Mechanical Engineering Commons^™

Elevated Temperature Progressive Damage And Failure Of Duplex Stainless Steel, Darren P. Luke

Civil Engineering ETDs

Ductile failure of metals has been the focus of research efforts within academia and industry for many years since it is tremendously important for understanding the failure of structures under extreme loading conditions. However, limited research has been dedicated to elevated temperature ductile failure, which is critical for evaluating catastrophic events such as industrial, structural or shipping vessel fires. A detailed investigation was conducted on the structural response of Duplex Stainless Steel at elevated temperatures. The temperature dependence of elastic modulus, yield strength, ultimate strength, and ductility was measured up to 1000°C and a continuum damage plasticity model was developed. …

Heat Of Fusion Of Primary Alcohol Confined In Nanopores, Harrisonn Griffin

Honors Theses

Melting behavior of physically confined 1-decanol in nano porous silica was probed using a Differential Scanning Calorimeter (DSC). In agreement with the Gibbs-Thomson prediction, we observe that the melting temperature of the confined 1-decanol scales inversely with the physical size of the pores. Contrary to the assumption used in developing the Gibbs-Thomson equation, however, the apparent heat of fusion decreases as the pore size decreases. Previously, several models have been proposed where interfacial layers of molecules do not participate in the phase transition and thereby would not contribute to the heat of fusion. While these could reconcile the seeming contradiction, …

Measurements Of Methyl Radicals And Temperatures By Using Coherent Microwave Rayleigh Scattering From Resonance Enhanced Multiphoton Ionization, Yue Wu

Doctoral Dissertations

This thesis includes two main parts: (I) The CH₃[methyl radical] detection in methane/air flames and (II) the rotational temperature measurement of O₂[molecular oxygen] in a variety of environments by using coherent microwave Rayleigh scattering from resonance enhanced multiphoton ionization (Radar REMPI).

In first the part, from Chapter I to Chapter III, the methyl radical detection and quantitative measurements have been conducted in hydrocarbon flame with one-dimensional and two-dimensional spatial-resolved concentration distribution. Due to the proximity of the argon resonance state (4+1 REMPI by 332.5 nm) with the CH₃ state (2+1 REMPI by 333.6 nm), in …

Prosthetic Thermal Management Device, Garrett Dowd

Williams Honors College, Honors Research Projects

High temperatures in lower-limb prosthetics can lead to poor user skin conditions and mechanical slippage between the user’s limb and the prosthetic. This report presents an air-cooling device for a lower-limb prosthesis. This device’s purpose is to maintain a constant skin-prosthesis interface temperature. A compact heat sink and small fan were used to transfer the bio-heat to the ambient surroundings. By changing the power of the fan, the thermal resistance of the whole system can be adjusted to match various thermal loads and environmental temperatures. Heat pads were used to mimic the heat generation of a residual limb, and cooling …

Formulation And Experimental Verification Of Alternate Calibration Techniques Of The Temperature Dependent Response Of Phosphor Fluorescence, Kelsey Michele Winstead

Masters Theses

The overall goal of this work is to provide an alternative approach to the thermographic phosphor (TP) time constant calibration method for temperature recovery. In this work two techniques are proposed that retain the pulsed source input used in the standard TP time constant calibration approach but reinterpret the phosphor response taken a fixed distance such that the single-exponential decay assumption is removed. The methods do not require knowledge of key parameters prior to data processing, nor do they involve complicated numerical schemes that attempt to fit data in the low signal-to-noise region of the phosphor response. The approaches do …

A Numerical Study Of High Temperature And High Velocity Gaseous Hydrogen Flow In A Cooling Channel Of A Ntr Core, Sajan B. Singh

University of New Orleans Theses and Dissertations

Two mathematical models (a one and a three-dimensional) were adopted to study, numerically, the thermal hydrodynamic behavior of flow inside a single cooling channel of a Nuclear Thermal Rocket (NTR) engine. The first model assumes the flow in the cooling channel to be one-dimensional, unsteady, compressible, turbulent, and subsonic. The working fluid (GH₂) is assumed to be compressible. The governing equations of the 1-D model are discretized using a second order accurate finite difference scheme. Also, a commercial CFD code is used to study the same problem. Numerical experiments, using both codes, simulated the flow and heat transfer …

Flame Temperature Imaging Of A Low Nox Burner Via Laser Rayleigh Scattering, Nicholas A. Smith

Master's Theses (2009 -)

Federal and global legislation are requiring increasingly stringent emission regulation on household appliances and in particular water heater burners. Emissions like NOx (NO and NO2) are a growing concern due to their adverse health effects and contribution to tropospheric ozone, acid rain, and smog formation. As NOx is more closely controlled, appliance manufacturers are developing low emission burners for use in water heaters.

Flame temperature is strongly correlated to NOx production. Hence, characterizing flame temperatures in new burners is a key part of improving upon burners used today and the development of future burners. Temperature measurements applied to a new, …

Barbeque Grill Temperature Distribution Design Improvement, Peter Gobell, Connor Mcgill, Thomas Willson

Mechanical Engineering

Team License to Grill set out to asses Bull Outdoor Products, Inc.’s barbeques and quantify the apparent uneven temperature distribution or “hot spots” and “cold spots” across the grill. This testing was accomplished with the design and fabrication of a test fixture allowing for accurate and repeatable temperature collection across the barbeque. With results that matched the sponsor’s claims of hot and cold spots, an engineering model was made using heat transfer and thermodynamic equations. Once the model somewhat resembled the experimental data, it was used to suggest different modifications that would allow for better temperature distribution. It was discovered …

Irrigation Leak Detection: Using Flow Rate Sensors To Detect Breaks In An Irrigation System, Adam Openshaw, Kalvin Vu

Computer Engineering

This report details the exploration and invention of a mechanism that can detect breaks in an irrigation system. With the ultimate goal of conserving water, we have designed an inexpensive, self sustaining flow rate monitor that can be used to identify anomalies in an irrigation system and wirelessly communicate the status of the system to a base station. Our implementation can also determine the direction of the anomaly based on the nature of the anomaly itself. This means that multiple monitors can be used to pinpoint the location of a break within the system in addition to merely detecting its …

Effects Of Liquid Transpiration Cooling On Heat Transfer To The Diverging Region Of A Porous-Walled Nozzle, Daniel J. Schieb

Theses and Dissertations

This research effort investigated the effects of evaporation of water on the heat transferred to the wall of the diverging portion of a porous walled nozzle The AFIT High Pressure Shock Tube was used with a two-dimensional Mach 3 nozzle. One flat surface of the nozzle was fitted with a layer of porous stainless steel from the nozzle throat to the exit. This porous material was saturated with water to simulate liquid transpiration cooling. Surface temperature data was taken in this region using fast response coaxial thermocouple. Heat transfer was determined from the surface temperature history. Data was taken for …