Mechanical Engineering Commons^™

Development Of Economic Water Usage Sensor And Cyber-Physical Systems Co-Simulation Platform For Home Energy Saving, Joe Singer

Mechanical Engineering Master's Theses

In this thesis, two Cyber-Physical Systems (CPS) approaches were considered to reduce residential building energy consumption. First, a flow sensor was developed for residential gas and electric storage water heaters. The sensor utilizes unique temperature changes of tank inlet and outlet pipes upon water draw to provide occupant hot water usage. Post processing of measured pipe temperature data was able to detect water draw events. Conservation of energy was applied to heater pipes to determine relative internal water flow rate based on transient temperature measurements. Correlations between calculated flow and actual flow were significant at a 95% confidence level. Using …

Investigation Of 2195 And 2219 Post Weld Heat Treatments For Additive Friction Stir Lap Welds, Matthew Champagne

University of New Orleans Theses and Dissertations

To evaluate potential uses for friction stir welding in additive manufacturing, two separate parts were fabricated, one of 2195-T84 and the other 2219-T87, utilizing fixed pin techniques and additive lap welds. The parts were cut into samples, artificially aged and subjected to Rockwell hardness (HRB), Vickers hardness, micrographic photography, and metallographic imaging on both pre- and post- heat treatment. Additionally, tensile testing was performed on the heat-treated samples. A comparisons of test results showed a minimal increase in the yield strength of the 2195-T84 samples compared to as-welded tensile results obtained from a previous project. The ultimate tensile strength was …

Design, Manufacture, And Structural Dynamic Analysis Of A Biomimetic Insect-Sized Wing For Micro Air Vehicles, Jose Enrique Rubio

University of New Orleans Theses and Dissertations

The exceptional flying characteristics of airborne insects motivates the design of biomimetic wing structures that can exhibit a similar structural dynamic behavior. For this purpose, this investigation describes a method for both manufacturing a biomimetic insect-sized wing using the photolithography technique and analyzing its structural dynamic response. The geometry of a crane fly forewing (family Tipulidae) is acquired using a micro-computed tomography scanner. A computer-aided design model is generated from the measurements of the reconstructed scanned model of the insect wing to design the photomasks of the membrane and the venation network required for the photolithography procedure. A composite …

Application Of Pca To Cardiac Optical Mapping, Louis Woodhams

McKelvey School of Engineering Theses & Dissertations

Structural remodeling of the heart due to pathologies such as hypertension and myocardial infarction leads to the appearance of myofibroblasts, a phenotype largely absent in physiologic myocardium. While myofibroblasts are responsible for wound healing and structural repair of damaged myocardium, they are thought to have deleterious effects on electrical and mechanical properties of the heart. Understanding these effects is critical to developing effective treatments, and has motivated the development of a series of in vitro engineered heart tissues and cardiomyocyte-myofibroblast co-cultures whose mechanical and electrophysiological function can be deduced from video analysis. Electrophysiological properties are evident from changes in intensity …

Micro-Architectured Metamaterials: Design And Analysis, Li Ai

Mechanical Engineering Research Theses and Dissertations

Metamaterials are engineered materials with unusual properties deriving mainly from their micro-architectures rather than composition. They have attracted increasing attention owing to their tailorable multi-functional properties that cannot be exhibited by naturally-occurring or traditionally-manufactured materials. Materials with a negative Poisson’s ratio (PR) and materials with a non-positive coefficient of thermal expansion (CTE) are examples of mechanical metamaterials. In this dissertation, metamaterials with negative Poisson’s ratios and negative coefficients of thermal expansion are designed using both heuristic approaches and topology optimization methods.

Firstly, based on a star-shaped re-entrant structure, three two-dimensional (2-D) periodic cellular materials are developed, which can be tailored …

A Comparison Of The Aerodynamic Centers For Panel Code Compressible Corrections And Openfoam 5 For Mach 0.1 To 0.8, Dustin Weaver

All Graduate Plan B and other Reports, Spring 1920 to Spring 2023

It is known that the aerodynamic center changes from quarter chord to half chord from incompressible to compressible flows on airfoils. Compressible corrections are derived and implemented in a vortex panel code. These results will be used to find the aerodynamic centers for the specified Mach range of 0.1 to 0.8 in 0.1 increments within - 6 to 6 degrees angle of attack. OpenFOAM 5 cases will be created with specific meshes and settings. The results calculated from OpenFOAM 5 will be compared to the results obtained from the compressible corrections.

The Vibe, Sarah P. Douglass

Capstones

The Vibe is a long-form narrative about where tech is taking the female orgasm. The piece concludes that physiological research is a required next step when creating the climax of the future.

http://sarahpdouglass.com

Dynamic Modeling And Extreme Tension Analysis Of Mooring System For A Floating Offshore Wind Turbine, Wei Ting Hsu

Electronic Theses and Dissertations

For offshore wind industry, exploiting the dynamic behaviors of mooring lines is of increasing importance in floating offshore wind turbine (FOWT) mooring system design. Currently, the design philosophy for structures and moorings is based on principles and practices adopted in offshore oil and gas, including mooring systems that are optimized for applications in deeper waters. However, the design of FOWT mooring systems is facing several challenges, including installation costs, the stability of light-weight minimalistic platforms, and shallow water depths (50-300m). The extreme tension in mooring lines of a light displacement platform in shallow water is dominated by snap loads. Hence …

Modeling Of A Head - Neck Assembly Drop Tower Impact Test Using Abaqus, Hussein Sharqi Owaid

Electronic Theses and Dissertations

There are numerous potential causes of traumatic brain injury (TBI) and concussions, including traffic accidents, contact during sports and falls. Protection from these injuries is paramount because of the problems that result from TBI, such as loss of thinking and memory capability. Head impact from falls, especially in elderly, can also result in severe to fatal injury and some effects of brain injury are often not visible. For these reasons and more a need exists for protective head gear that can keep persons safe during at risk physical activity and that can protect fall prone persons from accidental injuries. Part …

The Inter-Laminar Shearing Effect On Wrinkle Development In Composite Forming Processes, David Sundquist

McKelvey School of Engineering Theses & Dissertations

Composite materials are becoming prevalent in aerospace industries as the uniqueness of the composite structure allows the composite to be tailored specifically for individual applications. Many fabrication techniques produce defects in composite parts such as wrinkles, fiber waviness, fiber misalignment, and porosity. The driving mechanisms behind these defects occurring during forming processes are not fully understood and, thus, characterization formation of these defects in a uncured state is beneficial to optimize composite processing. This work primarily investigated the influence of how uncured pre-impregnated carbon ply properties affect the wrinkling behavior of a composite laminates. Several factors affecting composite ply forming …

Characterizing Anisotropy In Fibrous Soft Materials By Mr Elastography Of Slow And Fast Shear Waves, John Larson Schmidt

McKelvey School of Engineering Theses & Dissertations

The general objective of this work was to develop experimental methods based on magnetic resonance elastography (MRE) to characterize fibrous soft materials. Mathematical models of tissue biomechanics capable of predicting injury, such as traumatic brain injury (TBI), are of great interest and potential. However, the accuracy of predictions from such models depends on accuracy of the underlying material parameters. This dissertation describes work toward three aims. First, experimental methods were designed to characterize fibrous materials based on a transversely isotropic material model. Second, these methods are applied to characterize the anisotropic properties of white matter brain tissue ex vivo. Third, …

Impact Of Flow Direction On Local Flow Behavior In Biologically-Inspired Flow Passages, Derrick Dewayne Herrin

Honors College Theses

ABSTRACT

A computational fluid dynamics model was utilized to study the effect of flow direction on local flow behavior in biologically-inspired microscale flow networks. Biologically-inspired flow networks have been found to offer numerous advantages when compared with parallel flow networks, particularly in thermal management applications. Flow behavior was examined for a range of bifurcation angles and laminar inlet Reynolds numbers. The computational model was validated with existing theoretical solutions and verified for grid independence. As the bifurcation angle increased, the pressure drop, and thus pumping power, across the biologically-inspired flow networks increased. In addition, as the inlet Reynolds number increased, …

Co-Simulation Framework For Power Distribution System Analysis With Humans In The Loop, Victor H. Ayon

Mechanical Engineering ETDs

Recent developments in the area of power generation have led to an increased penetration of storage and distributed energy resources (DER) in power distribution systems. As a result, new and enhanced energy management systems will be necessary as the deployment of DERs, as well as the need to control loads, continues to increase in the coming years. Advanced management systems are especially important to achieve resilient power delivery during emergency situations. During a blackout for example, a section of a distribution feeder could island to operate as a microgrid to ensure critical services such as water, food, and medical care …

Multiphase Flow Modeling For Design And Optimization Of A Novel Down-Flow Bubble Column, Mutharasu Lalitha Chockalingam

LSU Doctoral Dissertations

The application of the Euler-Euler framework based Computational Fluid Dynamics (CFD) models for simulating the two-phase gas-liquid bubbly flow in down-flow bubble columns is discussed in detail. Emphasis is given towards the modelling and design optimization of a novel down-flow bubble column. The design features of this novel down-flow bubble column and its advantages over a conventional Plunging Jet down-flow bubble column are discussed briefly. Then, some of the present challenges in simulating a conventional Plunging Jet down-flow bubble column in the Euler-Euler framework is highlighted, and a sigmoid function based drag modification function is implemented to overcome those challenges. …

Habitat Use Of Blacktip Sharks (Carcharhinus Limbatus) At Fishing Piers, Kelsey L. Spencer

Electronic Theses and Dissertations

Blacktip sharks (Carcharhinus limbatus) can be observed near fishing piers throughout the summer along the northeast coast of South Carolina. These piers attract and support a wide variety of potential prey and sharks are able to forage on fishers’ discards with minimal energetic cost. I tagged 12 blacktip sharks with acoustic transmitters, monitored piers with acoustic receivers, and conducted pier-creel surveys to determine the habitat use of blacktip sharks at fishing piers, factors that influenced residence time and presence/absence at piers, and any cyclical patterns in visits to piers. Data were analyzed with pier association indices (PAI), mixed models, and …

Heterogeneous Anisotropy Index And Scaling In Multiphase Random Polycrystals, Muhammad Ridwan Murshed

Theses and Dissertations

Under consideration is the finite-size scaling of elastic properties in single and two-phase random polycrystals with individual grains belonging to any crystal class (from cubic to triclinic). These polycrystals are generated by Voronoi tessellations with varying grain sizes and volume fractions. By employing variational principles in elasticity, we introduce the notion of a 'Heterogeneous Anisotropy Index' and investigate its role in the scaling of elastic properties at finite mesoscales. The index turns out to be a function of 43 variables, 21 independent components for each phase and the volume fraction of either phase. Furthermore, the relationship between Heterogeneous Anisotropy Index …

Low-Cost Control Engineering Experiments, Megan Arduin

Honors Theses

The disciplines found within the area of motion and controls is a vital element of each engineer’s education. The ability to understand and then control dynamic systems is a fundamental skill required for many working engineers today. The aim of this project is to further develop the tools and methods available to teach and prepare engineering students to effectively design control system architecture, and then successfully implement their design into real world systems. The main goal is to design an apparatus that can be used to teach control system methods and has an affordable price. There are few experiments where …

Boat-Lift Design And Analysis, Nathan Schick

Honors Theses

A current in production 6000 lb. rated boat-lift is being sold at “Great Lake Lifts”. The lift was tested experimentally and proved to hold at least 8000 lb. The design team successfully modeled the current lift on Ansys to help the customer understand where the weakest points in the design were. Following the creation of the initial lift design, the design team proposed and tested modifications that could be made in order to make the lift more structurally sound. The initial lift had a maximum deflection of 0.43846 inches, a maximum stress of 15880 psi, and a safety factor of …

Dynamic In Vivo Skeletal Feature Tracking Via Fluoroscopy Using A Human Gait Model, William Patrick Anderson

Doctoral Dissertations

The Tracking Fluoroscope System II, a mobile robotic fluoroscopy platform, developed and built at the University of Tennessee, Knoxville, presently employs a pattern matching algorithm in order to identify and track a marker placed upon a subject’s knee joint of interest. The purpose of this research is to generate a new tracking algorithm based around the human gait cycle for prediction and improving the overall accuracy of joint tracking.

This research centers around processing the acquired x-ray images of the desired knee joint obtained during standard clinical operation in order to identify and track directly through the acquired image. Due …

Deep Well Pump Seal, Peter M. Gordon, Matt C. Johnson, Dylan A. Smith

Mechanical Engineering

Lifewater International, a Christian non-profit, trains locals to repair water well hand pumps in various third world countries. It would be beneficial to retrofit difficult-to-repair hand pumps with a locally-made pump cylinder such as HydroMission's "SlapShot". The majority of the components in the "SlapShot" can be easily obtained in rural third world villages. However, the thick leather gaskets required to seal the water cylinder during the pumping operation are imported. These thick leather gaskets are expensive, and when they fail, this results in pumps being out of commission for extended periods of time. Lifewater has presented this problem to a …

Dyno-Mite Redesign, Brandon Joseph Miller, Daniel Robert Hoffman, Richard Demedici Young

Mechanical Engineering

The Cal Poly Mechanical Control Systems Laboratory currently employs an outdated device, known as the Motomatic, to teach students about various motor characteristics and control methods. These include open-loop vs. closed-loop control, speed vs. position control, and DC motor response curves. The current device does not function properly and produces unreliable data due to overwhelming non-linear effects such as stiction and shaft misalignment. Our team was tasked with designing a replacement device that retains many of the same educational goals as the original lab procedure, while also adding new educational goals pertaining to the device system dynamics. The new apparatus, …

Rogue Rotary - Modular Robotic Rotary Joint Design, Sean Wesley Murphy, Tyler David Riessen, Jacob Mark Triplett

Mechanical Engineering

This paper describes the design process from ideation to test validation for a singular robotic joint to be configured into a myriad of system level of robots.

Real Time And High Fidelity Quadcopter Tracking System, Tyler Mckay Hall

Computer Engineering

This project was conceived as a desired to have an affordable, flexible and physically compact tracking system for high accuracy spatial and orientation tracking. Specifically, this implementation is focused on providing a low cost motion capture system for future research. It is a tool to enable the further creation of systems that would require the use of accurate placement of landing pads, payload acquires and delivery. This system will provide the quadcopter platform a coordinate system that can be used in addition to GPS.

Field research with quadcopter manufacturers, photographers, agriculture and research organizations were contact and interviewed for information …

Exploring Energy, Comfort, And Building Health Impacts Of Deep Setback And Normal Occupancy Smart Thermostat Implementation, Zachary Ethan Alderman

Graduate Theses and Dissertations

As smart thermostat adoption rates continue to increase, it becomes worthwhile to explore what unanticipated outcomes may result in their use. Specific attention was paid to smart thermostat impacts to deep setback and normal occupancy states in a variety of conditions while complying with the ventilation and temperature requirements of ASHRAE 90.2-2013. Custom weather models and occupancy schedules were generated to efficiently explore a combination of weather conditions, building constructions, and occupancy states. The custom modeling approach was combined with previous experimental data within the Openstudio graphics interface to the EnergyPlus building modeling engine. Results indicate smart thermostats add the …

Development Of An Insulated Solar Electric Cooker (Isec) With Thermal Storage For Use In Developing World Countries, Amanda Gyokery, Spencer W. Davis, Kyle Henry Smit

Mechanical Engineering

According to the World Health Organization, about half of the world’s population uses biomass stoves to cook their meals. However, biomass fires can be dangerous. Unattended biomass fires and indoor air pollution are responsible for an estimated 600,000 deaths annually and the creation of approximately 4 million instances of chronic disease. They also release CO2 and other pollutants into the air, and require the families to gather enough material to keep it burning (WHO 2017). Although cleaner cooking technology seems like a clear solution, often families are either unwilling to change how they cook food or are unable to afford …

Museum Wave Tank Design, David James Streng, Lisa Michelle Dischinger, John Frederick Niemoller

Mechanical Engineering

The Santa Maria Discovery Museum would like to add a tsunami wave tank to be one of their demonstrations. The wave tank needs to draw the attention of their young crowd and be educationally informative about the shapes and effects of waves. As this is a museum demonstration for children, the structure, user interface, and wave making mechanism must be durable.

We are a senior project team from California Polytechnic State University that worked on this project with Allan Hancock College and Stanford University. We created waves by rapidly moving a plunger vertically in the water column. This project allows …

Usa Boccia Ball Ramp For Athletes With Quadriplegia, Alissa A. Koukourikos, Matthew Lee, Nathan Bernards

Mechanical Engineering

In this report, the design process in creating an assistive device for Boccia Classification 3 (BC3) players is outlined. The initial research steps, including research into the rules of the game, capabilities of the players, and existing products is documented to show where ideas for the product stemmed from. This transitions into requirements that the sponsor requested, and preliminary designs and ideas for the product. Finally, this report explains the details of the final design, which has been analyzed for safety, ease of use, and ability to function under different conditions. The processes of manufacturing and testing will also be …

Poly Spotlight Control, Ryan P. O'Neill, C. Oleg Frandle, Anthony T. Lombardi

Mechanical Engineering

When this project began, The Cambria Center for the Arts Theater used a manually-operated spotlight. The sound created by the fans, along with the sheer size of the spotlight, required that it be housed in an attic room above the theater and shined through a closed window. This trapped a lot of heat in the room and involved some risk with climbing into and out of the attic room. This project sought to remedy those issues by mounting a pair of newer LED spotlights inside the theater. Doing this required a method for remotely controlling and actuating the angular position …

Electrochemical Detection Of Low-Concentration Lead (Ii) Ions From Water, Mohmmad Rizwen Ur Rahman

Theses and Dissertations

The aim of this study was to develop an electrochemical sensor for speedy, selective and sensitive detection of lead ion (Pb2+) using graphene oxide and pyrrole nanocomposite. Different combinations of graphene oxide and pyrrole in layers and mixtures were tested for the finest sensitive detection of lead ion (Pb2+). Reduced graphene oxide and polypyrrole (rGO-PPY as layer) nanocomposite modified screen printed electrode (SPE) showed the best signal in response to the differential pulse anodic stripping voltammetry (DPASV) with a limit of detection to 5 ppb. The rGO-PPY modified electrode possessed a large effective surface area because of the unique 3D …

Theoretical And Experimental Investigation On The Multiple Shape Memory Ionic Polymer-Metal Composite Actuator, Qi Shen

UNLV Theses, Dissertations, Professional Papers, and Capstones

Development of biomimetic actuators has been an essential motivation in the study of smart materials. However, few materials are capable of controlling complex twisting and bending deformations simultaneously or separately using a dynamic control system. The ionic polymer-metal composite (IPMC) is an emerging smart material in actuation and sensing applications, such as biomimetic robotics, advanced medical devices and human affinity applications. Here, we report a Multiple Shape Memory Ionic Polymer-Metal Composite (MSM-IPMC) actuator having multiple-shape memory effect, and is able to perform complex motion by two external inputs, electrical and thermal. Prior to the development of this type of actuator, …