Mechanical Engineering Commons^™

Numerical Analysis Of A Multi-Stage Elastohydrodynamic Seal For Aircraft Engines, Md Wasif Hasan

Electronic Theses and Dissertations

At present, both governmental and private aviation enterprises are trying to develop aircraft that are swifter, more lightweight, and more cost-effective in order to maintain competitiveness on both the domestic and global stage. Continuous innovation and sustainability efforts are necessary to achieve advancements in aviation systems, such as fans, compressors, combustors, and turbines, as well as sub-systems, like engine seals. Advanced engine seals exhibit considerable potential in enhancing the engine's pressure ratio and cycle temperatures, leading to reduced engine weight, increased thrust, and improved fuel economy. In this study, a novel multistage seal idea has been proposed for the supercritical …

Drop Impact On Dry And Liquid Infused Substrates With Micro-Wells., Ahmed Nazrul Islam

Electronic Theses and Dissertations

Drop impact on different types of surfaces are important physical concepts that are routinely found in day-to-day life and such studies have immense application for various types of industries. One such important application of drop dynamics is in the field of aviation science which is concerned of very large freezing drizzle drops impacting on airplane wings. Such drops are known as supercooled large droplets (SLD), and they pose a great risk and have been long known to have caused notable accidents in the past. SLDs are liquid drops that can remain in the state of liquid phase and grow into …

A Non-Reacting Passive Scalar Comparison Of Starccm And Openfoam In A Supersonic Cavity Flame Holder, Thomas Nuese

Electronic Theses and Dissertations

The scramjet engine equipped with a modern-day airliner would allow for very quick travel across the United States. The major problem is that designing such an engine and testing it to make sure it is safe would cost millions if not billions of dollars. Computational fluid dynamics allows for complex designs to be tested but can still take many days, weeks, or even months to complete. With the use of computational fluid dynamics (CFD), the scramjet engine can be analyzed to determine a quicker way to test and develop a reliable configuration in addition to analyzing the effects of different …

A Computational Fluid Dynamics Analysis Of The Temperature And Impurity Profiles In The Protodune-Sp Neutrino Detector, Jenna Harrison

Electronic Theses and Dissertations

Computational fluid dynamics (CFD) models of the ProtoDUNE single-phase detector were developed, refined, and analyzed. The ProtoDUNE single-phase detector is a prototype detector that is part of the Deep Underground Neutrino Experiment, an international research collaboration aimed at better understanding neutrinos and the role they play in our universe. The ProtoDUNE single-phase detector is used to gather data and inform design changes for the full-sized far detector prior to its construction. The effects of certain geometric features and heat sources on the thermal profiles within the liquid region of the detector were investigated in a set of parametric studies. The …

Cfd And Heat Transfer Analysis Of Rocket Cooling Techniques On An Aerospike Nozzle, Geoffrey Sullivan

Electronic Theses and Dissertations

In recent years the development of rocket engines has been mainly focused on improving the engine cycle and creating new fuels. Rocket nozzle design has not been changed since the late 1960s. Recent needs for reliable and reusable rockets, as well as advancements in additive manufacturing, have brought new interest into the aerospike nozzle concept. This nozzle is a type of altitude adjusting nozzle that is up to 90% more efficient than bell nozzles at low altitudes and spends up to 30% less fuel. Since the nozzle body is submerged in the hot exhaust gasses it is difficult to keep …

Design Of A 300cm2 Pemfc Stack With Force And Cfd Simulation To Optimize Flow Channels, Gasket Design, And Clamping Forces., Robert M. Ench

Electronic Theses and Dissertations

Proton exchange membrane fuel cells are important to the future of green energy as hydrogen can be made with green technologies and store energy for later use. Fuel cells can efficiently convert the hydrogen to electricity as needed. This study uses Solidworks simulation to make design improvements to the fuel cell before the prototype build stage of testing; this saves money and time by reducing the prototype builds needed.

In this study, a multi-channel serpentine design with two outlets versus a single outlet is evaluated using CFD to investigate pressure drop. Lower pressure drops are desirable as less energy input …

Quantification Of Velocity At The Sparkplug In A Lab Scale Combustion Chamber, Mayur Panduranga Kodikal

Electronic Theses and Dissertations

Lean burn has been considered an effective strategy to improve the thermal efficiency of spark-ignition engines. Under lean or diluted conditions, however, the combustion speed is reduced. Therefore, to speed up the combustion, in-cylinder turbulence is induced which may impede the spark initiation. This research aims to quantify the turbulence in a constant volume optical combustion chamber.

An Improved Delayed Detached Eddy Simulation (IDDES) study was done to understand the turbulence characteristics of the flow in the optical chamber. Spark anemometry was used to obtain a relationship between the spark plasma evolution and freestream velocity. Finally, this technique has been …

Particle Injection Simulation On Cold Spray Technology, Christopher A. Santini

Electronic Theses and Dissertations

Computational Fluid Dynamics (CFD) is a useful tool when it comes to research in the fields of Aerodynamics, Turbomachinery, and is used in several other fields of research. CFD is an important tool in the engineering industry because it allows for understanding and evaluation of a new design, this can lead to advancements in developing a more efficient and effective design. This tool helps in the understanding of the flow phenomena and how it can interact with its surroundings. One of the main reasons in the use of CFD is to reduce the cost of testing a design by running …

A Numerical And Experimental Study On Effect Of Composition Of Ar-N2 Shielding Gas On The Weld Bead Profile And Its Prediction For Hot Wire Arc Additive Manufacturing, Niraj Pudasaini

Electronic Theses and Dissertations

Wire arc additive manufacturing is a process of making three-dimensional metal parts in a layer-by-layer approach using a feed wire and electric arc as a heat source. Wire arc additive manufacturing (WAAM) is becoming more popular due to its ability to create complex 3D parts, less build time, high deposition rate, and significant cost savings. Out of the many parameters used in WAAM, one of the important parameters is shielding gas which plays a significant role in material quality, properties, and defects. In this study, a controlled amount of Argon (Ar) and Nitrogen (N₂) shielding gases are used …

Numerical Investigation Of Coalescence-Induced Self-Propelled Behavior Of Droplets On Non-Wetting Surfaces And Wedged Surfaces., Yan Chen

Electronic Theses and Dissertations

When small drops coalesce on a superhydrophobic surface, the merged drop can jump away from the surface due to the surface energy released during the coalescence. This self-propelled behavior has been observed on various superhydrophobic surfaces and has potential applications in areas related to the heat and mass transfer, such as heat exchangers, anti-icing and anti-frost devices, thermal management and water harvesting. The jumping velocity model was obtained based on published experimental data and the balance of various energy terms described in previous studies. However, the self-propelled mechanism is still not fully understood. In this study, the self-propelled droplet phenomenon …

Blade Design And Analysis Of Horizontal-Axis Wind Turbine: Cfd And Experimental Investigation Of Blades Design, Relwinde Fabrice Zongo

Electronic Theses and Dissertations

The present thesis focuses on the investigations of the computational fluid dynamics analysis and the experimental study of small scales Horizontal Axis Wind Turbine (HAWT) blades. The initial steps are taken; in the process of this research were the selection of the airfoil type to be used in each blade design and the creation of a blade design with high efficiency operating in a low wind speed zone. For the mentioned blade design process, the following airfoils were selected respectively NACA 0010, NACA 0012, NACA 1412, NACA 2412, NACA 2414, NACA 4412 and NACA 6412. This selection intends to provide …

Geometric Optimization Of A Heaving Point Absorber Wave Energy Converter, Ian Riley

Electronic Theses and Dissertations

Wave energy shows significant potential for development into a competitive renewable energy source. Non-renewable resources are finite and contribute to adverse effects on the environment. Development of wave energy conversion devices that use heave motion as the primary driver for converting wave energy into electrical potential is explored through optimizing the geometry of an axisymmetric partially submerged buoy in deep water. The governing equations of motion and hydrodynamic forces are solved for in one degree of freedom using ANSYS Aqwa. An external PTO device is simulated to induce power capture in the system. Four different geometric shapes are tested and …

Transformation Of Nonlinear Waves In The Presence Of Wind, Current, And Vegetation, Haifei Chen

Electronic Theses and Dissertations

Accurate prediction of extreme wave events is crucial for the safe maritime activities and offshore operations. Improved knowledge of wave dissipation mechanisms due to breaking and vegetation leads to accurate wave forecast, protecting life and property along the coast. The scope of the thesis is to examine the wave transformations in the presence of wind, current, and vegetation, using a two-phase flow solver based on the open-source platform OpenFOAM. The Reynolds-Averaged Navier-Stokes (RANS) equations are coupled with a Volume of Fluid (VOF) surface capturing scheme and a turbulence closure model. This RANS-VOF model is adapted to develop a numerical wind-wave-current …

Assessment Of Varying Model Representations In Cfd Simulations, Caitlin R. Gerdes

Electronic Theses and Dissertations

This thesis investigates the effects of varying model refinement and representation of computational fluid dynamics (CFD) simulations in two case studies. Product and process realization in engineering design requires substantial resources (time and money) in order to test novel designs for effectiveness. In recent decades, engineering has been relying more heavily on simulation-based analysis in the design process with computer models to help reduce the demands for real-life testing. The first case study analyzed in this thesis is a photobioreactor, which is used to grow microalgae for biofuel and require a balance of nutrients, light, and mixing for growth. The …

Application Of The Aeroacoustic Analogy To A Shrouded, Subsonic, Radial Fan., Bryan Buccieri

Electronic Theses and Dissertations

A study was conducted to investigate the predictive capability of computational aeroacoustics with respect to a shrouded, subsonic, radial fan. A three dimensional unsteady fluid dynamics simulation was conducted to produce aerodynamic data used as the acoustic source for an aeroacoustics simulation. Two acoustic models were developed: one modeling the forces on the rotating fan blades as a set of rotating dipoles located at the center of mass of each fan blade and one modeling the forces on the stationary fan shroud as a field of distributed stationary dipoles. Predicted acoustic response was compared to experimental data. The blade source …

Computational And Experimental Study On Vertical Axis Wind Turbine In Search For An Efficient Design, Mohammad M. Bashar

Electronic Theses and Dissertations

Wind alone can fulfill most of the energy requirement of the world by its efficient conversion in to energy. Though Horizontal Axis Wind Turbine (HAWT) is more popular but needs high wind speed to generate energy. On the other hand Vertical Axis Wind Turbine (VAWT) needs low wind speed and can be installed anywhere which are some of the reasons for this research. The main objective of this research is to improve the design and performance of VAWT to make it more attractive, efficient, durable and sustainable. For a VAWT the blades perform the main role to extract energy from …

Cavitation In Pharmaceutical Manufacturing And Shipping, Donn Sederstrom

Electronic Theses and Dissertations

Therapeutic proteins are used to successfully treat hemophilia, Crohn's Disease, diabetes, and cancer. Recent product recalls have occurred because of sub-visible particle formation resulting from the inherent instability of proteins. It has been suggested that particle formation is associated with late stage processing steps of filling, shipping, and delivery. Previous work at the University of Denver demonstrated that fluid cavitation can generate a large number of sub-visible protein particles in ultra clean formulations, but that mitigation can be achieved with fluid property manipulation. The goal of this research was to (1) assess the risk of cavitation under common pharmaceutical manufacturing …

Feature-Based Neuro-Symbolic Networks For Global Diagnostics, Tracy Lynn Schantz

Electronic Theses and Dissertations

Engineered system diagnostics have been researched over the years with many successful results. From transportation systems to office technologies, many have been equipped with self-diagnostic capabilities and are called Smart Machines. In spite of these advances, current diagnostic systems are driven by direct sensory information without much concern for patterns of the system behavior or features associated with them. For large-scale systems with complex dynamics, global as well as local diagnostics become of great importance, where sensory information is used as input for the local diagnostics, and patterns of behavior or features are utilized for global diagnostics.

The main objective …

Designing Of Energy Efficient Indoor Environments Using A Localized Radial Basis Function Meshless Method, Victor Huayamave

Electronic Theses and Dissertations

Around the world, the energy over consumption issue has been one of the key socio-economic and political challenges, which has drastically worsened over the last few years. Over the years engineers and environmentalists have proposed several approaches to improve energy efficiency. One is to reduce energy demand by improving consumption habits and a second approach is to introduce the use of a "greener" concept by using biomaterials in a diverse and more efficient manner in engineering construction to create energy efficient environments. This work will investigate the effects of using "green" stabilized earth materials to provide and enhance thermal regulation …