Mechanical Engineering Commons^™

Hydrogen Absorption In Weldments Of Overlaid Claded Pressure Vessel, Ronnie Higuchi Rusli

Makara Journal of Technology

Cracks was found in type 347 stainless steel internal attachment welds of a reactor for a high temperature, and high pressure hydrogen service. One of the possible causes of cracking is low cycle fatigue cracking induced by repetition of thermal stress to embrittled weld metal. Type 347 weld metal loses its ductility by presence of sigma phase and hydrogen.

The Decompositioning Of Volatile-Matter Of Tanjung Enim Coal By Using Thermogravimetry Analyzer (Tga), Nukman Nukman

Makara Journal of Technology

The Decompositioning of Volatile-Matter of Tanjung Enim Coal by using Thermogravimetry Analyzer (TGA). Coal is a nature material which a kind of energy source. The decompotition of coal could analyze by heat treated using thermogravimetry analyzer. The decomposition of the volatile matter for three kinds of Tanjung Enim coal could be known. The value of activation energy that be found diference, then for Semi Anthracite, Bitumonius and Sub Bituminous Coal, the initial temperatures are 60.8 oC, 70.7 oC, 97.8oC, and the last temperatures are 893.8 oC, 832 oC, 584.6oC.

Localised Galvanic Corrosion Processes In Thermal Spray Coated/Cast Aluminium Alloy Systems, David Culliton, Tony Betts, David Kennedy

Conference Papers

Cast Aluminium Alloys, because of the propensity of aluminium to react with impurities and alloying elements, are prone to developing IM impurities during the solidification process. These IM phases can act, in some fluids, as initiation sites for localised corrosion processes, resulting in degradation phenomena, such as pitting. Whilst Thermal Spray coatings can improve the wear resistance of Cast Aluminium Alloys, their corrosion performance may be hampered by the presence of through porosity within the coating.

The present work details some preliminary studies of the localised corrosion processes occurring at the interface area between a Thermal Spray coating and a …

A Plasma Model Combined With An Improved Two-Temperature Equation For Ultrafast Laser Ablation Of Dielectrics, Lan Jiang, Hai-Lung Tsai

Mechanical and Aerospace Engineering Faculty Research & Creative Works

It remains a big challenge to theoretically predict the material removal mechanism in femtosecond laser ablation. To bypass this unresolved problem, many calculations of femtosecond laser ablation of nonmetals have been based on the free electron density distribution without the actual consideration of the phase change mechanism. However, this widely used key assumption needs further theoretical and experimental confirmation. by combining the plasma model and improved two-temperature model developed by the authors, this study focuses on investigating ablation threshold fluence, depth, and shape during femtosecond laser ablation of dielectrics through nonthermal processes (the Coulomb explosion and electrostatic ablation). The predicted …

Three-Dimensional Modeling Of The Plasma Arc In Arc Welding, Gu Xu, J. Hu, Hai-Lung Tsai

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Most previous three-dimensional modeling on gas tungsten arc welding (GTAW) and gas metal arc welding (GMAW) focuses on the weld pool dynamics and assumes the two-dimensional axisymmetric Gaussian distributions for plasma arc pressure and heat flux. In this article, a three-dimensional plasma arc model is developed, and the distributions of velocity, pressure, temperature, current density, and magnetic field of the plasma arc are calculated by solving the conservation equations of mass, momentum, and energy, as well as part of the Maxwell's equations. This three-dimensional model can be used to study the nonaxisymmetric plasma arc caused by external perturbations such as …

Flush-Mounted Steady-Periodic Heated Film With Application To Shear-Stress Measurement, Kevin D. Cole

Department of Mechanical and Materials Engineering: Faculty Publications

Surface-mounted heated films have been used for fluid-flow measurement for many years. Recently unsteady heating of such surface films has been explored experimentally. In this paper steady-periodic heating of a surface-mounted film is studied analytically. Wall effects and axial heat conduction in the fluid are included. The temperature is found as an exact integral expression constructed from separate Green’s function formulations in the fluid flow and in the solid wall that are matched at the fluid-solid interface. Results for temperature, obtained by quadrature, are reported for several flow speeds and several steady-periodic frequencies. The results show that steady-periodic heating has …

Progress Toward Meeting The Challenges Of Our Coastal Urban Future, Juile Pullen, Jason Ching, David J. Sailor, William Thompson, Bob Bornstein, Darko Koracin

Mechanical and Materials Engineering Faculty Publications and Presentations

The article provides information on the Seventh Conference on Coastal Atmospheric and Oceanic Prediction and Processes, and the Seventh Symposium on the Urban Environment in San Diego, California on September 9-13, 2008. Topics include the heterogeneity of urban areas, coastal vulnerabilities, urban planning, and emergency response modeling. The conference featured several speakers including Walter Dabberdt and James Voogt.

Real-Time Vertical Track Deflection Measurement System, Sheng Lu

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Track quality is a major factor in railroad safety, and one accepted indicator of track quality is the vertical track deflection. Measuring track deflection from a moving railcar is difficult because there is no stable reference for the measurements. A system developed by researchers at the University of Nebraska to measure track deflection from a moving railcar in real-time is described in detail. The system consists of a loaded hopper with a camera/laser sensor system to detect the vertical deflection of the rail relative to the wheel/rail contact point. Modeling and simulation of the system is also presented along with …

Image Analyses Of Two Crustacean Exoskeletons And Implications Of The Exoskeletal Microstructure On The Mechanical Behavior, Liang Cheng, Liyun Wang, Anette M. Karlsson

Mechanical Engineering Faculty Publications

The microstructures of exoskeletons from Homarus americanus (American lobster) and Callinectes sapidus (Atlantic blue crab) were investigated to elucidate the mechanical behavior of such biological composites. Image analyses of the cross-sectioned exoskeletons showed that the two species each have three well-defined regions across the cuticle thickness where the two innermost regions (exocuticle and endocuticle) are load bearing. These regions consist of mineralized chitin fibers aligned in layers, where a gradual rotation of the fiber orientation of the layers results in repeating stacks. The exocuticle and endocuticle of the two species have similar morphology, but different thicknesses, number of layers, and …

Modeling And Simulation Of Hydrogen Generation From Hightemperature And Low-Temperature Water Gas Shift Reactions, Wei-Hsin Chen

Wei-Hsin Chen

No abstract provided.

Gtaw ايجادشده با روش جوشکاری Tini-Tic و Tini بررسی ريزساختاری پوشش, Masoud Harooni, Morteza Shamanian, Alireza Fadaei Tehrani

Masoud Harooni

هدف از انجام اين پژوهش بهبود سختي سطحي و ريزساختار فولاد ساده کربنی از نوع 52 و مقايسه ريز ساختار اين دو با هم GTAW ايجاد شده به روش جوشکاری TiNi-TiC و TiNi پوششی از بترتيب با نسبت استوکيومتری مساوي و نسبت ۲۰ Ti-Ni-C و Ti-Ni است. بدين منظور مخلوط پودری به طور جداگانه توسط روش فعال سازی مکانيکی فعال شد و سپس بر سطح TiC درصد تقويت کننده به ضخامت ۱ ميليمتر پيش نشانده شده با استفاده از روش جوشکاری قوسی St نمونه های فولادی 52 تنگستن- گاز ذوب و با فلز پايه امتزاج يافته است. جهت بررسي نوع …

Work In Progress - Enhancing Student-Learning Through State-Of-The-Art Systems Level Design And Implementation, Albert A. Liddicoat, Jianbiao Pan, James G. Harris, Dominic J. Dal Bello, Lynne A. Slivovsky

Industrial and Manufacturing Engineering

The curriculum for undergraduate engineering programs is often partitioned into several courses that are taught in isolation followed by a single culminating senior design or capstone project experience. In the senior design class students being to synthesize the knowledge and skills that they acquired through the engineering curriculum. This paper presents lower and upper division course and curricular changes made to accommodate learning objectives that better prepare students for project-based learning. These learning experiences and skills include: systems level design, experience with state-of-the-art Computer Aided Design (CAD) tools, printed circuit board (PBC) design, design for manufacturability, electronics assembly, project management, …

Overview And Summary Of Design Ideas From The High Performance Green Relocatable Classroom Charrette, Florida Solar Energy Center, Charles Withers, Jr.

FSEC Energy Research Center®

Past research has shown that energy use can be reduced by 81% in improved new portable classrooms in Florida. On June 2-3, 2008 a design charrette was held in Palm Beach Gardens with the goal of developing qualities that should be considered for a High-Performance Green Relocatable Classroom (HPGRC) standard for Florida or other regions in hot and humid climates. This charrette is just one of many steps that would be involved in development and acceptance of a HPGRC standard. It is hoped that the results of this can be shared with others and used to build on the development …

Impact Assessment Of Problem-Based Learning In An Engineering Science Course, Karim J. Nasr, Bassem Ramadan

Mechanical Engineering Publications

This paper presents the development and implementation of Problem-Based Learning (PBL) in an engineering thermodynamics course at Kettering University. In this project, the thermodynamics course was restructured as modules presenting practical applications first, whereas principles were introduced just-in-time and as encountered. Theoretical information was presented to support the understanding of knowledge as students applied inquiry-based learning. These modules were carefully designed to reflect traditional concepts but made more exciting as students discover the need for the laws and principles. The classroom format was interactive, cooperative and revolves around students' needs. Formative and summative assessment tools were designed to examine the …

Contact-Resonance Atomic Force Microscopy For Viscoelasticity, P. A. Yuya, D. C. Hurley, Joseph A. Turner

Department of Engineering Mechanics: Faculty Publications

We present a quantitative method for determining the viscoelastic properties of materials with nanometer spatial resolution. The approach is based on the atomic force acoustic microscopy technique that involves the resonant frequencies of the atomic force microscopy cantilever when its tip is in contact with a sample surface. We derive expressions for the viscoelastic properties of the sample in terms of the cantilever frequency response and damping loss. We demonstrate the approach by obtaining experimental values for the storage and loss moduli of a poly(methyl methacrylate) film using a polystyrene sample as a reference material. Experimental techniques and system calibration …

A Mechanistic Investigation Of Nitrogen Evolution In Pulverized Coal Oxy-Fuel Combustion, Andrew John Mackrory

Theses and Dissertations

Oxy-fuel combustion is an enabling technology for capture of CO2 from coal combustion, the economics of which depends strongly on the ability of the process to produce low NOX emissions. The literature contains many reports of lower NOX emissions from oxy-fuel combustion but the reasons for this are not fully understood. The objective of this work was to gain understanding of nitrogen evolution under pulverized coal oxy-fuel conditions. Pulverized coal was burned in a once-through, down-fired, laminar flow reactor. Nitrogen compounds and other combustion species were measured at the reactor centerline as a function of distance from the burner. Dry …

Homogeneous Dbd In N2: 1) Lif, Talif And Electrical Measurements, N. Gherardi, Et. Es-Sebbar, C. Sarra-Bourret, N. Naudé, F. Massines

Dr. Et-touhami Es-sebbar

In this paper we compare two different discharges that can be obtained in a DBD configuration, that is to say the filamentary discharge (usual regime in atmospheric DBD) with the Atmospheric Pressure Townsend Discharge (APTD), which is a homogeneous regime obtained in nitrogen atmosphere. The aim is to help in the understanding of the processes which control the transition from one regime to the other. To do so, the discharge is characterized through electrical measurements, coupled with optical diagnostics among which Laser Induced Fluorescence (LIF) for radical density measurements. The influence of the addition of small quantities of additives on …

Rheological Study Of Polymer Flow Past Rough Surfaces With Slip Boundary Conditions, Anoosheh Niavarani, Nikolai V. Priezjev

Mechanical and Materials Engineering Faculty Publications

The slip phenomena in thin polymer films confined by either flat or periodically corrugated surfaces are investigated by molecular dynamics and continuum simulations. For atomically flat surfaces and weak wall-fluid interactions, the shear rate dependence of the slip length has a distinct local minimum which is followed by a rapid increase at higher shear rates. For corrugated surfaces with wavelength larger than the radius of gyration of polymer chains, the effective slip length decays monotonically with increasing corrugation amplitude. At small amplitudes, this decay is reproduced accurately by the numerical solution of the Stokes equation with constant and rate-dependent local …

Alternative Binder Carbide Tools For Machining Superalloys, Daniel J. Waldorf, Michael Stender, Scott Liu, Daniel Norgan

Industrial and Manufacturing Engineering

This study examines the performance of a new class of wear-resistant but economical cutting tools produced by varying the binder composition of standard cemented carbide composites. By replacing some or all of the cobalt binder with rhenium and nickel-based superalloy, a stronger composite tool results, potentially capable of machining heat-resistant superalloys at significantly higher cutting speeds. Sample tools with alternative binder were produced and compared to standard tools bound with cobalt only. Turning experiments on Inconel 718 were run to evaluate wear resistance and tool life for several grades. The experimentation also examined the effects of varying the relative proportions …

Newsletters For The Larsen Tractor Museum, Tractor Museum

Lester F. Larsen Tractor Museum: Planning and Development Documents

No abstract provided.

Design And Analysis Of A Positively Engaged Continuously Variable Transmission, Brandon Levi Haupt

Theses and Dissertations

With energy demands at an all time high, mechanical power systems are under great scrutiny. Substantial efforts are being made throughout the world to reduce energy use in common mechanical systems such as the internal combustion engine and transmission system. Eliminating or reducing efficiency losses in the transmission is a potential source of improving the efficiency of the system. To do so, various alternative types of transmissions are being investigated. At Brigham Young University, development of a Positively Engaged Continuously Variable Transmission (PECVT) is progressing. In addition to the efficiency increases that would occur as a result of operating the …

Impact Mechanics And High-Energy Absorbing Materials: Review, Pizhong Qiao, Mijia Yang, Florin Bobaru

Department of Engineering Mechanics: Faculty Publications

In this paper a review of impact mechanics and high-energy absorbing materials is presented. We review different theoretical models (rigid-body dynamics, elastic, shock, and plastic wave propagation, and nonclassical or nonlocal models. and computational methods (finite-element, finite-difference, and mesh-free methods. used in impact mechanics. Some recent developments in numerical simulation of impact (e.g., peridynamics) and new design concepts proposed as high energy absorbing materials (lattice and truss structures, hybrid sandwich composites, metal foams, magnetorheological fluids, porous shape memory alloys. are discussed. Recent studies on experimental evaluation and constitutive modeling of strain rate-dependent polymer matrix composites are also presented. Impact damage …

Numerical Simulation Of Thermo-Elasticity, Inelasticity And Rupture Inmembrane Theory, Michael Taylor

Mechanical Engineering

Two distinct two-dimensional theories for the modeling of thin elastic bodies are developed. These are demonstrated through numerical simulation of various types of membrane deformation. The work includes a continuum thermomechanics-based theory for wrinkled thin films. The theory takes into account single-layer sheets as well as composite membranes made of multiple lamina. The resulting model is applied to the study of entropic elastic elastomers as well as Mylar/aluminum composite films. The latter has direct application in the area of solar sails. Several equilibrium deformations are illustrated numerically by applying the theory of dynamic relaxation to a finite difference discretization based …

Hardware Dispenser Project, John D. Raff, Dave Owen, Paul Sheppard

Service-Learning Program

The purpose of this design project was to develop a system that will allow employees of the ARC to be able to work on a greater variety of projects and to improve their productivity. The hardware dispenser group developed a design for a tray that would help the ARC employees work quicker and more efficiently. The tray has bins to hold hardware which the supervisor loads onto the tray. The employee slides a bag over the tip of the funnel and into the clip which holds the bag in place. The worker then chooses which parts need to be in …

European Climate Policy And The Position Of Cyprus, Theodoros Zachariadis

Theodoros Zachariadis

No abstract provided.

Thermal Stability Of Electrodeposited Liga Ni-W Alloys For High Temperature Mems Applications, Haseeb Asma

Haseeb ASMA

For thermally stable LIGA materials for high temperature MEMS applications LIGA Ni-W layers and micro testing samples with different compositions (15 and 5 at% W) were electrodeposited. In order to investigate the thermal stability the Ni-W layers were annealed at different temperatures (300-700 degrees C) and for different durations (1, 4, 16 h). Their microstructure and micro-hardness were than analysed after annealing and compared with those of as-deposited states. The observed microstructures show, in comparison to pure LIGA nickel, a small grain growth and a relatively stable structure up to 700 degrees C. The micro-hardness values of the LIGA Ni-W …

Ole Miss Engineer 2008

Ole Miss Engineer

No abstract provided.

High Bandwidth Control Of Precision Motion Instrumentation, Douglas A. Bristow, Jingyan Dong, Andrew G. Alleyne, Srinivasa M. Salapaka, Placid M. Ferreira

Mechanical and Aerospace Engineering Faculty Research & Creative Works

This article presents a high-bandwidth control design suitable for precision motion instrumentation. Iterative learning control (ILC), a feedforward technique that uses previous iterations of the desired trajectory, is used to leverage the repetition that occurs in many tasks, such as raster scanning in microscopy. Two ILC designs are presented. The first design uses the motion system dynamic model to maximize bandwidth. The second design uses a time-varying bandwidth that is particularly useful for nonsmooth trajectories such as raster scanning. Both designs are applied to a multiaxis piezoelectric-actuated flexure system and evaluated on a nonsmooth trajectory. The ILC designs demonstrate significant …

Adaptive Control Of Freeze-Form Extrusion Fabrication Processes, Xiyue Zhao, Robert G. Landers, Ming-Chuan Leu

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Freeze-form Extrusion Fabrication (FEF) is an additive manufacturing process that extrudes high solids loading aqueous ceramic pastes in a layer-by-layer fashion below the paste freezing temperature for component fabrication. Due to effects such as the air bubble release, agglomerate breakdown, change in paste properties during extrusion as a result of liquid phase migration, etc., the extrusion force is difficult to control. In this paper, an adaptive controller is proposed to regulate the extrusion force. Recursive Least Squares is used to estimate extrusion force model parameters during fabrication and a low-order control scheme capable of tracking general reference trajectories is designed …

Parameter Estimation Of The Arterial System, James Charles Carter Ii

Mechanical & Aerospace Engineering Theses & Dissertations

There are a number of disorders that originate from or involve faulty operation of the cardiovascular system. Diseases such as atherosclerosis, diabetes and hypertension can have a debilitating effect on blood flow. This makes the tools for simulating the effects of such diseases on blood flow important. Measures, such as pulse wave velocity, that are generated by models of the cardiovascular system can be important indicators of cardiac health. Although physically measurable, obtaining some parameters comes with a high cost and discomfort to the patient. Models can provide an assessment of many important parameters. The purpose of this project was …