Mechanical Engineering Commons^™

Modeling, Optimizing And Testing Thermoelectric Generators For Liquid-To-Liquid Low Grade Waste Heat Recovery, Ali Eyddan Hamil

Masters Theses

The use of thermoelectric generators (TEGs) for producing electricity from low grade waste heat is thought to be a great solution in the future to reduce the power generation cost because of their advantages of reliability and environmental friendliness. Therefore, the current project aims to study thermoelectric generators for low grade waste heat recovery. In this work, a single unit cell of liquid to liquid thermoelectric generator attached with heat exchangers (heat sinks) is modeled using an internal flow. Its optimum design is obtained based on heat sink optimization and the optimal design method. An analytical model of four unit …

Experimental Characterization And Simulation Of Carbon Nanotube Strain Sensing Films, Nagendra Krishna Chaitanya Tummalapalli

Masters Theses

Carbon Nanotubes (CNTs) have excellent mechanical, electrical and electromechanical properties. These properties led to a lot of novel applications. Due to change in electrical properties under mechanical loading, these composites have potential applications in strain sensors, when these are fabricated as films. CNT-based films are commonly fabricated using different physical and chemical techniques based on the property requirements governing those applications. In this work, CNT films were prepared using wet chemical based methods and chemical vapor deposition techniques.

Plasma chemical vapor deposition using microwave power is used in the first method to deposit films on silicon substrates, using Nickel film …

Analytical Study Of Miniature Thermoelectric Device, Mohammed Dhannoon

Masters Theses

Miniature thermoelectric devices (TE) have been regarded as hopeful devices to attain efficient cooling in microprocessors and other small-scale devices. To recognize the performances of miniature thermoelectric coolers, a thermoelectric cooling module is theoretically analyzed. Particular attention is paid to the impact of the thermoelectric element length effect and the substrate material type influence on the cooling performance. The electrical contact resistance and thermal contact are taken into account.

Furthermore, miniature thermoelectric is compared with large thermoelectric, and effective material properties of miniature thermoelectric are studied. The obtained results also demonstrate power density (cooling/heating power per unit area of the …

Development Of An Analytical Model For Beams With Two Dimples In Opposing Directions, Mofareh H. Ghazwani

Masters Theses

Structures such as beams and steel plates can produce potentially high levels of unwanted vibrations and noises in the environment. A method of improving the vibration and acoustic characteristics of beams based on introducing dimples on its surfaces will be presented in this study. This method focuses on creating two dimples in the same and opposite direction on beam’s surface where the effect of dimples on the change in beam’s natural frequencies is the problems of interest.

A boundary value model (BVM) is developed for a beam with two dimples and subjected to various boundary conditions using Hamilton’s Variational Principle. …

Optimal Design Of Automotive Exhaust Thermoelectric Generator (Aeteg), Hassan Fagehi

Masters Theses

A consumption of energy continues to increase at an exponential rate, especially in terms of automotive spark ignitions vehicles. About 40% of the applied fuel into a vehicle is lost as waste exhaust to the environment. The desire for improved fuel efficiency by recovering the exhaust waste heat in automobiles has become an important subject. The thermoelectric generator (TEG) has the potential to convert exhaust waste heat into electricity as long as it is improving fuel economy. The remarkable amount of research being conducted on TEGs indicates that this technology will have a bright future in terms of power generation. …

Analytical Modeling And Numerical Simulation Of A Thermoelectric Generator Including Contact Resistances, Shripad Dhoopagunta

Masters Theses

With increasing demand for energy harvesting systems, research has been conducted in different areas in which Thermoelectric Generators (TEG) find their way into the top of many available resources. Out of many energy harvesting systems available, TEGs are comparatively easier to study, to manufacture and also to comprehend while producing enough energy for applications they find use in. They are solid state devices, meaning; they do not have any moving parts and hence makes them durable. Most of the energy that goes out of the automobile as exhaust is reused to power the TEGs. In most of the works that’s …

Optimization Methodology For Cvt Ratio Scheduling With Consideration Of Both Engine And Cvt Efficiency, Steven Beuerle

Masters Theses

A transmission ratio schedule is developed to optimize the fuel consumption for an automotive continuously variable transmission (CVT) connected to an internal combustion engine (ICE). Although the optimal operating line (OOL) generated from an engine brake specific fuel consumption (BSFC) map can be used to generate a CVT ratio schedule that yields maximum engine efficiency, it was found that OOL-based CVT ratio scheduling does not necessarily offer the best fuel economy because optimal CVT efficiency does not always correspond to OOL tracking. To develop a CVT ratio schedule that can offer the best fuel economy, a novel ratio-scheduling methodology is …

A Genetic Algorithm Incorporating Design Choice For The Preliminary Design Of Unmanned Aerial Vehicles, Kenneth Michael Mull

Masters Theses

Unmanned Aerial Vehicles (UAVs) are currently at the forefront of aerospace technologies. The design of these aircraft is complex and often performance characteristics are coupled to multiple design attributes. At the early design phase both discrete and continuous design choices are present limiting the feasibility of traditional derivative based optimization techniques. In place of these methods, the design space can be explored using a genetic algorithm that mimics the process of natural selection, providing a capable and reliable base airframe constructed from the required performance metrics. By incorporating a genetic multidisciplinary optimization algorithm early in the conceptual design phase, aircraft …

Dynamic Monitoring And Life Prediction Of Internal Strain-Gage Balances, David Leon Yoder

Masters Theses

Wind tunnel test customers continue to push the limits by producing air vehicle designs that produce high aerodynamic loads at the desired test conditions. These loads are a combination of steady aerodynamic, unsteady aerodynamic, and inertial forces. A methodology to monitor the health of a wind tunnel strain-gage balance has been developed. The objective of this methodology is to define the stress limits of the balance and monitor these limits so the balance can be safely tested without failure of the balance. A balance failure could result in costly damage to the wind tunnel model, support system, and the wind …

Development, Analysis, And Optimization Of A Swirl-Promoting Mean Flow Solution For Solid Rocket Motors, Andrew Steven Fist

Masters Theses

This work demonstrates and analyses a new flow candidate for describing the internal gaseous motion in simulated rocket motors. The fundamental features of this solution include the conservation of key system properties also incorporated in the classic Taylor-Culick (TC) system (i.e. inviscid, axisymmetric, steady and rotational properties), while allowing for the development of a swirling velocity component. The work compares the new solution to the development and formulation of the classic TC system, ultimately identifying that both the new and classic solutions are special cases of the Bragg-Hawthorne equation. Following this development, the text then explores the development of energy-optimized …

Improved Modeling Of Atmospheric Entry For Meteors With Nose Radii Between 5cm And 10m, Jakob Dale Brisby

Masters Theses

Atmospheric entry studies typically look closely at the peak heating rate that a body encounters during its trajectory. This is an extremely important phenomenon to study because it allows engineers to determine if a trajectory is possible with given materials and craft design specifications. It also allows designers to choose what type of method will be used for mitigating the enormous heat fluxes during entry. In general, it is accepted that during the super-sonic flight regime the body will continue to be heated and an ablative heat shield often is used to deal with these heating processes. The theory outlined …

The Decomposition Of Hydroxylammonium Nitrate Under Vacuum Conditions, Gregory A. Neff

Masters Theses

This research investigates the decomposition of the ionic liquid: hydroxylammonium nitrate (HAN), under vacuum conditions. All research was conducted at the Aerospace Laboratory for Plasma Experiments (ALPE) at Western Michigan University. Hydroxylammonium nitrate solution 24% wt. in H2O was used consistently throughout this research. A variety of temperatures and pressures ranging from 23°C to 645°C and 6E-3 Torr to 4 Torr, respectively, were used to decompose HAN. The primary gaseous species resulting from these decomposition conditions are N2O, NO, and trace amounts of NO2. The formation of H2O, and N2 is conditional on the experimental conditions, and the formation of …

A Linear Matrix Inequality-Based Approach For The Computation Of Actuator Bandwidth Limits In Adaptive Control, Daniel Robert Wagner

Masters Theses

"Linear matrix inequalities and convex optimization techniques have become popular tools to solve nontrivial problems in the field of adaptive control. Specifically, the stability of adaptive control laws in the presence of actuator dynamics remains as an important open control problem. In this thesis, we present a linear matrix inequalities-based hedging approach and evaluate it for model reference adaptive control of an uncertain dynamical system in the presence of actuator dynamics. The ideal reference dynamics are modified such that the hedging approach allows the correct adaptation without being hindered by the presence of actuator dynamics. The hedging approach is first …