Mechanical Engineering Commons^™

The Inter-Laminar Shearing Effect On Wrinkle Development In Composite Forming Processes, David Sundquist

McKelvey School of Engineering Theses & Dissertations

Composite materials are becoming prevalent in aerospace industries as the uniqueness of the composite structure allows the composite to be tailored specifically for individual applications. Many fabrication techniques produce defects in composite parts such as wrinkles, fiber waviness, fiber misalignment, and porosity. The driving mechanisms behind these defects occurring during forming processes are not fully understood and, thus, characterization formation of these defects in a uncured state is beneficial to optimize composite processing. This work primarily investigated the influence of how uncured pre-impregnated carbon ply properties affect the wrinkling behavior of a composite laminates. Several factors affecting composite ply forming …

Effect Of Ultrasonic Treatment On The Microstructure And Mechanical Properties Of Al6061 And Composite, Ana S. Exime

FIU Electronic Theses and Dissertations

In this study, the effect of ultrasonic treatment (UST) parameters such as amplitude, sonication time, and melt temperature on microstructure and microhardness of Al 6061 alloy is evaluated. The effect of UST on the dispersion of tungsten disulfide (WS₂) and carbon nanotubes (CNT) as reinforcement particles in Al 6061 during casting is also studied. The cast Al 6061 with UST demonstrated 32% grain size reduction and 8% increase in the microhardness for optimum processing conditions. The cavitation process induced by UST is responsible for the refinement in microstructure and increase of hardness by enhancing the degassing and nucleation …

Method For Single Crystal Growth Of Photovoltaic Perovskite Material And Devices, Jinsong Huang, Qingfeng Dong

Department of Mechanical and Materials Engineering: Faculty Publications

Systems and methods for perovskite single crystal growth include using a low temperature solution process that employs a temperature gradient in a perovskite solution in a container , also including at least one small perovskite single crystal , and a substrate in the solution upon which substrate a perovskite crystal nucleates and grows , in part due to the temperature gradient in the solution and in part due to a temperature gradient in the substrate . For example , a top portion of the substrate external to the solution may be cooled .

Oct-Based Three Dimensional Modeling Of Stent Deployment, Pengfei Dong, David Prabhu, David L. Wilson, Hiram G. Bezerra, Linxia Gu

Department of Mechanical and Materials Engineering: Faculty Publications

Stent deployment has been widely used to treat narrowed coronary artery. Its acute outcome in terms of stent under expansion and malapposition depends on the extent and shape of calcifications. However, no clear understanding as to how to quantify or categorize the impact of calcification. We have conducted ex vivo stenting characterized by the optical coherence tomography (OCT). The goal of this work is to capture the ex vivo stent deployment and quantify the effect of calcium morphology on the stenting. A three dimensional model of calcified plaque was reconstructed from ex vivo OCT images. The crimping, balloon expansion and …

Multiple Scattering Theory For Polycrystalline Materials With Strong Grain Anisotropy: Theoretical Fundamentals And Applications, Huijing He

Department of Mechanical and Materials Engineering: Faculty Publications

This work is a natural extension of the author’s previous work: “Multiple scattering theory for heterogeneous elastic continua with strong property fluctuation: theoretical fundamentals and applications” (arXiv:1706.09137 [physics.geo-ph]), which established the foundation for developing multiple scattering model for heterogeneous elastic continua with either weak or strong fluctuations in mass density and elastic stiffness. Polycrystalline material is another type of heterogeneous materials that widely exists in nature and extensively used in industry. In this work, the corresponding multiple scattering theory for polycrystalline materials with randomly oriented anisotropic crystallites is developed. To validate the theory, the theoretical results for a series of …

Floating-Gate Transistor Photodetector, Jinsong Huang, Yongbo Yuan

Department of Mechanical and Materials Engineering: Faculty Publications

A field effect transistor photodetector that can operate in room temperature includes a source electrode , a drain electrode , a channel to allow an electric current to flow between the drain and source electrodes , and a gate electrode to receive a bias voltage for controlling the current in the channel . The photodetector includes a light - absorbing mate rial that absorbs light and traps electric charges . The light absorbing material is configured to generate one or more charges upon absorbing light having a wavelength within a specified range and to hold the one or more charges …

Software For Extracting Deformation Gradient And Stress From Md Simulations: Simulations Using The Charmm Force Field, Mehrdad Negahban, Lili Zhang, Zesheng Zhang, John Jasa, Antoine Jérusalem

Department of Mechanical and Materials Engineering: Faculty Publications

Software was developed, and is provided under a general use license, to calculate continuum level deformation gradient and stress for any group of atoms in an MD simulation that uses the Charmm force fields. This software can also calculate the interaction stress applied by one group of atoms on any other group. To obtain deformation gradient and stress, the user needs to provide the selected group(s) of atoms in an atom group identification file, and provide the associated LAMMPS format files and force field parameter file. An example is included to demonstrate the use of the software.

Energy Absorbing Guardrail System, John R. Rohde, John D. Reid, King K. Mak, Dean L. Sicking

Department of Mechanical and Materials Engineering: Faculty Publications

A highway crash attenuation system having W - beam rail elements attached to a plurality of vertical posts . An impact terminal with a feeder chute guides one or more of the W - beam rail elements through the impact terminal . The feeder chute has an impact shield extending along a traffic facing side of the chute from an upstream - most end to a downstream - most end of the chute closing the traffic - facing side of the chute . The system also has an anchor cable release mechanism for releasing the cable downstream of the first …

Shape-Adaptive Mechanism For Robotic Grasping, Carl A. Nelson

Department of Mechanical and Materials Engineering: Faculty Publications

A grapser can include a first pantograph cell and a second pantograph cell coupled with the first pantogrpah cell. The first and second pantograph cells can be coupled together at a first pivot and a second pivot. The grasper can also include a finger extendable in a direction extending between the first pivot and the second pivot. The grasper can include a support base, where one or more links of the first pantograph cell can be slidably coupled with the support base for extending the grasper. In some embodiment, the grasper can be configured to extend along a curved path. …

Simulating Dynamic Failure Of Polymer-Bonded Explosives Under Periodic Excitation, Rachel Kohler, Camilo Duarte Cordon, Marisol Koslowski

The Summer Undergraduate Research Fellowship (SURF) Symposium

Accidental mishandling of explosive materials leads to thousands of injuries in the US every year. Understanding the mechanisms behind the detonation process is crucial to prevent such accidents. In polymer-bonded explosives (PBX), high-frequency mechanical excitation generates thermal energy and can lead to an increase in temperature and vapor pressure, and potentially the initiation of the detonation process. However, the mechanisms behind this energy release, such as the effects of dynamic fracture and friction, are not well understood. Experimental data is difficult to collect due to the different time scales of reactions and vibrations, so research is aided by running simulations …

A Parametric Study Of The Mechanics Of Different Skin Flap Techniques, Steven J. Meza, Adrián Tepole Buganza

The Summer Undergraduate Research Fellowship (SURF) Symposium

In modern day plastic and reconstructive surgeries numerous skin flap designs have been developed and are used to close open wounds. Skin flaps are developed with the intention of imposing minimal tension in skin closure. Excessive tension can lead to poor blood flow that result in post-surgery complications such as necrosis. Currently there is no standard in choosing a skin flap design and a surgeon's choice is based personal experience. A comparison of the mechanical loading in these various designs has not yet been done. We have developed a parametric study, using finite element analysis, of two advancement skin flaps …

Development Of The End-Effector Of A Cable-Driven Parallel Manipulator For Automated Crop Sensing, Iman Salafian

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

A four cable-driven parallel manipulator (4CDPM), consisting of sophisticated spectrometers and imagers, is under development for use in acquiring phenotypic and environmental data over an acre-sized maize field. This thesis presents the design, controls, and testing of two sub-systems in a 4CDPM: a Center of Mass Balance System (CMBS) and a Drop-Down System (DDS).

One of the factors that influences stability is the center of mass (COM) position of the end effector. An offset in COM can cause a pendulum effect or an undesired tilt angle. A center of mass balancing system is presented in this thesis to minimize the …

Meniscus-Assisted Solution Printing Of Largegrained Perovskite Films For High-Efficiency Solar Cells, Ming He, Bo Li, Xun Cui, Beibei Jiang, Yanjie He, Yihuang Chen, Daniel O'Neil, Paul Szymanski, Mostafa A. El-Sayed, Jinsong Huang, Zhiqun Lin

Department of Mechanical and Materials Engineering: Faculty Publications

Control over morphology and crystallinity of metal halide perovskite films is of key importance to enable high-performance optoelectronics. However, this remains particularly challenging for solution-printed devices due to the complex crystallization kinetics of semiconductor materials within dynamic flow of inks. Here we report a simple yet effective meniscus-assisted solution printing (MASP) strategy to yield large-grained dense perovskite film with good crystallization and preferred orientation. Intriguingly, the outward convective flow triggered by fast solvent evaporation at the edge of the meniscus ink imparts the transport of perovskite solutes, thus facilitating the growth of micrometre-scale perovskite grains. The growth kinetics of perovskite …

Dissipative Elastic Metamaterial With A Lowfrequency Passband, Yongquan Liu, Jianlin Yi, Zheng Li, Xianyue Su, Wenlong Li, Mehrdad Negahban

Department of Mechanical and Materials Engineering: Faculty Publications

We design and experimentally demonstrate a dissipative elastic metamaterial structure that functions as a bandpass filter with a low-frequency passband. The mechanism of dissipation in this structure is well described by a mass-spring-damper model that reveals that the imaginary part of the wavenumber is non-zero, even in the passband of dissipative metamaterials. This indicates that transmittance in this range can be low. A prototype for this viscoelastic metamaterial model is fabricated by 3D printing techniques using soft and hard acrylics as constituent materials. The transmittance of the printed metamaterial is measured and shows good agreement with theoretical predictions, demonstrating its …

Multiple Scattering Theory For Heterogeneous Elastic Continua With Strong Property Fluctuation: Theoretical Fundamentals And Applications, Huijing He

Department of Mechanical and Materials Engineering: Faculty Publications

Scattering of elastic waves in heterogeneous media has become one of the most important problems in the field of wave propagation due to its broad applications in seismology, natural resource exploration, ultrasonic nondestructive evaluation and biomedical ultrasound. Nevertheless, it is one of the most challenging problems because of the complicated medium inhomogeneity and the complexity of the elastodynamic equations. A widely accepted model for the propagation and scattering of elastic waves, which properly incorporates the multiple scattering phenomenon and the statistical information of the inhomogeneities is still missing. In this work, the author developed a multiple scattering model for heterogeneous …

A Strategy To Optimize Recovery In Orthopedic Sports Injuries, Michael P. Sealy, Ziye Liu, Chao Li, Yuebin Guo, Ben White, Mark Barkey, Brian Jordon J, Luke N. Brewer, Dale Feldman

Department of Mechanical and Materials Engineering: Faculty Publications

An important goal for treatment of sports injuries is to have as short a recovery time as possible. The critical problem with current orthopedic implants is that they are designed to be permanent and have a high complication rate (15%) that often requires removal and replacement with a second surgery; and subsequently a second rehabilitation cycle. This study was designed to test the feasibility of having a device that could provide the needed mechanical properties, while promoting healing, for a specified amount of time and then degrade away, to shorten the recovery time. The specific strategy was to create a …

Development Of 3d Compression Molded Composite Primary Structure, Sean D. Tischler, Jacob H. Goldstein, Alea A. Perez

Mechanical Engineering

The work accomplished by the Black Gold team improved upon the carbon fiber compression molding research and information available on the Cal Poly San Luis Obispo campus. The team used the rear suspension rocker arm off a Ventana Alpino mountain bike as a design goal for this project. This research and body of work includes the methods used to design a compression molded part for complex part loading and shape. This extends to the process of choosing an appropriate layup process, in addition to benefits and drawbacks of the use of chopped fibers in compression molding. The research includes the …

Deployable Antenna For Cubesat, Mackenzie Thomas Lennon, Caleb Andrew Barber, David Matthew Galves

Mechanical Engineering

This project is a proof-of-concept ground model of a large deployable antenna designed for the small space requirements of CubeSats. This small deployment module is designed to fit a 2 m by 1 m reflective antenna inside a storage volume of with the dimensions 20 cm by 20 cm x 40 cm. The reflector will be deployed to a parabolic shape with the goal of modeling the reflector necessary for high frequency communication. Because this module is designed as a proof-of-concept for the deployable parabolic reflector specifically, no electrical components will be incorporated and will just focus on the deployment …

The Mathematical Theory Of Deformation Arrest In Large-Strain Dynamic Plasticity, Brendan A. Kullback

Mechanical Engineering ETDs

Ductile structural components subjected to explosive loadings exhibit a large range of behaviors. The response of beams, walls, and blast doors is estimated using two methods. The engineering level approaches are highly simplified and neglect much of the relevant physics while the use of finite element or shock-code simulation is expensive and not suited to rapid problem solving and parameter studies. In this dissertation, a medium fidelity reduced order modeling approach has been derived to capture the most relevant physics governing rupture of ductile bodies dynamically deforming in tension.

Solution of the inertially stretching jet is used to reveal the …

Primary Blast Waves Induced Brain Dynamics Influenced By Head Orientations, Yi Hua, Yugang Wang, Linxia Gu

Department of Mechanical and Materials Engineering: Faculty Publications

There is controversy regarding the directional dependence of head responses subjected to blast loading. The goal of this work is to characterize the role of head orientation in the mechanics of blast wave-head interactions as well as the load transmitting to the brain. A three-dimensional human head model with anatomical details was reconstructed from computed tomography images. Three different head orientations with respect to the oncoming blast wave, i.e., front-on with head facing blast, back-on with head facing away from blast, and side-on with right side exposed to blast, were considered. The reflected pressure at the blast wave-head interface positively …

Negahban Group Report: Saw-Tooth Shear Response Of Aged Poly(Methyl Methacrylate) (Pmma), Mehrdad Negahban

Department of Mechanical and Materials Engineering: Faculty Publications

Results for isothermal saw-tooth shear loading experiments conducted on annealed and oven-cooled poly(methyl methacrylate) (PMMA) at temperatures between 50^oC and 140^oC. The experiments were conducted 1996.

Formation Of Mound-Like Multiscale Surface Structures On Titanium By Femtosecond Laser Processing, Edwin Peng, Alfred Tsubaki, Craig A. Zuhlke, Ryan Bell, Meiyu Wang, Dennis R. Alexander, George Gogos, Jeffrey E. Shield

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Surface Functionalization Technique • Femtosecond Laser Surface Processing (FLSP) • Utilize high power, femtosecond (10-15 s) laser pulses • Produce self-organized, multiscale surface micro/nanostructures • Diverse range of applicable substrates: semiconductors, metals, polymers, & composites

Why? • What are the different types of FLSP structures on Ti? • Physical evidence needed for FLSP formation models • Optimize FLSP of Ti for biomedical & other applications

How? • Obtain evidence of mound growth processes by examining underlying microstructure • Utilize dual beam Scanning Electron Microscope-Focused Ion Beam instrument to cross section surface structures & fabricate transmission electron microscopy samples

Dirichlet Process Gaussian Mixture Models For Real-Time Monitoring And Their Application To Chemical Mechanical Planarization, Jia (Peter) Liu, Omer F. Beyca, Prahalad K. Rao, Zhenyu (James) Kong, Satish T. S. Bukkapatnam

Department of Mechanical and Materials Engineering: Faculty Publications

The goal of this work is to use sensor data for online detection and identification of process anomalies (faults). In pursuit of this goal, we propose Dirichlet process Gaussian mixture (DPGM) models. The proposed DPGM models have two novel outcomes: 1) DP-based statistical process control (SPC) chart for anomaly detection and 2) unsupervised recurrent hierarchical DP clustering model for identification of specific process anomalies. The presented DPGM models are validated using numerical simulation studies as well as wireless vibration signals acquired from an experimental semiconductor chemical mechanical planarization (CMP) test bed. Through these numerically simulated and experimental sensor data, we …

Fabrication And Thermoelectric Characterization Of Stretchable Conductive Latex-Based Composites, Cory Michael Arcovitch

Graduate College Dissertations and Theses

Miniaturized stretchable electronic devices that can be bent and strained elastically without breaking, have drawn considerable research interest in recent years for wearable computers and integrated bio-sensor applications. Portable electrical power harvesting remains a critical challenge in flexible electronics materials. One proposed solution has been to convert waste heat from the human body into electricity using thermoelectric materials. Traditionally, however, these materials are brittle ceramic semiconductors with limited fracture resistance under deformation. The primary objective of this thesis is to address this challenge by fabricating and studying the mechanical, thermal and electrical performance of stretchable composites combining natural latex polymer …

Tensile Specimen Punch, John Allen

All Undergraduate Projects

This project comes from a need to have tensile specimens made for the MET 351, Metallurgy/Materials and Processes, and 426, Applied Strengths of Materials, labs. This punch is designed to be used with an arbor press to create the desired tensile specimen shape out of plastic blanks. The initial concept was suggested by Dr. Craig Johnson. The designs went through many changes, for example getting rid of the sides originally proposed to hold the specimen in place, and modifications to other parts to make them more efficient. Additional parts were also added to the design with the help and advice …

Detecting Laminate Damage Using Embedded Electrically Active Plies – An Analytical Approach, Amany Micheal, Yehia Bahei-El-Din

Centre for Advanced Materials

Assessment of damage initiation and progression in composite laminates with embedded electrically active plies is modeled. Utilizing electrically active layers embedded in composite laminates as damage sensors is proposed by several researchers and is mainly assessed experimentally. Sensing damage using embedded electrically active plies is generally preferred over the use of surface mounted PZT wafers since the range of the latter is limited to a very narrow area underneath the surface, while multiple damage mechanisms can generally be found in several plies of the laminate. The solution presented invokes two levels of analysis. Firstly, on the laminate level, applied membrane …

Vorticella: A Protozoan For Bio-Inspired Engineering, Sangjin Ryu, Rachel E. Pepper, Moeto Nagai, Danielle C. France

Department of Mechanical and Materials Engineering: Faculty Publications

In this review, we introduce Vorticella as a model biological micromachine for microscale engineering systems. Vorticella has two motile organelles: the oral cilia of the zooid and the contractile spasmoneme in the stalk. The oral cilia beat periodically, generating a water flow that translates food particles toward the animal at speeds in the order of 0.1–1 mm/s. The ciliary flow of Vorticella has been characterized by experimental measurement and theoretical modeling, and tested for flow control and mixing in microfluidic systems. The spasmoneme contracts in a few milliseconds, coiling the stalk and moving the zooid at 15–90 mm/s. Because the …

Benchmark Burnishing With Almen Strip For Surface Integrity, Z. Y. Liu, C. H. Fu, M. P. Sealy, Y. Zhao, Y. B. Guo

Department of Mechanical and Materials Engineering: Faculty Publications

Burnishing is a surface treatment process widely used in aerospace, navy and other industries to improve fatigue and corrosion resistance by introducing a compressive residual stress layer. The measurement of residual stress by XRD is expensive, time consuming, and tedious. This work presented a quick method to determine the residual stress by using Almen strips. Inspired by the application of Almen strips in shot peening, deflections of burnished Almen strips under different burnishing conditions were measured. It was found that the deflection of Almen strip reflects the magnitude and penetration depth into subsurface of induced stress. Higher burnishing force, smaller …

Methods , Systems , And Devices Relating To Surgical End Effectors, Shane M. Farritor, Tom Fredrick, Joe Bartels

Department of Mechanical and Materials Engineering: Faculty Publications

The embodiments disclosed herein relate to various medical device components, including components that can be incorporated into robotic and/or in vivo medical devices, and more specifically including end effectors that can be incorporated into such devices. Certain end effector embodiments include various vessel cautery devices that have rotational movement as well as cautery and cutting functions while maintaining a relatively compact structure. Other end effector embodiments include various end effector devices that have more than one end effector.

Comprehensive Finite Element Modeling Of Ti-6al-4v Cellular Solids Fabricated By Electron Beam Melting, Edel Arrieta

Open Access Theses & Dissertations

Additive manufacturing permits the fabrication of cellular metals which are materials that can be highly customizable and possess multiple and extraordinary properties such as damage tolerance, metamorphic and auxetic behaviors, and high specific stiffness. This makes them the subject of interest for innovative applications. With interest in these materials for energy absorption applications, this work presents the development of nonlinear finite element models in commercial software platforms (MSC Patran/Nastran) that permit the analysis of the deformation mechanisms of these materials under compressive loads. In the development of these models, a detailed multiscale study on the different factors affecting the response …