Mechanical Engineering Commons^™

Mechanics Of Pure Bending And Eccentric Buckling In High-Strain Composite Structures, Jimesh D. Bhagatji, Oleksandr G. Kravchenko, Sharanabasaweshwara Asundi

Mechanical & Aerospace Engineering Faculty Publications

To maximize the capabilities of nano- and micro-class satellites, which are limited by their size, weight, and power, advancements in deployable mechanisms with a high deployable surface area to packaging volume ratio are necessary. Without progress in understanding the mechanics of high-strain materials and structures, the development of compact deployable mechanisms for this class of satellites would be difficult. This paper presents fabrication, experimental testing, and progressive failure modeling to study the deformation of an ultra-thin composite beam. The research study examines the deformation modes of a post-deployed boom under repetitive pure bending loads using a four-point bending setup and …

Comparison Of Dynamics Stability Testing Techniques With Magnetic Suspension Wind Tunnel Capabilities, Otoniel A. Ramirez, Mark Schoenenberger, David E. Cox, Colin P. Britcher

Mechanical & Aerospace Engineering Faculty Publications

Dynamic stability testing techniques currently utilized at NASA Langley Research Center (LaRC) are conducted in multiple facilities and consists of free flight, forced oscillation, and free-to-oscillate tests. The NASA/ODU Magnetic Suspension and Balance System (MSBS) has been recommissioned to explore its utility as an additional facility to expand the dynamic stability test capabilities currently available at NASA LaRC. Simulations were created to replicate each current test facility and method as closely as possible. Data collected from the simulated environments was corrupted with replicated noise sources of the different testing environments and then compared to real data collected during tests when …

Exploring Additive Manufacturing In A Space Environment - A Capstone Design Project Experience, Zain Zafar Khan, Zachary Alan Sobelman, Sharanabasaweshwara Asundi

Mechanical & Aerospace Engineering Faculty Publications

The employment of additive manufacturing in the non-standard environments like space, ships, or submarines has the potential to be an advanced utility not only in the pre-flight production of aerospace components and structures, but also for the onboard manufacturing of components and tools necessary for future space missions. For example, the ability to produce tools and structural components on the International Space Station can provide the space community the opportunity to make repairs and upgrades to the space station without wasting time and resources transporting such materials through additional missions. Additive manufacturing would allow for space missions to use on …

Numerical Study Of The Time-Periodic Electroosmotic Flow Of Viscoelastic Fluid Through A Short Constriction Microchannel, Jianyu Ji, Shizhi Qian, Armani Marie Parker, Xiaoyu Zhang

Mechanical & Aerospace Engineering Faculty Publications

Electroosmotic flow (EOF) is of utmost significance due to its numerous practical uses in controlling flow at micro/nanoscales. In the present study, the time-periodic EOF of a viscoelastic fluid is statistically analyzed using a short 10:1 constriction microfluidic channel joining two reservoirs on either side. The flow is modeled using the Oldroyd-B (OB) model and the Poisson-Boltzmann model. The EOF of a highly concentrated polyacrylamide (PAA) aqueous solution is investigated under the combined effects of an alternating current (AC) electric field and a direct current (DC) electric field. Power-law degradation is visible in the energy spectra of the velocity fluctuations …

Topologically Optimized Electrodes For Electroosmotic Actuation, Jianwen Sun, Jianyu Zhang, Ce Guan, Teng Zhou, Shizhi Qian, Yongbo Deng

Mechanical & Aerospace Engineering Faculty Publications

Electroosmosis is one of the most used actuation mechanisms for the microfluidics in the current active lab-on-chip devices. It is generated on the induced charged microchannel walls in contact with an electrolyte solution. Electrode distribution plays the key role on providing the external electric field for electroosmosis, and determines the performance of electroosmotic microfluidics. Therefore, this paper proposes a topology optimization approach for the electrodes of electroosmotic microfluidics, where the electrode layout on the microchannel wall can be determined to achieve designer desired microfluidic performance. This topology optimization is carried out by implementing the interpolation of electric insulation and electric …

Editorial For The Special Issue On Micromachines For Non-Newtonian Microfluidics, Lanju Mei, Shizhi Qian

Mechanical & Aerospace Engineering Faculty Publications

In lieu of an abstract, this is an excerpt from the first page.

Microfluidics has seen a remarkable growth over the past few decades, with its extensive applications in engineering, medicine, biology, chemistry, etc [...]

Non-Equilibrium Behavior Of Large-Scale Axial Vortex Cores, Robert L. Ash, Irfan R. Zardadkhan

Mechanical & Aerospace Engineering Faculty Publications

A logical basis for incorporating pressure non-equilibrium and turbulent eddy viscosity in an incompressible vortex model is presented. The infrasonic acoustic source implied in our earlier work has been examined. Finally, this non-equilibrium turbulent vortex core is shown to dissipate mechanical energy more slowly than a Burgers vortex, helping us to explain the persistence of axial vortices in nature. Recent molecular dynamics simulations replicate aspects of this non-equilibrium pressure behavior.

Evaluation Of Murrell’S Ekf-Based Attitude Estimation Algorithm For Exploiting Multiple Attitude Sensor Configurations, Sharanabasaweshwara Asundi, Norman Fitz-Coy, Haniph Latchman

Mechanical & Aerospace Engineering Faculty Publications

Pico- and nano-satellites, due to their form factor and size, are limited in accommodating multiple or redundant attitude sensors. For such satellites, Murrell's implementation of the extended Kalman filter (EKF) can be exploited to accommodate multiple sensor configurations from a set of non redundant attitude sensors. The paper describes such an implementation involving a sun sensor suite and a magnetometer as attitude sensors. The implementation exploits Murrell's EKF to enable three sensor configurations, which can be operationally commanded, for satellite attitude estimation. Among the three attitude estimation schemes, (i) sun sensor suite and magnetometer, (ii) magnetic field vector and its …

Parametric Study Of A Turbofan Engine With An Auxiliary High-Pressure Bypass, Sharanabasaweshwara A. Asundi, Syed Firasat Ali

Mechanical & Aerospace Engineering Faculty Publications

A parametric study of a novel turbofan engine with an auxiliary high-pressure bypass (AHPB) is presented. The underlying motivation for the study was to introduce and explore a configuration of a turbofan engine which could facilitate clean secondary burning of fuel at a higher temperature than conventionally realized. The study was also motivated by the developments in engineering materials for high-temperature applications and the potential utility of these developments. The parametric study is presented in two phases. Phase I presents a schematic of the turbofan engine with AHPB and the mathematics of the performance parameters at various stations. The proposed …

Correlation Of Csk2sb Photocathode Lifetime With Antimony Thickness, M. A. Mamun, C. Hernandez-Garcia, M. Poelker, A. A. Elmustafa

Mechanical & Aerospace Engineering Faculty Publications

CsK₂Sb photocathodes with quantum efficiency on the order of 10% at 532 nm, and lifetime greater than 90 days at low voltage, were successfully manufactured via co-deposition of alkali species emanating from an effusion source. Photocathodes were characterized as a function of antimony layer thickness and alkali consumption, inside a vacuum chamber that was initially baked, but frequently vented without re-baking. Photocathode lifetime measured at low voltage is correlated with the antimony layer thickness. Photocathodes manufactured with comparatively thick antimony layers exhibited the best lifetime. We speculate that the antimony layer serves as a reservoir, or sponge, for …

Evaluation Of Niobium As Candidate Electrode Material For Dc High Voltage Photoelectron Guns, Mahzad Bastaninejad, Md. Abdulla Mohamed, Abdelmageed Elmustafa, P. Adderley, J. Clark, S. Covert, J. Hansknecht, C. Hernandez-Garcia, M. Poelker, R. Mammei, K. Surles-Law, P. Williams

Mechanical & Aerospace Engineering Faculty Publications

The field emission characteristics of niobium electrodes were compared to those of stainless steel electrodes using a DC high voltage field emission test apparatus. A total of eight electrodes were evaluated: two 304 stainless steel electrodes polished to mirrorlike finish with diamond grit and six niobium electrodes (two single-crystal, two large-grain, and two fine-grain) that were chemically polished using a buffered-chemical acid solution. Upon the first application of high voltage, the best large-grain and single-crystal niobium electrodes performed better than the best stainless steel electrodes, exhibiting less field emission at comparable voltage and field strength. In all cases, field emission …

Synthesis And Characterization Of Birnessite And Cryptomelane Nanostructures In Presence Of Hoffmeister Anions, Marcos A. Cheney, Robin Jose, Arghya Banerjee, Pradip K. Bhowmik, Shizhi Qian, Joseph M. Okoh

Mechanical & Aerospace Engineering Faculty Publications

The effect of Hoffmeister anions Cl(-), SO(4) (2-), and ClO(4) (-) on the structure and morphology of birnessite and cryptomelane-type manganese dioxide nanostructures, produced by the reduction reaction of KMnO(4) and MnSO(4) in aqueous acidic media, was studied. The syntheses were based on the decomposition of aqueous KMnO(4) in presence of HCl for birnessite-type and acidified MnSO4 for cryptomelane-type manganese dioxide under soft hydrothermal conditions. They were characterized using X-ray diffraction (XRD), transmission electron microscopy (TEM), and high-resolution transmission electron microscopy (HRTEM) techniques. XRD patterns show the formation of birnessite for the first synthesis and a mixture of cryptomelane and …

The Effect Of Stirring On The Morphology Of Birnessite Nanoparticles, Marcos A. Cheney, Pradip K. Bhowmik, Shingo Moriuchi, Mario Villabos, Shizhi Qian, Sang W. Joo

Mechanical & Aerospace Engineering Faculty Publications

The effect of mechanical stirring on the morphology of hexagonal layer- structure birnessite nanoparticles produced from decomposition of KMnO₄ in dilute aqueous H₂SO₄ is investigated, with characterization by X- ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), high- resolution transmission electron microscopy (HRTEM), thermogravimetric analysis (TGA), and N₂ adsorption (BET). Mechanical stirring during an initial stage of synthesis is shown to produce black birnessite containing nanofibers, whereas granular particulates of brown birnessite are produced without stirring. This is the first reduction synthesis of black birnessite nanoparticles with dendritic morphology without any use …

A New Method Of Synthesizing Black Birnessite Nanoparticles: From Brown To Black Birnessite With Nanostructures, Marcos A. Cheney, Pradip K. Bhowmik, Shizhi Qian, Sang W. Joo, Wensheng Hou, Joseph M. Okoh

Mechanical & Aerospace Engineering Faculty Publications

A new method for preparing black birnessite nanoparticles is introduced. The initial synthesis process resembles the classical McKenzie method of preparing brown birnessite except for slower cooling and closing the system from the ambient air. Subsequent process, including wet-aging at 7° C for 48 hours, overnight freezing, and lyophilization, is shown to convert the brown birnessite into black birnessite with complex nanomorphology with folded sheets and spirals. Characterization of the product is performed by X-ray diffraction (XRD), transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM), thermogravimetric analysis (TGA), and N(2) adsorption ( BET) techniques. Wet-aging and lyophilization times are …