Mechanical Engineering Commons^™

Solar Photovoltaic Performance Monitoring: A Bibliometric Review, Research Gaps And Opportunities, Javed Sayyad, Paresh Nasikkar

Library Philosophy and Practice (e-journal)

Electrical power generation has been revolutionized by growing demand and use of Renewable Energy (RE) sources such as Solar Photovoltaic (SPV) as the main electricity source in modern times. The main objective of this bibliometric analysis is to understand the scope of the literature available for SPV performance characterization. This detailed reviewed was performed on the documents related to SPV research considering all the subject categories from Scopus and Web of Science (WoS) databases. The patterns for the particular set of keywords were broke down with the recuperated outcomes from Scopus database in the language, publication type, year of publication, …

Parametric Study Of Residual Stresses In Wire And Arc Additive Manufactured Parts, Hisham Khaled Jamil Abusalma

Mechanical & Aerospace Engineering Theses & Dissertations

Wire and Arc Additive Manufacturing (WAAM) is a cost-effective additive manufacturing process due to its capability to fabricate large metal parts with high deposition rate and low equipment cost. Although this method is gaining popularity in manufacturing industry, more research is needed to understand process parameters’ effects on residual stress (RS) distribution and part distortion. As such, a 3D thermo-elastic-plastic transient model was established in ABAQUS and employed to investigate the effect of process parameters such as the torch speed, the deposition power and the interlayer dwell time on RS distribution and distortion in WAAM part. The numerical model utilized …

Improvement Of Light Intensity And Efficiency Of N-Zno/Nio/P-Gan Heterojunction-Based White Light Emitting Diodes Using Micro-/Nanolens Array, Apurba Adhikary, Md Shamim Ahsan, Md Mahbub Hossain, Md Bipul Hossain, S. H. Shah Newaz, Farid Ahmed, Ik-Bu Sohn

Manufacturing & Industrial Engineering Faculty Publications and Presentations

Our study proposes a technique to enhance light extraction efficiency of light emitting diodes (LEDs) by incorporating various micro-/nanolens arrays (MNLAs) on the substrate layer, which in turn increases the external quantum efficiency (EQE) of the LEDs. To simulate the LEDs, we utilized the finite difference time domain method. To achieve a white LED, we inserted a thin layer of NiO at the interface between the n-type ZnO and the p-type GaN. The basic n-ZnO/NiO/p-GaN heterojunction-based LED exhibited an EQE of 10.99% where the effective refractive index of the LED structure was 1.48. The EQE was further increased by engraving …

Grow Local Manufacturing Along Us/Mexico Border Region For An Integrated Supply Chain In The Post Covid-19 Era, Jianzhi Li

Manufacturing & Industrial Engineering Faculty Publications and Presentations

The current coronavirus disease pandemic, plus the strong movement of manufacturing reshoring, provide a unique opportunity for many US regions to grow local manufacturers. This technical note attempts to review the current situation and trend in US manufacturing. We then discuss challenges and necessary steps, such as asset mapping, required to grow local suppliers. Suggestions are then made to support growing local suppliers along the US/Mexico border region.

Evaluation Of A Bulge Reduction Technology For Corrugated Fiberboard Containers Under Static Compression, Daan Peleman, Jay Singh, Koushik Saha, S. Roy

Journal of Applied Packaging Research

This research examines the effect of top-to-bottom static compression load on the bulge of RSC containers. The study compares a control regular slotted container (RSC) constructed with corrugated fiberboard to tape-reinforced designs. The bulge reduction, achieved using various tape placements and conditioning environments, were measured. Currently, no research on the effect of reinforcement tape towards reduction in the out-of-plane displacement (bulging) of the corrugated fiberboard panels has been undertaken. Samples related to four different container designs, varying by presence, quantity and the position of the reinforcement tape on the vertical panels, were tested and analyzed. The study involved the use …

Characterization And Performance Of Minimum Quantity Lubricants In Through-Tool Drilling, Amla Patil, Jay Raval, Tim Bangma, Immanuel Edinbarough, Bruce Tai, David Stephenson, Suleiman Obeidat, Wayne Nguyen Hung

Manufacturing & Industrial Engineering Faculty Publications and Presentations

This study characterized airborne microdroplet diameters and size distribution from two commercially available lubricants A and B for internal minimum quantity lubrication (MQL). The effects of air pressure, oil channel size, physical properties of lubricants on the resultant microdroplets and through-tool MQL drilling performance were studied. Airborne microdroplet diameters were highly sensitive to the coolant channel sizes and air pressure. Cluster method was used to divide microdroplets into smaller clusters for comparison. Experimental data show that the average airborne microdroplet of lubricant B was larger than that of lubricant A at different air pressures and channel sizes. The contact angle …

Sustainable Smouldering For Waste-To-Energy: Scale, Heat Losses, And Energy Efficiency, Tarek L. Rashwan

Electronic Thesis and Dissertation Repository

Applied smouldering combustion is emerging as a highly energy efficient approach towards waste-to-energy. This thesis aims to better understand this potential by addressing a critical knowledge gap between laboratory scale smouldering research and large-scale applications. Altogether, new understanding in provided on the complex and dynamic interactions between the reaction zone (smouldering front) and the cooling zone (treated inert porous media) by integrating theory, experiments, analytical modelling, and global energy balance calculations. The experiments spanned a range of reactor sizes and smouldering conditions (from weak to robust) with dry (carbon) and wet (sludge) fuels mixed in sand. This work revealed that …

Robust And Sustainable Energy Pathways To Reach Mexico’S Climate Goals, Rodrigo Mercado Fernandez

Doctoral Dissertations

As countries set climate change goals for adaptation and mitigation efforts, there are many questions regarding to how to reach these targets. These efforts will necessitate the transition of our electricity infrastructure from relying on conventional electricity generation technologies including natural gas, coal and oil, to clean energy generation with renewables. Through the three essays presented in this dissertation, we explore various pathways of development for the electricity system to reach long term climate change goals. We are interested in identifying: Is there a unique optimal development option or are there various? How do different mixes of electricity generation technologies …

Application Of Optimized Laser Surface Re-Melting Process On Selective Laser Melted 316l Stainless Steel Inclined Parts, Jafar Ghorbani, Jianzhi Li, Anil K. Srivastava

Manufacturing & Industrial Engineering Faculty Publications and Presentations

Lower surface quality of selective laser melting (SLM) manufactured parts remains to be a key shortcoming particularly for high performance functional components. In this paper, the authors utilized Box–Behnken methodology to explore the effect of laser surface re-melting process parameters. The process parameters are:laser power, laser exposure time, laser point distance, and shell layer thickness. The experiments were conducted using Renishaw AM-250 machine. SLM manufactured parts with inclination of 45˚ up-skin were treated with a given surface roughness using laser surface re-melting (LSR). The optimization of process parameters was conducted using response surface methodology and the validation tests was carried …

Modeling Of Electrical Grid Systems To Evaluate Sustainable Electricity Generation In Pakistan, Muhammad Mustafa Amjad

Masters Theses

Pakistan has always had a history of severe energy shortfalls, which rose up to an alarming 33% in 2013. This situation was countered by investments in the energy sector through the China Pakistan Economic Corridor (CPEC), which were unfortunately largely based on brown fuels. Although beneficial in the short term, these investments do not bode well for the climate scenario of Pakistan, with various parts of the country already having experienced temperatures rise of 1-3°C. To ensure that the current situation doesn’t exacerbate and is tackled in a timely manner, this research aims to examine how the untapped potential of …

Structural Health Monitoring Of Pipelines In Radioactive Environments Through Acoustic Sensing And Machine Learning, Michael Thompson

FIU Electronic Theses and Dissertations

Structural health monitoring (SHM) comprises multiple methodologies for the detection and characterization of stress, damage, and aberrations in engineering structures and equipment. Although, standard commercial engineering operations may freely adopt new technology into everyday operations, the nuclear industry is slowed down by tight governmental regulations and extremely harsh environments. This work aims to investigate and evaluate different sensor systems for real-time structural health monitoring of piping systems and develop a novel machine learning model to detect anomalies from the sensor data. The novelty of the current work lies in the development of an LSTM-autoencoder neural network to automate anomaly detection …

Towards A Cyber-Physical Manufacturing Cloud Through Operable Digital Twins And Virtual Production Lines, Md Rakib Shahriar

Graduate Theses and Dissertations

In last decade, the paradigm of Cyber-Physical Systems (CPS) has integrated industrial manufacturing systems with Cloud Computing technologies for Cloud Manufacturing. Up to 2015, there were many CPS-based manufacturing systems that collected real-time machining data to perform remote monitoring, prognostics and health management, and predictive maintenance. However, these CPS-integrated and network ready machines were not directly connected to the elements of Cloud Manufacturing and required human-in-the-loop. Addressing this gap, we introduced a new paradigm of Cyber-Physical Manufacturing Cloud (CPMC) that bridges a gap between physical machines and virtual space in 2017. CPMC virtualizes machine tools in cloud through web services …

Embedding Computer Simulation Based Classroom Activities To Enhance The Learning Experience For Manufacturing Systems, Tzu-Liang Bill Tseng, Md Fashiar Rahman, Richard Chiou, Ivan Arturo Renteria-Marquez, Aditya Akundi, Amit J. Lopes, Jeevarathinam Senthilkumar

Manufacturing & Industrial Engineering Faculty Publications and Presentations

In recent time, manufacturing environment are bracing higher end technologies to achieve high productivity, efficiency and effectiveness. Due to the adoption of the sophisticated technologies, the system is becoming very complex and stochastic. Moreover, the manufacturing system is interconnected among its different subsystems and components, which cannot be described only through the theoretical explanation. Here, computer simulation can be integrated to design and visualize the stochastic and complex system. This paper uses the advantage of simulation to describe a series classroom activity using SIMIO software, which are deployed in industrial systems simulation course in the University of Texas at El …

Thermal Conductivity Performance Of 2d Hbn/Mos 2/Hybrid Nanostructures Used On Natural And Synthetic Esters, Jaime Taha-Tijerina, Hélio Ribeiro, Karla Aviña, Juan Manuel Martínez, Anna Paula Godoy, Josué Marciano De Oliveira Cremonezzi, Milene Adriane Luciano, Marcos Antônio Gimenes Benega, Ricardo Jorge Espanhol Andrade, Guilhermino José Macedo Fechine

Manufacturing & Industrial Engineering Faculty Publications and Presentations

In this paper, the thermal conductivity behavior of synthetic and natural esters reinforced with 2D nanostructures-single hexagonal boron nitride (h-BN), single molybdenum disulfide (MoS2), and hybrid h-BN/MOS2-were studied and compared to each other. As a basis for the synthesis of nanofluids, three biodegradable insulating lubricants were used: FR3TM and VG-100 were used as natural esters and MIDEL 7131 as a synthetic ester. Two-dimensional nanosheets of h-BN, MoS2, and their hybrid nanofillers (50/50 ratio percent) were incorporated into matrix lubricants without surfactants or additives. Nanofluids were prepared at 0.01, 0.05, 0.10, 0.15, and 0.25 weight percent of filler fraction. The experimental …

Development Of Water Coning Control Design Metrics In Naturally Fractured Reservoirs, Samir Prasun

LSU Doctoral Dissertations

Naturally fractured reservoirs (NFRs) with bottom-water are known for their instant water breakthrough and severe water coning that reduces oil recovery. This is because water channels through the highly permeable fractures easily connecting the well to the aquifer bypassing the oil contained in the matrix. Remedial techniques such as producing below critical-oil rate, optimizing the well spacing and installing the downhole water sink (DWS)/ downhole water loop (DWL) technology, have already been successfully tested in single-porosity reservoirs (SPR). However, applicability of these techniques in NFRs are unknown since only a few studies have been performed on their feasibility in NFRs, …

Feasibility Of Electric Field Assisted Clogging Reduction In Cold Gas Spraying Nozzle, Hendric Tronsson

ENGS 88 Honors Thesis (AB Students)

The relatively novel cold spraying process expands its range of applications constantly. In order to continue this trend, this process still has various hurdles that need to be overcome such as clogging. Clogging within the cold gas spraying process causes porous coatings with less material properties and lower durability; a solution is needed in order to reduce the clogging and so expand the cold gas spraying applications. This study aimed to explore the feasibility of using an electric field to reduce clogging. To do so a simplified channel was used to simulate charged particle trajectory shifts under the influence of …

Virginia Digital Shipbuilding Program (Vdsp): Building An Agile Modern Workforce To Improve Performance In The Shipbuilding And Ship Repair Industry, Joseph Peter Kosteczko, Katherine Smith, Jessica Johnson, Rafael Diaz

VMASC Publications

Industry 4.0 is the latest stage in the Industrial Revolution and is reflected in the digital transformation and use of emergent technologies including the Internet of Things, Big Data, Robotic automation of processes, 3D printing and additive manufacturing, drones and Artificial Intelligence (AI) in the manufacturing industry. The implementation of these technologies in the Shipbuilding and Ship Repair Industry is currently in a nascent stage. Considering this, there is huge potential to increase cost savings, decrease production timelines, and drive down inefficiencies in Lifecyle management of ships. However, the implementation of these Industry 4.0 technologies is hindered by a noticeable …

Smart Environments For Assisted Living: A Multidisciplinary Collaboration In Engineering And Architecture Education, Adriana Rios-Santiago, Anabel Pineda-Briseno, Jesus A. Gonzalez-Rodriguez, Uriel Saul Huerta

Manufacturing & Industrial Engineering Faculty Publications and Presentations

This paper presents a description of a collaborative project based on the integration of technology development in the built environment for assisted living. The multidisciplinary collaboration is developed as a cooperative commitment to provide support for cross-border, collective projects. It was initiated as a project-based learning setting between undergraduate engineering students, and four years later the program shifted to include undergraduate architecture students and engineering master’s students. The learning experience opens the gate to a completely new collaborative setting, yet to be established, independent from its predecessor setting of project-based learning, focusing now towards an interdisciplinarity setting in cross-border collaboration. …

Rapid Manufacturing Of Critical Industrial Parts: A Method Based On Reverse Engineering, Rapid Prototyping, And Coordinate Metrology, Immanuel Edinbarough, Aditya Akundi

Manufacturing & Industrial Engineering Faculty Publications and Presentations

This paper presents a method of rapidly manufacturing industrial parts that are critical to the production. In order to assist the Advanced Manufacturing industry, a senior project team at the University of Texas Rio Grande Valley (UTRGV) applied Rapid Manufacturing (RM) to manufacture or fabricate critical machine parts used to maintain production machines. Failures of parts and tools in industrial settings cost money and hurt output. Usually, the problem arises when the tooling being used is one of a kind and repair or replacements come with long leadtimes. Other problems are encountered when original part or tool engineering drawing is …

Text Mining-Based Qualitative Student Assessment Of Interactive Simulation Learning Using Simio Tool – A Work In Progress, Aditya Akundi, Immanuel Edinbarough

Manufacturing & Industrial Engineering Faculty Publications and Presentations

Computer simulations complement and extend the real-world components of industries and manufacturing organizations. Teaching simulation-based tools helps students in modeling and analyzing the behavior of real time systems. With the increased demand observed in products and technology consumption, manufacturing industries are evolving to embrace new technologies and initiatives. To keep the emerging workforce technically competent in current tools to understand and interpret manufacturing processes, this paper portrays an effort by the authors in introducing SIMIO i.e. a tool on Simulation of intelligent objects to undergraduate students at University of Texas Rio Grande Valley and in understanding the influence of using …

Expanding Engineering And Technology Opportunities To Students In The Border Region Through International Collaboration, Jesus A. Gonzalez-Rodriguez, Immanuel Edinbarough, Adriana Rios-Santiago, Anabel Pineda-Briseno

Manufacturing & Industrial Engineering Faculty Publications and Presentations

Expanding Engineering and Technology Opportunities to Students in the Border Region through International Collaboration

For some years now, our Department of Engineering Technology of the XXXX, has collaborated with Universities across the southern border to carry out different activities such as undergraduate research, collaborative course-based projects, and senior design projects. We have observed how students benefit from being exposed to work in multidisciplinary and multicultural teams.

We now expand this form of work to a higher-level research collaboration where students and faculty from four different institutions participate. Two institutions of higher education in Mexico and a University and a Community …

Hollow-Core Photonic Crystal Fiber Mach–Zehnder Interferometer For Gas Sensing, Kaveh Nazeri, Farid Ahmed, Vahid Ahsani, Hang-Eun Joe, Colin Bradley, Ehsan Toyserkani, Martin B. G. Jun

Manufacturing & Industrial Engineering Faculty Publications and Presentations

A novel and compact interferometric refractive index (RI) point sensor is developed using hollow-core photonic crystal fiber (HC-PCF) and experimentally demonstrated for high sensitivity detection and measurement of pure gases. To construct the device, the sensing element fiber (HC-PCF) was placed between two single-mode fibers with airgaps at each side. Great measurement repeatability was shown in the cyclic test for the detection of various gases. The RI sensitivity of 4629 nm/RIU was demonstrated in the RI range of 1.0000347–1.000436 for the sensor with an HC-PCF length of 3.3 mm. The sensitivity of the proposed Mach–Zehnder interferometer (MZI) sensor increases when …

Designing An Adjustable And Transportable Staircase, Allison Currey

Undergraduate Honors Thesis Projects

People climb stairs every day, whether it is at work, a store, or at home; however, there are populations such as people who are elderly, with pathologies, with Parkinson’s disease, or have suffered from a stroke that see climbing the stairs as a challenging task and it decreases their mobility and quality of life. Factors such as muscle weakness, strategy, and balance have been previously investigated in these populations during stair climbing. However, few studies have researched how stair climb ability, balance, and perception of difficulty are influenced by step height. The objective of this thesis is to design a …

Aerial Screw Vtol Rotorcraft, Macale Rielly, Alexa Culp, Thomas Osteen, Adeline Perry

Senior Design Project For Engineers

Known as the “Renaissance Man,” DaVinci’s impressive knowledge of mechanics and inventive prowess would influence engineers and innovators hundreds of years later to make human flight a reality. However, due to the limited capacity of engineering and manufacturing at the time, his invention had been shallowly investigated in a production setting. This project strove to properly acknowledge DaVinci’s invention by thorough examination and critical analysis of his concept with the hopes of gaining a better understanding of why it is considered the “foundation of vertical flight”.

An iterative design approach was employed, utilizing faculty and university resources, team knowledge from …

Itw Deltar Model Factory, Bri Hollowell, Tyler Rogers, Jake Klingelsmith

Scholar Week 2016 - present

The project given to the design team was a request from ITW Deltar to improve their packaging system for some production machines in cell C. The primary goal of the project is to optimize the safety and workflow of the packaging systems in cell C. The safety of the packaging system will be determined using the REBA risk assessment number. The workflow improvement is determined through analysis of the packaging time and the walking distances of the workers.

The design team identified the functional requirements and design constraints that need to be met. These functional requirements include the packaging system …

Utilization And Standardization Of Beverage Based Containers, Michael T. Bobke, Jack C. Maughan, Kenia Vargas

Industrial and Manufacturing Engineering

The purpose of this document is to formally describe and explain all of the decisions associated with the data collection and analysis for this Cal Poly Senior Project. Throughout the project, we will utilize and hone the skills that each team member has developed during our time in Cal Poly's Engineering program. In addition, this document will briefly describe some of Blue Diamond’s history as one of the biggest almond companies in the world. The statement of work will introduce and describe the current status of the beverage base container process and international beverage container design. Next it will discuss …

Rebar Impalement Safety, Spencer C. Nefores, Steven M. Hoover

Industrial and Manufacturing Engineering

This project is sponsored by Webcor with the purpose of finding a better solution to rebar impalement safety. The current rebar impalement safety caps being used by Webcor were found to frequently fall off after being installed. This results in workers being exposed to the hazard for longer than desired. The research that has been done by the team showed that rebar impalement is a serious hazard and results in injury or death every year. Site visits and interviews were performed to aid in understanding the problem and designing solutions. The customer needs, current state of the problem, existing solutions, …

Parklets San Luis, Owen Kenny, Preston Jag Stebel, Leonidas Goodman, Lukas Braun

Industrial and Manufacturing Engineering

Downtown San Luis Obispo has been a popular destination for tourists, students, families, and roadtrippers. However, according to Ryan Betz, Interim Assistant to the City Manager, foot traffic and retail business revenue has been decreasing. Downtown SLO does not have enough free public spaces. Recent projects such as sidewalk bump outs and lighted crosswalks have aimed at making SLO more pedestrian accessible, but they have not actually made downtown more pleasurable. These projects have not seemed to drive any more business or traffic downtown. There are a myriad of ways to rectify this; studies show that having a free place …

Development And Experimental Investigation Of Modular Crates For Industrial Packaging Applications, Marshal Louie, Kumar B

Journal of Applied Packaging Research

For the increased product varieties, engineered plywood crate production technique could not facilitate box size optimization. This paper investigates the implementation of modularity function onto the plywood crate to resize the pack cube volume on customer requirement and to reduce space wastage inside the box. This is achieved by using a new joint technique called “Flat- Post Tongue Joint”. The full-sized experimental work is carried out comprising Flexural test analysis on Flat-Post Tongue joint, Tensile test analysis on tongue joint and Box Compression Test analysis on the two developed models of modular crates namely Modifiable Reinforced Plywood Crate (MRPC) and …

Dual-Axis Solar Tracker, Bryan Kennedy

All Undergraduate Projects

Renewable energies, and fuels that are not fossil fuel-based, are one of the prolific topics of debate in modern society. With climate change now becoming a primary focus for scientists and innovators of today, one of the areas for the largest amount of potential and growth is that of the capturing and utilization of Solar Energy. This method involves using a mechanical system to track the progression of the sun as it traverses the sky throughout the day. A dual-axis solar tracker such as the one designed and built for this project, can follow the sun both azimuthally and in …