Mechanical Engineering Commons^™

Pre-Methylation Of Lignin To Improve Storage Stability Of Oil Produced By Solvent Liquefaction, Jae-Young Kim, Parinaz Hafezi-Sefat, Sarah D. Cady, Ryan G. Smith, Robert C. Brown

Sarah Cady

In this study, we methylated hydroxyl groups (phenolic hydroxyl: Phe-OH and aliphatic hydroxyl: Aliph-OH) in soda lignin (SL) prior to solvent liquefaction to improve storage stability of the resulting oil. We investigated two methylating reagents, dimethyl sulfate (DMS) and dimethyl carbonate (DMC), for selective Phe-OH and total hydroxyl group (Phe-OH and Aliph-OH) blocking. Samples of SL, DMS-SL, and DMC-SL were depolymerized into oils under supercritical ethanol (350 °C). Both methylated lignins produced higher amounts of oils and smaller amounts of char compared to untreated SL due to suppressed charring reactions. Oil produced from SL had relatively higher functional group contents …

Thermal Removal Of Carbon Dioxide From The Atmosphere: Energy Requirements And Scaling Issues, Ted Von Hippel

Ted von Hippel

I conduct a systems-level study of direct air capture of CO2 using techniques from thermal physics. This system relies on a combination of an efficient heat exchanger, radiative cooling, and refrigeration, all at industrial scale and operated in environments at low ambient temperatures. While technological developments will be required for such a system to operate efficiently, those developments rest on a long history of refrigeration expertise and technology, and they can be developed and tested at modest scale. I estimate that the energy required to remove CO2 via this approach is comparable to direct air capture by other techniques. The …

Developing A Workflow To Integrate Tree Inventory Data Into Urban Energy Models, Farzad Hashemi, Breanna L. Marmur, Ulrike Passe, Janette R. Thompson

Farzad Hashemi

Building energy simulation is of considerable interest and benefit for architects, engineers, and urban planners. Only recently has it become possible to develop integrated energy models for clusters of buildings in urban areas. Simulating energy consumption of the built environment on a relatively large scale (e.g., such as a neighborhood) will be necessary to obtain more reliable results, since building energy parameters are influenced by characteristics of the nearby environment. Therefore, the construction of a 3-D model of urban built areas with detail of the near-building environment should enhance simulation approaches and provide more accurate results. This paper describes the …

The Impact Of Trees On Passive Survivability During Extreme Heat Events In Warm And Humid Regions, Ulrike Passe, Janette R. Thompson, Baskar Ganapathysubramanian, Boshun Gao, Breanna L. Marmur

Breanna L. Marmur

Communities are increasingly affected by excessive heat. The likelihood of extreme heat events is predicted to increase in the Midwest region of the United States. By mid-century (2036–2065), one year out of 10 is projected to have a 5-day period that is 13°F warmer than a comparable earlier period (1976–2005). The frequency of high humidity/dew point days (“extra moist tropical air mass days,” MT++ synoptic climate classification system) has also increased significantly during a similar period (1975–2010) and between 2010 and 2014 included 8 of 26 heat events. This impact is exacerbated by the fact that many residences in low-income …

Effect Of Biomass Inlet Concentration On Mixing In A Double Screw Pyrolyzer, Breanna L. Marmur, Theodore J. Heindel

Breanna L. Marmur

The renewable energy industry relies on double screw pyrolyzers to convert cellulosic biomass into bio-oil. Bio-oil can then be converted into synthetic gasoline, diesel, and other transportation fuels, or can be converted into biobased chemicals for a wide range of applications. One of the processes by which bio-oil is produced in industry today is through fast pyrolysis, the fast thermal decomposition of organic material in the absence of oxygen. One type of pyrolyzer, a double screw pyrolyzer, features two intermeshing screws encased in a reactor which mechanically conveys and mixes the biomass and heat carrier media. The mixing effectiveness of …

Call For Abstracts - Resrb 2019, July 8-9, Wrocław, Poland, Wojciech M. Budzianowski

Wojciech Budzianowski

No abstract provided.

Fedsm 2018 Presentation, Nima Fathi, Peter Vorobieff, Seyed Sobhan Aleyasin, Goodarz Ahmadi

Nima Fathi

The Subject Librarian Newsletter, Nanoscience, Fall 2016, Sandy Avila

Sandy Avila

No abstract provided.

Extracting Vibration Characteristics Of A Guitar Using Finite Element, Modal Analysis, And Digital Image Correlation Techniques, Kiran Patil, Javad Baqersad, Daniel Ludwigsen, Yaomin Dong

Daniel Ludwigsen

The sound quality generated by the guitar depends on the vibration characteristics (i.e. natural frequencies and mode shapes) of this instrument. Thus, it is of particular interest to the guitar manufacturers to be able to obtain global information about the characteristics of the guitar. Traditional sensors can only measure at discrete locations. However, digital image correlation (DIC) can measure full-field data on the surface of the structure. In the current paper, a finite element (FE) model of a guitar with free boundary configurations was developed using quadratic solid elements. An eigensolution was performed on the FE model to determine its …

Prediction Of Solid Oxide Fuel Cell Performance Using Artificial Neural Network, M. A. Rafe Biswas, Kamwana N. Mwara

M. A. Rafe Biswas

Vector Acoustic Intensity Around A Tuning Fork, Daniel A. Russell, Justin Junell, Daniel O. Ludwigsen

Daniel Ludwigsen

The acoustic intensity vector field around a tuning fork is investigated. Theory for a longitudinal quadrupole source predicts a well-defined transition between near-field and far-field, with significant circulation of sound energy in the near-field. Vector components of the time-averaged intensity were measured using a two-microphone intensity probe and found to agree well with predictions from theory. The vector intensity map is interpreted, and shown to provide useful information about the near-field of an acoustic source.

Better Understanding Of Resonance Through Modeling And Visualization, Daniel O. Ludwigsen, Cayla Jewett, Matthew Jusczcyk

Daniel Ludwigsen

Students encounter cavity resonance and waveguide phenomena in acoustics courses and texts, where the study is usually limited to cases with simple geometries: parallelepipeds, cylinders, and spheres. Long-wavelength approximations help with situations of more complexity, as in the classic Helmholtz resonator. At Kettering University, we are beginning to employ finite element modeling in our acoustics classes to help undergraduates better understand the acoustic modes of actual structures. This approach to the time-independent wave equation (the Helmholtz equation) was first used in a research and measurements class to investigate two classic resonance problems. The first problem was a study of resonance …

Acoustic Testing And Modeling: An Advanced Undergraduate Laboratory, Daniel A. Russell, Daniel O. Ludwigsen

Daniel Ludwigsen

This paper describes an advanced laboratory course in acoustics, specifically targeted for students with an interest in engineering applications at a school with a strongly integrated industrial co-op program. The laboratory course is developed around a three-pronged approach to problem solving that combines and integrates theoretical models, computational models, and experimental data. The course is structured around modules that begin with fundamental concepts and build laboratory skills and expand the knowledge base toward a final project. Students keep a detailed laboratory notebook, write research papers in teams, and must pass laboratory certification exams. This paper describes the course layout and …

Optimizing Compressed Air Storage For Energy Efficiency, Brian Abels, J. Kelly Kissock

J. Kelly Kissock

Compressed air storage is an important, but often misunderstood, component of compressed air systems. This paper discusses methods to properly size compressed air storage in load-unload systems to avoid short cycling and reduce system energy use. First, key equations relating storage, pressure, and compressed air flow are derived using fundamental thermodynamic relations. Next, these relations are used to calculate the relation between volume of storage and cycle time in load-unload compressors. It is shown that cycle time is minimized when compressed air demand is 50% of compressor capacity. The effect of pressure drop between compressor system and storage on cycle …

Lean Energy Analysis: Identifying, Discovering And Tracking Energy Savings Potential, J. Kelly Kissock, John Seryak

J. Kelly Kissock

Energy in manufacturing facilities is used for direct production of goods, space conditioning, and general facility support such as lighting. This paper presents a methodology, called lean energy analysis, LEA, for graphically and statistically analyzing plant energy use in terms of these major end uses.

The LEA methodology uses as few as 60 easily obtainable data points. Multivariable change-point models of electricity and natural gas use as functions of outdoor air temperature and production data are developed. The statistical models are used to subdivide plant energy use into facility, space-conditioning and production-related components.

These breakdowns suggest the savings potential from …

Energy Efficient Process Heating: Insulation And Thermal Mass, Kevin Carpenter, J. Kelly Kissock

J. Kelly Kissock

Open tanks and exterior surfaces of process heating equipment lose heat to the surroundings via convection, radiation, and/or evaporation. A practical way of reducing heat loss is by insulating or covering the surfaces. This paper presents methods to quantify heat loss and energy savings from insulating hot surfaces and open tanks. The methods include radiation and evaporation losses, which are ignored by simplified methods. In addition, thermal mass, such as refractory, conveyor and racking equipment, acts as a heat sink and increases heating energy use in process heating applications. This paper presents lumped capacitance and finite-difference methods for estimating heat …

Improving Compressed Air Energy Efficiency In Automotive Plants: Practical Examples And Implementation, Nasr Alkadi, J. Kelly Kissock

J. Kelly Kissock

The automotive industry is the largest industry in the United States in terms of the dollar value of production [1]. U.S. automakers face tremendous pressure from foreign competitors, which have an increasing manufacturing presence in this country. The Big Three North American Original Equipment Manufacturers (OEMs)-General Motors, Ford, and Chrysler-are reacting to declining sales figures and economic strain by working more efficiently and seeking out opportunities to reduce production costs without negatively affecting the production volume or the quality of the product. Successful, cost-effective investment and implementation of the energy efficiency technologies and practices meet the challenge of maintaining the …

Energy Efficient Process Heating: Managing Air Flow, Kevin Carpenter, J. Kelly Kissock

J. Kelly Kissock

Much energy is lost through excess air flow in and out of process heating equipment. Energy saving opportunities from managing air flow include minimizing combustion air, preheating combustion air, minimizing ventilation air, and reconfiguring openings to reduce leakage.

This paper identifies these opportunities and presents methods to quantify potential energy savings from implementing these energy-savings measures. Case study examples are used to demonstrate the methods and the potential energy savings.The method for calculating savings from minimizing combustion air accounts for improvement in efficiency from increased combustion temperature and decreased combustion gas mass flow rate.

The method for calculating savings from …

Measuring Plant-Wide Energy Savings, J. Kelly Kissock, Carl Eger

J. Kelly Kissock

This paper presents a general method for measuring plant-wide industrial energy savings and demonstrates the method using a case study from an actual industrial energy assessment. The method uses regression models to characterize baseline energy use. It takes into account changes in weather and production, and can use sub-metered data or whole plant utility billing data. In addition to calculating overall savings, the method is also able to disaggregate savings into components, which provides additional insight into the effectiveness of the individual savings measures. Although the method incorporates search techniques and multi-variable least-squares regression, it is easily implemented using data …

Oscillations Of Biomimetic Scales Elastica, Hessein Ali

Hessein Ali

Simulation Model Of An Automatic Commercial Ice Machine, Haithem Murgham, David Myszka, Vijay Bahel, Rajan Rajendran, Kurt Knapke, Suresh Shivashankar, Kyaw Wynn

David Myszka

Automatic commercial ice-making machines that produce a batch of cube ice at regular intervals are known as “cubers." Such machines are commonly used in food service, food preservation, hotel, and health service industries. The machines are typically rated for the weight of ice produced over a 24-hour period at ambient air temperatures of 90°F and water inlet temperature of 70°F.

These cubers typically utilize an air-cooled, vapor-compression cycle to freeze circulating water flowing over an evaporator grid. Once a sufficient amount ice is formed, a valve switches to enable a harvest mode, where the compressor’s discharge gas is routed into …

Peridynamic Modeling Of Ruptures In Biomembranes, Michael Taylor, Irep Gözen, Samir Patel, Aldo Jesorka, Katia Bertoldi

Michael Taylor

We simulate the formation of spontaneous ruptures in supported phospholipid double bilayer membranes, using peridynamic modeling. Experiments performed on spreading double bilayers typically show two distinct kinds of ruptures, floral and fractal, which form spontaneously in the distal (upper) bilayer at late stages of double bilayer formation on high energy substrates. It is, however, currently unresolved which factors govern the occurrence of either rupture type. Variations in the distance between the two bilayers, and the occurrence of interconnections (“pinning sites”) are suspected of contributing to the process. Our new simulations indicate that the pinned regions which form, presumably due to …

Multi-Disciplinary Hands-On Desktop Learning Modules And Modern Pedagogies, Bernard J. Van Wie, David B. Thiessen, Marc Compere, Ximena Toro, Jennifer C. Adam, Et Al.

Marc Compere

Our team’s research focuses on fundamental problems in undergraduate education in terms of how to expand use of well researched, yet still “new”, teaching pedagogies of ‘sensing’ or ‘hands-on’, ‘active’ and ‘problem-based learning’ within engineering courses. It is now widely accepted that traditional lectures ARE NOT best for students – yet that is what the community almost universally does. To address this issue we are developing new Desktop Learning Modules (DLMs) that contain miniaturized processes with a uniquely expandable electronic system to contend with known sensor systems/removable cartridges, as well as, unknown expansions to the project. We have shown that …

Project Haiti 2012: Providing An Experiential Learning Experience Through The Design And Delivery Of A Water Purifier In Haiti, Yung Wong, Johnathon Camp, Shavin Pinto, Kyle Fennesy, Marc Compere, Yan Tang

Marc Compere

In this paper, we share our experiences and lessons learned from Project Haiti 2012, a project to design and install a water purification system serving 20,000 people per day in the largest tent city in Haiti. Project Haiti 2012 was the third and largest system we have built for Haitians and represents a huge success for all participants and stakeholders. This paper discusses the unique experiential learning opportunity involved in the design and delivery of the water purifier in a foreign developing country. Multiple positive educational, social, and economic outcomes were achieved including students applying knowledge gained from coursework towards …

High Tech High Touch: Lessons Learned From Project Haiti 2011, Yan Tang, Marc Compere, Yung Lun Wong, Jared Anthony Coleman, Matthew Charles Selkirk

Marc Compere

In this paper, we will share our experiences and lessons learned from a design project for providing clean water to a Haitian orphanage (Project Haiti 2011). Supported by funds from a renewable energy company and the university president’s office, five engineering students and two faculty members from Embry-Riddle Aeronautical University successfully designed and installed a solar powered water purification system for an orphanage located in Chambellan, Haiti. This paper discusses the unique educational experiences gained from unusual design constraints, such as ambiguity of existing facilities due to limited communication, logistics of international construction at a remote village location, and cross-cultural …

How To Establish Successful Cooperative Student Learning Centers For Stem Courses, Ronald James Bieniek, Douglas R. Carroll, Cesar Mendoza, Oran Allan Pringle, Ekkehard Sinn, Kai-Tak Wan, Donald C. Wunsch

Oran Pringle

Students learn more if they are actively involved in the learning process, particularly in a cooperative manner. Several UMR faculty have operated course-based learning centers (LCs) as part of the campus-wide Learning Enhancement Across Disciplines (LEAD) Program of student learning assistance and enhancement. LCs are designed to assist large numbers of students in a cost- and time-efficient manner that promotes student engagement without requiring undue amounts of faculty time. Course instructors spend time in the open learning environment of the LC, in lieu of office hours, guiding students to master course material and skills in their evolution from novice to …

U.S. Billion-Ton Update: Biomass Supply For A Bioenergy And Bioproducts Industry, Robert D. Perlack, Laurence M. Eaton, Anthony F. Turhollow Jr., Matt H. Langholtz, Craig C. Brandt, Mark E. Downing, Robin L. Graham, Lynn L. Wright, Jacob M. Kavkewitz, Anna M. Shamey, Richard G. Nelson, Bryce J. Stokes, William L. Rooney, David J. Muth Jr., J. Richard Hess, Jared M. Abodeely, Chad Hellwinckel, Danial De La Torre Ugarte, Daniel C. Yoder, James P. Lyon, Timothy G. Rials, Timothy A. Volk, Thomas S. Buchholz, Lawrence P. Abrahamson, Robert P. Anex, Thomas B. Voigt, William Berguson, Don E. Riemenschneider, Douglas Karlen, Jane M. F. Johnson, Robert B. Mitchell, Kenneth P. Vogel, Edward P. Richard Jr., John Tatarko, Larry E. Wagner, Kenneth E. Skog, Patricia K. Lebow, Dennis P. Dykstra, Marilyn A. Buford, Patrick D. Miles, D. Andrew Scott, James H. Perdue, Robert B. Rummer, Jamie Barbour, John A. Stanturf, David B. Mckeever, Ronald S. Zalesny Jr., Edmund A. Gee, P. Daniel Cassidy, David Lightle

Douglas L Karlen

The Report, Biomass as Feedstock for a Bioenergy and Bioproducts Industry: The Technical Feasibility of a Billion-Ton Annual Supply (generally referred to as the Billion-Ton Study or 2005 BTS), was an estimate of “potential” biomass within the contiguous United States based on numerous assumptions about current and future inventory and production capacity, availability, and technology. In the 2005 BTS, a strategic analysis was undertaken to determine if U.S. agriculture and forest resources have the capability to potentially produce at least one billion dry tons of biomass annually, in a sustainable manner—enough to displace approximately 30% of the country’s present petroleum …

Interference-Free Gas-Phase Thermometry At Elevated Pressure Using Hybrid Femtosecond/Picosecond Rotational Coherent Anti- Stokes Raman Scattering, Joseph D. Miller, Chloe Elizabeth Dedic, Sukesh Roy, James R. Gord, Terrence R. Meyer

Terrence R Meyer

Rotational-level-dependent dephasing rates and nonresonant background can lead to significant uncertainties in coherent anti-Stokes Raman scattering (CARS) thermometry under high-pressure, lowtemperature conditions if the gas composition is unknown. Hybrid femtosecond/picosecond rotational CARS is employed to minimize or eliminate the influence of collisions and nonresonant background for accurate, frequency-domain thermometry at elevated pressure. The ability to ignore these interferences and achieve thermometric errors of <5% is demonstrated for N2 and O2 at pressures up to 15 atm. Beyond 15 atm, the effects of collisions cannot be ignored but can be minimized using a short probe delay (~6.5 ps) after Raman excitation, …

Fast-Framing Ballistic Imaging Of Velocity In An Aerated Spray, David Sedarsky, James Gord, Campbell Carter, Terrence R. Meyer, Mark Linne

Terrence R Meyer

We describe further development of ballistic imaging adapted for the liquid core of an atomizing spray. To fully understand spray breakup dynamics, one must measure the velocity and acceleration vectors that describe the forces active in primary breakup. This information is inaccessible to most optical diagnostics, as the signal is occluded by strong scattering in the medium. Ballistic imaging mitigates this scattering noise, resolving clean shadowgram-type images of structures within the dense spray region. We demonstrate that velocity data can be extracted from ballistic images of a spray relevant to fuel-injection applications, by implementing a simple, targeted correlation method for …

A High-Speed X-Ray Detector System For Noninvasive Fluid Flow Measurements, Timothy B. Morgan, Benjamin R. Halls, Terrence R. Meyer, Theodore J. Heindel

Terrence R Meyer

The opaque nature of many multiphase flows has long posed a significant challenge to the visualization and measurement of desired characteristics. To overcome this difficulty, X-ray imaging, both in the form of radiography and computed tomography, has been used successfully to quantify various multiphase flow phenomena. However, the relatively low temporal resolution of typical X-ray systems limit their use to moderately slow flows and time-average values. This paper discusses the development of an X-ray detection system capable of high-speed radiographic imaging that can be used to visualize multiphase flows. Details of the hardware will be given and then applied to …