Open Access. Powered by Scholars. Published by Universities.®

Mechanical Engineering Commons

Open Access. Powered by Scholars. Published by Universities.®

Articles 1 - 9 of 9

Full-Text Articles in Mechanical Engineering

Influence Of Naoh Concentration On Transfer Process Of Graphene, Francisco Saldana, Chengyu Wen, George Patrick Watson Sep 2019

Influence Of Naoh Concentration On Transfer Process Of Graphene, Francisco Saldana, Chengyu Wen, George Patrick Watson

Protocols and Reports

The process of transferring a monolayer of graphene using two different concentrations of sodium hydroxide (NaOH) solution unto a silicon dioxide (SiO2) coated Si chip using electrochemistry was performed. The transfer process is crucial for the delamination of a continuous graphene monolayer film from copper foil. After examining and inspecting the integrity of the graphene monolayer, it was observed that the lower concentration to NaOH led to slower rate of hydrogen bubble generation; this condition was found to be less destructive and yielded a graphene film with fewer visible tears.


Experimental And Theoretical Evaluation Of The Effect Of Panel Geometry On The Failure Of Corrugated Board Panel, Takashi Takayama, Katsuhiko Saito, Akira Higashiyama Jun 2019

Experimental And Theoretical Evaluation Of The Effect Of Panel Geometry On The Failure Of Corrugated Board Panel, Takashi Takayama, Katsuhiko Saito, Akira Higashiyama

Journal of Applied Packaging Research

McKee’s formula is widely used to predict the compression strength (CS) of corrugated boxes and panels. It can accurately estimate the compression strength of boxes that are within a practical size range, but recently, larger and smaller corrugated boxes than before have been extensively developed. Therefore, there is a need for a CS prediction formula that works beyond the application range of McKee’s formula. Recent researches consider the failure mode as a combination of collapsing and buckling failure and remove the constraints and the assumptions associated with McKee’s formula. This makes it possible to more accurately estimate ...


Fracture Toughness Improvement Of ����� Ceramics By Grain Size Control And Ductile Phase Reinforcement, Kesong Wang May 2019

Fracture Toughness Improvement Of ����� Ceramics By Grain Size Control And Ductile Phase Reinforcement, Kesong Wang

Engineering and Applied Science Theses & Dissertations

This study used grain size control and ductile phase reinforcement to improve fracture toughness of ����� ceramics. Alpha alumina particles of 100 nm, 0.5-1 micrometers, and 10 micrometers were coated with 1-5 nm nickel by electroless nickel plating (ENP). The coated powders were consolidated at 1200℃-1500℃ by spark plasma sintering (SPS). The sintered samples were annealed at 1100 oC for 1.5 hours and 10 hours to determine the effect of post sintering annealing on hardness and fracture toughness. Density of the samples were measured by the standard Archimedes method using a 5 mL pycnometer. Hardness values were determined ...


A Study On Ultrasonic Energy Assisted Metal Processing : Its Correeltion With Microstructure And Properties, And Its Application To Additive Manufacturing., Anagh Deshpande May 2019

A Study On Ultrasonic Energy Assisted Metal Processing : Its Correeltion With Microstructure And Properties, And Its Application To Additive Manufacturing., Anagh Deshpande

Electronic Theses and Dissertations

Additive manufacturing or 3d printing is the process of constructing a 3-dimensional object layer-by-layer. This additive approach to manufacturing has enabled fabrication of complex components directly from a computer model (or a CAD model). The process has now matured from its earlier version of being a rapid prototyping tool to a technology that can fabricate service-ready components. Development of low-cost polymer additive manufacturing printers enabled by open source Fused Deposition Modeling (FDM) printers and printers of other technologies like SLA and binder jetting has made polymer additive manufacturing accessible and affordable. But the metal additive manufacturing technologies are still expensive ...


Additive Manufacturing Of High Performance Flexible Thermoelectric Generators Using Nanoparticle Inks, Tony Valayil Varghese May 2019

Additive Manufacturing Of High Performance Flexible Thermoelectric Generators Using Nanoparticle Inks, Tony Valayil Varghese

Boise State University Theses and Dissertations

Flexible thermoelectric devices are attractive power sources for the growing demand of flexible electronics and sensors. Thermoelectric generators have an advantage due to no moving parts, silent operation and constant power production with a thermal gradient.

Conventional thermoelectric devices are rigid and fabricated using complex and relatively costly manufacturing processes, presenting a barrier to increase the market share of this technology. To overcome such barriers, this work focuses on developing near ambient-temperature flexible thermoelectric generators using relatively low-cost additive manufacturing processes. A screen printable ink was developed for transforming nanoparticle ink into high-performance flexible thermoelectric generators with a peak thermoelectric ...


The Influence Of Asphalt Ageing On Induction Healing Effect On Porous Asphalt Concrete, Shi Xu, Xueyan Liu, Amir Tabakovic, Erik Schlangen Feb 2019

The Influence Of Asphalt Ageing On Induction Healing Effect On Porous Asphalt Concrete, Shi Xu, Xueyan Liu, Amir Tabakovic, Erik Schlangen

Articles

Induction healing is a proven technology which is able to improve the self‐healing capacity of asphalt concrete. Healing is achieved via electromagnetic current produced by passing induction machine, where steel asphalt constituents heat up which in turn soften the bitumen in the asphalt layer, allowing it to flow and close cracks, repairing the damage. This paper reports on the study which investigated the influence of ageing on the healing capacity of Porous Asphalt (PA) concrete. Porous Asphalt concrete mix was prepared first, then subjected to an accelerated (laboratory) ageing process using a ventilated oven. In order to further evaluate ...


Mechanical Performance Of Structural Systems With Missing Members: From Buildings To Architected Materials, Panagiotis Pantidis Jan 2019

Mechanical Performance Of Structural Systems With Missing Members: From Buildings To Architected Materials, Panagiotis Pantidis

Doctoral Dissertations

Structural systems are potentially subjected to damage initiating scenarios throughout the course of their service time. Depending on the nature and extent of the damaging event, they may experience significant reduction or even complete loss of their mechanical performance. This dissertation delves into the mechanics of structural systems under the notion of missing members from their domain, investigating types of structural systems: a) multi-story steel framed buildings, and b) materials with a truss-lattice microstructure.

Part I of the dissertation investigates the performance of multi-story steel framed buildings under a column removal scenario, developing an analytical framework for their quasi-static robustness ...


Autojack - Hydraulic Powertrain System, Tyce Vu Jan 2019

Autojack - Hydraulic Powertrain System, Tyce Vu

All Undergraduate Projects

A primary problem for mechanics and automotive enthusiasts is the risk associated with lifting and securing a vehicle with conventional jack stands. Often times, improper jack-stand installation results in the vehicle collapsing unexpectedly, causing injury and/or death. This problem can be minimized through the application of a newly re-designed vehicle lifting system. The conventional method for lifting cars is time consuming and can be unsafe in many circumstances. A better, safer, and more efficient lift design was needed; the AutoJack. The approach of the AutoJack design was entirely focused on the safety of lifting a vehicle. Safety was improved ...


Carbon Fiber Monocoque, Dan Brown, Leland Hoffman Jan 2019

Carbon Fiber Monocoque, Dan Brown, Leland Hoffman

Williams Honors College, Honors Research Projects

The University of Akron’s Human Powered Vehicle Team designed a high performing, fully functioning vehicle that is safe, efficient, and practical for the 2018-2019 season. These objectives were the main priorities when it came to the initial stages of designing the vehicle. In addition, the vehicle was designed in accordance with the ASME 2019 Human Powered Vehicle Challenge guidelines to satisfy all the rules and requirements. Additional priorities have been created to teach practical engineering skills and techniques to the students participating in the project through different points in the production process including research, vehicle design, construction, and testing ...