Open Access. Powered by Scholars. Published by Universities.®
- Keyword
-
- 3D airfoil (1)
- Biomechanics Simulation; OpenSim; Flexion/Extension; Exoskeleton; "Push-pull" (1)
- Control theory (1)
- Coupled mode (1)
- Dynamic stall (1)
-
- Experiment (1)
- FSI (1)
- Federer's coarea formula (1)
- Flow (1)
- Fluid (1)
- Flutter (1)
- Generator torque (1)
- Hip Exoskeleton (1)
- Impedance control (1)
- Individual flap control (1)
- Individual pitch control (1)
- Isosurface Area (1)
- ONERA (1)
- Scotch yoke (1)
- Series elastic actution (1)
- Smart rotors (1)
- Surface Area (1)
- Third order non-linear (1)
- Trailing edge flap (1)
- Turbulent flows (1)
- VIV (1)
- Vortex (1)
- Wind energy (1)
Articles 1 - 6 of 6
Full-Text Articles in Mechanical Engineering
Calculation Of Scalar Isosurface Area And Applications, Kedar Prashant Shete
Calculation Of Scalar Isosurface Area And Applications, Kedar Prashant Shete
Masters Theses
The problem of calculating iso-surface statistics in turbulent flows is interesting for a number of reasons, some of them being combustion modeling, entrainment through turbulent/non-turbulent interfaces, calculating mass flux through iso-scalar surfaces and mapping of scalar fields. A fundamental effect of fuid turbulence is to wrinkle scalar iso-surfaces. A review of the literature shows that iso-surface calculations have primarily been done with geometric methods, which have challenges when used to calculate surfaces that have high complexity, such as in turbulent flows. In this thesis, we propose an alternative integral method and test it against analytical solutions. We present a parallelized …
A Numerical Flutter Predictor For 3d Airfoils Using The Onera Dynamic Stall Model, Pieter Boersma
A Numerical Flutter Predictor For 3d Airfoils Using The Onera Dynamic Stall Model, Pieter Boersma
Masters Theses
To be able to harness more power from the wind, wind turbine blades are getting longer. As they get longer, they get more flexible. This creates issues that have until recently not been of concern. Long flexible wind turbine blades can lose their stability to flow induced instabilities such as coupled-mode flutter. This type of flutter occurs when increasing wind speed causes a coupling of a bending and a torsional mode, which create limit cycle oscillations that can lead to blade failure. To be able to make the design of larger blades possible, it is important to be able to …
Streamwise Flow-Induced Oscillations Of Bluff Bodies - The Influence Of Symmetry Breaking, Tyler Gurian
Streamwise Flow-Induced Oscillations Of Bluff Bodies - The Influence Of Symmetry Breaking, Tyler Gurian
Masters Theses
The influence of symmetry breaking on the flow induced oscillations of bluff bodies in the steamwise direction is studied. First, a series of experiments is conducted on a one-degree-of-freedom circular cylinder allowed to exhibit pure translational motion in the streamwise direction over a range of reduced velocities, 1.4 < U* < 4.4, corresponding to a Reynolds number range of 970 < Re < 3370. Two distinct regions of displacements were observed in reduced velocity ranges of 1.6 < U* < 2.5 and 2.75 < U* < 3.85. Measured force coefficients in the drag and lift direction were examined, along with the wake visualization, through the range of reduced velocities, to infer the resulting wake modes. A new Alternating Symmetric (AS) mode was found. This transition from symmetric to AS shedding occurred near the end of the first region of response. Similar tests were run with a square prism in the parameter space of 2.4 < U* < 5.8 and 757 < Re < 1900 over angles of incidence of 0° ≤ α ≤ 45°. A distinct region of lock-in is observed for α = 0°, 2.5°, 5°, 7.5° over 3.2 < U* < 5.4 for α = 0°, and decreasing with increasing α. The wake structures were found to be roughly symmetric for α = 0°, but transitioned towards asymmetry …
Evaluation Of Impedance Control On A Powered Hip Exoskeleton, Punith Condoor
Evaluation Of Impedance Control On A Powered Hip Exoskeleton, Punith Condoor
Masters Theses
This thesis presents an impedance control strategy for a novel powered hip exoskeleton designed to provide partial assistance and leverage the dynamics of human gait. The control strategy is based on impedance control and provides the user assistance as needed which is determined by the user’s interaction with the exoskeleton. A series elastic element is used to drive the exoskeleton and measures the interaction torque between the user and the device. The device operates in two modes. Free mode is a low impedance state that attempts to provide no assistance. Assist mode increases the gains of the controller to provide …
Design Of A Passive Exoskeleton Spine, Haohan Zhang
Design Of A Passive Exoskeleton Spine, Haohan Zhang
Masters Theses
In this thesis, a passive exoskeleton spine was designed and evaluated by a series of biomechanics simulations. The design objectives were to reduce the human operator’s back muscle efforts and the intervertebral reaction torques during a full range sagittal plane spine flexion/extension. The biomechanics simulations were performed using the OpenSim modeling environment. To manipulate the simulations, a full body musculoskeletal model was created based on the OpenSim gait2354 and “lumbar spine” models. To support flexion and extension of the torso a “push-pull” strategy was proposed by applying external pushing and pulling forces on different locations on the torso. The external …
New Generator Control Algorithms For Smart-Bladed Wind Turbines To Improve Power Capture In Below Rated Conditions, Bryce B. Aquino
New Generator Control Algorithms For Smart-Bladed Wind Turbines To Improve Power Capture In Below Rated Conditions, Bryce B. Aquino
Masters Theses
With wind turbines growing in size, operation and maintenance has become a more important area of research with the goal of making wind energy more profitable. Wind turbine blades are subjected to intense fluctuating loads that can cause significant damage over time. The need for advanced methods of alleviating blade loads to extend the lifespan of wind turbines has become more important as worldwide initiatives have called for a push in renewable energy. An area of research whose goal is to reduce the fatigue damage is smart rotor control. Smart bladed wind turbines have the ability to sense aerodynamic loads …