Mechanical Engineering Commons^™

Modeling, Fabrication, And Optimization Of Niobium Cavities Phase Iii: Quarterly Report, Robert A. Schill Jr., Mohamed Trabia

Transmutation Sciences Materials (TRP)

This quarterly report provides an update to the last phase of the Modeling, Fabrication, and Optimization of Niobium Cavities. Designing the experimental setup of secondary electron emission was well underway in early summer of 2003 when funding was made available for this portion the study. By March 2004, many of the components of the experimental study reached UNLV with some assembly accomplished. The first secondary electron emission (SEE) measurement was made from the surface of a Faraday cup in September 2004. At a particular beam energy, the current measured with the Faraday cup and electrometer changed sign over a range …

Unmanned Air Vehicle Testbed For Cooperative Control Experiments, Timothy W. Mclain, Randal W. Beard

Faculty Publications

This paper describes the MAGICC Lab unmanned air vehicle (UAV) testbed at Brigham Young University. Motivation for pursuing experimental research with UAVs is given as well as a historical perspective of the UAV testbed development. Lessons learned through the development and use of the testbed over the past several years are summarized.

Project-Based Introduction To Engineering - A University Core Course, Samuel Bogan Daniels, Bouzid Aliane, Jean Nocito-Gobel, Michael Collura

Engineering and Applied Science Education Faculty Publications

This paper describes a first year engineering course that is taken by both engineering and non-engineering students. The project-based Introduction to Engineering course, EAS107P, fulfills a university core curriculum elective. Although engineering students take the course during their first year, students from other majors typically elect to take the course later in their curriculum. The focus of EAS107P is to have students experience the engineering design and problem solving process in a multi-disciplinary, team-based setting. In addition to learning about design, students develop an interest in the engineering profession and build a foundation of skills for future work. An additional …

Development Of A Multidisciplinary Engineering Foundation Spiral, Samuel Bogan Daniels, Bouzid Aliane, Jean Nocito-Gobel, Michael Collura

Engineering and Applied Science Education Faculty Publications

To operate effectively in today’s workforce engineers need to have a muti-disciplinary perspective along with substantial disciplinary depth. This broad perspective cannot be achieved by merely taking 2 or 3 engineering courses outside of the major, but rather will require a radical change in the way we educate engineers. The faculty of the School of Engineering and Applied Science at the University of New Haven have developed a new approach: the Multidisciplinary Engineering Foundation Spiral. This curricular model provides the needed mix of breadth and depth, along with the desired professional skills, by providing carefully crafted, well-coordinated curricular experiences in …

Project-Based Introduction To Engineering -- Course Assessment, Samuel Bogan Daniels, Michael Collura, Bouzid Aliane, Jean Nocito-Gobel

Engineering and Applied Science Education Faculty Publications

The School of Engineering and Applied Science at the University of New Haven has a newly developed project-based Introduction to Engineering course. This new course plays a central role in the new Multi-Disciplinary Engineering Foundation Spiral curriculum as the first semester course for all engineering freshmen. An assessment process was developed to determine the effectiveness of this project-based course, specifically with attention towards assessing attitudes, impact on retention, problem-solving and engineering foundation topics. This paper addresses the particular portion of the assessment process for the individual course projects and their contribution to the last two assessment categories.

Project Planning & Development For Engineering Freshmen, Bouzid Aliane, Michael Collura, Samuel Bogan Daniels, Jean Nocito-Gobel

Engineering and Applied Science Education Faculty Publications

The nature and background of students seeking an engineering education has changed drastically in the last decade, as has the expectations of industrial employers. Many students lack the organizational skills needed for academic success. Similar organizational skills, although more advanced, are required for managing engineering projects. A new course was developed by the faculty at the School of Engineering and Applied Science at the University of New Haven. Through this course, a key component of the Multidisciplinary Engineering Foundation Spiral, seeks to promote higher retention rates, increase student motivation and begin a confidence-building transition to professional practice. Project management concepts …

Modeling, Fabrication, And Optimization Of Niobium Cavities: Phase Iii Third Quarterly Report, Robert A. Schill Jr., Mohamed Trabia

Transmutation Sciences Materials (TRP)

Niobium cavities are important parts of the integrated NC/SC high-power linacs. Over the years, researchers in several countries have tested various cavity shapes. They concluded that elliptically shaped cells are the most appropriate shape for superconducting cavities. The need for very clean surfaces lead to the use of a buffered chemical polishing produce for surface cleaning to get good performance of the cavities. The third phase concludes the experimental a fluid flow study and optimization study. The first quarter and second quarter of phase three also begins the experimental set-up of secondary emission studies from niobium in superconducting mode. This …

Modeling, Fabrication, And Optimization Of Niobium Cavities: Phase Iii Second Quarterly Report, Robert A. Schill Jr., Mohamed Trabia

Transmutation Sciences Materials (TRP)

Niobium cavities are important parts of the integrated NC/SC high-power linacs. Over the years, researchers in several countries have tested various cavity shapes. They concluded that elliptically shaped cells are the most appropriate shape for superconducting cavities. The need for very clean surfaces lead to the use of a buffered chemical polishing produce for surface cleaning to get good performance of the cavities. The third phase concludes the experimental a fluid flow study and optimization study. The first quarter and second quarter of phase three also begins the experimental set-up of secondary emission studies from niobium in superconducting mode. This …

Modeling, Fabrication, And Optimization Of Niobium Cavities, Robert A. Schill Jr., Mohamed Trabia, William Culbreth

Transmutation Sciences Materials (TRP)

One of the key technologies for the deployment of acceleratordriven transmutation systems is the accelerator itself. Elliptical superconducting niobium cavities are used to increase the efficiency of the high-power accelerators needed to support the transmutation mission.

One of the major sources of energy loss from a superconducting accelerator cavity is a process known as multiple impacting (or “multipacting”) of electrons. This phenomenon limits the maximum amount of energy and power that the niobium cavity can store. As a result, the maximum power available for accelerating the desired charge, as well as the overall performance of the accelerator is reduced. Furthermore, …

The Frequency Distribution Of Quantization Error In Digitizers For Coherent Sampling, Sol Neeman Ph.D.

Engineering Studies Faculty Publications and Creative Works

In this paper the frequency distribution of quantization error in coherent sampling of digitizers will be investigated. As the distribution of the quantization error affects the values of THD and SNR, it is relevant for a correct interpretation of THD and SNR of sine waves in coherent sampling. The distribution of the quantization error will be analyzed as a function of N, total number of samples and M, number of cycles in the sample set and it will be proved that for certain cases, the quantization error falls on odd harmonics only of the frequency of the sampled sine wave.

Design And Technologies For A Smart Composite Bridge, K. Chandrashekhara, Prakash Kumar, Steve Eugene Watkins, Antonio Nanni

Mechanical and Aerospace Engineering Faculty Research & Creative Works

An all-composite, smart bridge design for shortspan applications is described. The bridge dimensions are 9.14-m (30-ft.) long and 2.74-m (9-ft.) wide. A modular construction based on assemblies of pultruded fiber-reinforced-polymer (FRP) composite tubes is used to meet American Association of State Highway and Transportation Officials (AASHTO) H20 highway load ratings. The hollow tubes are 76 mm (3 in.) square and are made of carbon/vinyl-ester and glass/vinyl-ester. An extensive experimental study was carried out to obtain and compare properties (stiffness, strength, and failure modes) for a quarter portion of the full-sized bridge. The bridge response was measured for design loading, two-million-cycle …