduced wake farm efficiency. Therefore the wake has long been an important concern for the wind farm installation, maintenance, and control. Thus a wake simulation tool is required. …

Wake Character In The Wind Turbine Array: (Dis-)Organization, Spatial And Dynamic Evolution And Low-Dimensional Modeling, Nicholas Michael Hamilton

Dissertations and Theses

To maximize the effectiveness of the rapidly increasing capacity of installed wind energy resources, new models must be developed that are capable of more nuanced control of each wind turbine so that each device is more responsive to inflow events. Models used to plan wind turbine arrays and control behavior of devices within the farm currently make questionable estimates of the incoming atmospheric flow and update turbine configurations infrequently. As a result, wind turbines often operate at diminished capacities, especially in arrays where wind turbine wakes interact and inflow conditions are far from ideal. New turbine control and wake prediction …

The Effect Of Mesh-Type Bubble Breakers On Two-Phase Vertical Co-Flow, Alan Kalbfleisch

Electronic Thesis and Dissertation Repository

It is proposed that mesh-type bubble breakers can be used in two-phase gas-liquid vertical cocurrent pipe flow to enhance the heat and mass transfer rates. Two experimental studies were performed to investigate the effect of mesh-type bubble breakers with varying geometries on two-phase flow behaviour. The first used highspeed imaging to measure bubble size and observe the resulting flow regime for two-phase vertical co-flow consisting of air and water. A Froude number correlation that can be used to predict the bubble size generated by mesh-type bubble breakers is proposed. Flow regime maps for two-phase flow in the presence of bubble …

Fluid Analysis In Solar Heat Pipes, Ben Krumholz, Michael Agavo, William Dundon

Mechanical Engineering

Evacuated tube solar collectors are efficient systems that use heat pipes to facilitate heat transfer. They use incoming solar radiation to heat water. Professor Mason Medizade tasked the team with choosing a component of the system to research and test its influence on system performance. The team investigated the working fluid that runs through the heat pipes. Distilled water, acetone, and ethanol at a range of fill volumes form 1 mL to 11 mL were tested. The team's goal was to find a volume for each fluid to maximize performance of the system. Performance was defined as average temperature rise …

Disc Brake Energy Conversion, D. Coleman Badgley, Jeffrey W. Powell

Mechanical Engineering

The original goal of this project was to complete the design and building of a disc brake energy conversion project started by a former senior project team, and then spend a majority of the year performing testing in order to see if the device could be used to accurately calculate the Joule's constant. However, due to unforeseen complications and obstacles, the design and manufacturing portion of the project ended up taking much longer than anticipated. A majority of this time was spent designing the hydraulic plumbing system that would actuate the brakes. The previous team purchased some hydraulic parts and …

Prosthetic Socket Cooling System, Benjamin K. Kraw, Kathy Ha, Derek Piastrelli, Cuong Lai

Mechanical Engineering

A team of four senior-level undergraduate students in the Interdisciplinary Senior Project Design course in the Engineering Department of California Polytechnic State University: San Luis Obispo have worked to develop a prosthetic socket cooling system, namely for veteran Taylor Morris and exclusively for a transfemoral prosthetic socket, under the Quality of Life+ Laboratory. This cooling system will utilize the thermoelectric effect known as the Peltier effect to transmit heat generated from the residual limb to the surrounding environment by means of forced convection over small aluminum heat sinks. Two measurement devices have also been developed to, one, measure the heat …

Me 350 Air Conditioning Experiment, Joshua Baida, Ellie Hallner, Tyler Eschenbach

Mechanical Engineering

In keeping with Cal Poly's focus on physically applying the concepts learned in the classroom, our team of engineering students has compiled a laboratory experiment displaying the basic thermodynamic cycle found in air conditioning systems. This vapor compression cycle is displayed on a visualization board that features all four major components of the system: the compressor, the evaporator, the condenser, and the throttling valve. Students will take measurements of temperature and pressure at each stage in the cycle and also gauge the power draw from the compressor to gain an understanding of how performance and electricity cost come into play …

Gasoline Confined In Nano-Porous Media, Matthew Giso

Honors Theses

The heat of combustion was determined for gasoline confined in nano-porous media of differing pore size by bomb calorimetry. The heat of combustion of the confined fuels was comparable to that of bulk within the experimental uncertainty. This suggests that all of the confined fuel burns without any flame quenching and no chemical interactions at the interface between pore walls and fuel mitigate combustion.

Heat Of Fusion Of Primary Alcohol Confined In Nanopores, Harrisonn Griffin

Honors Theses

Melting behavior of physically confined 1-decanol in nano porous silica was probed using a Differential Scanning Calorimeter (DSC). In agreement with the Gibbs-Thomson prediction, we observe that the melting temperature of the confined 1-decanol scales inversely with the physical size of the pores. Contrary to the assumption used in developing the Gibbs-Thomson equation, however, the apparent heat of fusion decreases as the pore size decreases. Previously, several models have been proposed where interfacial layers of molecules do not participate in the phase transition and thereby would not contribute to the heat of fusion. While these could reconcile the seeming contradiction, …

How Can Occupancy Modeling And Occupancy Sensors Reduce Energy Usage In Academic Buildings: An Application Approach To University Of San Francisco, Paloma R. Duong

Master's Projects and Capstones

Buildings are amongst the highest energy consumers relative to industry and transportation. They account for 40% of the world’s energy consumption, due to the need for lighting, equipment, heating, cooling and ventilation. Academic buildings are multi-purpose buildings that create a challenge on energy reduction. Most are old and have fixed occupancy schedules, resulting in high energy consumption because these buildings experience significant occupancy variation throughout the day. Five academic buildings were analyzed; their building information, energy consumption data and methods to project energy savings have been analyzed. The case studies presented different strategies on predicting energy savings, but these have …

Energy Models Of The Txaire Houses, Tajudeen Amadu Annafi

Mechanical Engineering Theses

Model calibration is important as its functions improve building models. A calibrated model of the TxAIRE Houses #1 and #2 have been developed using the OpenStudio software. The model was developed and calibrated with data of the year 2014 but can be used predict electricity consumption of any year.

An actual meteorological year (AMY) weather file was also created for the houses which was used for calibration. The data used to develop this weather file were measured on-site which improved the accuracy of the model. It was found that an error difference of -1.0 % and -4.2 % occurred between …

Modeling And Measurement Of Evaporation From Frequently Tilled Sandy Soils, Nicholas R. Lawson

Electronic Theses and Dissertations

Moisture observation and control is the single largest factor that controls the mechanical properties of sand based surfaces used for thoroughbred horse racing. Currently the moisture content is estimated based on the experience and expertise of the superintendent and water is added as needed based on experience. While extensive modelling has been done on moisture loss from a range of soils with crop covers in agronomy, currently no method exists to estimate the evaporation from a surface that is tilled many times a day and remains in a partially compacted state. This thesis develops an evaporation model based on real …

Characterization Of A Wind Tunnel For Use In Offshore Wind Turbine Development With Mitigation Measures For The Wall Effect Of Proximal Structures, James Newton

Electronic Theses and Dissertations

This thesis supports the development of the Harold Alfond W² Ocean Engineering Laboratory constructed at the University of Maine through several investigations conducted with a one-third scale wind generation system. The scale wind generator is first tested in what is considered an open-circuit wind tunnel configuration to determine the influence proximal building walls of a facility housing such a device may have on the consistency and capacity of a wind generator. Turbine performance testing with the wind generator to identify any susceptibility to proximal wall influence is also conducted. This is of interest as the full-scale system will operate …

Inter-Droplet Membranes For Mechanical Sensing Applications, Nima Tamaddoni Jahromi

Doctoral Dissertations

This dissertation combines self-assembly phenomena of amphiphilic molecules with soft materials to create and characterize mechanoelectrical transducers and sensors whose sensing elements are thin-film bioinspired membranes comprised of phospholipids or amphiphilic polymers. We show that the structures of these amphiphilic molecules tune the mechanical and electrical properties of these membranes. We show that these properties affect the mechanoelectrical sensing characteristic and range of operation of these membrane transducers. In the experiments, we construct and characterize a membrane-based hair cell embodiment that enables the membrane to be responsive to mechanical perturbations of the hair. The resulting oscillations of membranes formed between …

Least Cost Analysis For Solar Photovoltaic Maintenance Of The Wmu Miller Auditorium Array, Kelsey Pitschel

Honors Theses

The solar photovoltaic array at Miller Auditorium is a 50 kW DC system that has relied on five seasonal angle adjustments and no cleaning measures to reach an average of 64.7 MWh annual energy generation since 2012 1 . This amount of energy generation yields $7,046 in annual energy savings based on current market pricing for end use electricity of $0.1089/kWh 2 . The current adjustment schedule based on seasonal tilts accounts for an annual costs between $760 and $848, but actual adjustments have historically not taken place according to the existing schedule. The analysis focuses on optimizing net energy …

Designing An Accessible Hall Effect Thruster, Matthew Baird

Honors Theses

A group of three Mechanical Engineering students have selected to design a 200 W Hall Effect Thruster to fulfill the Mechanical and Aeronautical Engineering senior design project. Preliminary studies were performed on the theory behind electric propulsion and plasma physics. The group designed the Western Hall Thruster and used COMSOL Multiphysics® simulation software to refine the magnetic circuit. The group then fabricated and performed magnetic testing of their thruster in Western Michigan University’s Aerospace Laboratory for Plasma Experiments. This testing will seek to prove that a standard research HET can be built by universities without substantial financial resources.

Human-Assisted Fluid Power Vehicle, Aaron Huntoon

Honors Theses

The rising cost of energy has prompted industrial and technology companies to research and implement renewable or green energy sources in every aspect of their business. This green technology can consist of sources such as: solar, wind, fluid, or others to create energy from renewable sources. The use of these various sources reduces the pollution associated with standard methods of energy development, and it will ultimately drive costs down to benefit the general population. One of the largest benefactors to the use of renewable energy sources is the transportation industry. Billions of people rely on various modes of transportation every …

Design Load Analysis Of Two Floating Offshore Wind Turbine Concepts, Gordon M. Stewart

Doctoral Dissertations

Much of the United States' wind resource is located over deep water where fixed-bottom offshore wind turbines are cost-prohibitive. To capture this energy, floating offshore wind turbines are being developed. However, current design standards do not explicitly cover issues relating to floating offshore wind turbines, which leads to risk and uncertainty in the design process. Two important issues that this dissertation investigates are the effect of simulation length and wind and wave misalignment on fatigue and ultimate loads. Experience in the offshore floating oil and gas industry has recommended simulation lengths of 3-6 hours, but the wind industry typically simulates …

Development Of A Model And Optimal Control Strategy For The Cal Poly Central Plant And Thermal Energy Storage System, Daniel Douglas Castro

Master's Theses

This thesis develops a calibrated model of the Cal Poly Central Chilled Water Plant with Thermal Energy Storage for use in determining an optimal operating control strategy. The model was developed using a transient systems simulation program (TRNSYS) that includes plant performance and manufacturer data for the primary system components, which are comprised of pumps, chillers, cooling towers, and a thermal energy storage tank. The model is calibrated to the actual measured performance of the plant using the current control strategy as a baseline. By observing and quantifying areas for potential improvement in plant performance under conditions of high campus …

Solar Thermal Collector, Hazel Tickner, Tyson Nakamura

All Undergraduate Projects

During the course of this project, a solar thermal collector and supporting stand were designed and manufactured to be used during Mechanical Engineering Technology labs. Students will be able to use the collector to heat water, with the sun being the only heat source. The collector was designed by calculating surface area limitations, estimated solar input, and desired efficiency, to find the required water flow rate. From there, the necessary pipe lengths and diameters were determined, and the solar thermal collector was constructed. Two pipe paths were manufactured: a curved path, and a manifold path. Students will be able to …