Materials Science and Engineering Commons^™

Photoelectrochemical Sensing Based On Zr-Mofs For Homocysteine Detection, Wen-Xia Dong, Guang-Ming Wen, Bin Liu, Zhong-Ping Li

Journal of Electrochemistry

Due to the independent form of the light source and detection system, photoelectrochemical (PEC) sensor has the advantages of low background, high sensitivity and simple operation. So far, PEC systems have been widely used in the fields including the actual detection of metal ions, biological antibodies or antigens in environmental pollutants. When the photosensitive material is irradiated by a light source with an energy being equal to or greater than its band gap, electrons (e^-) transition occurs from the valence band to the conduction band, leaving a hole (h⁺), at the same time, the generated electron-hole …

Temperature-Immune Self-Referencing Fabry–Pérot Cavity Sensors, Hengky Chandrahalim, Jonathan W. Smith

AFIT Patents

A passive microscopic Fabry-Pérot Interferometer (FPI) sensor an optical fiber a three-dimensional microscopic optical structure formed on a cleaved tip of an optical fighter that reflects a light signal back through the optical fiber. The reflected light is altered by refractive index changes in the three-dimensional structure that is subject to at least one of: (i) thermal radiation; and (ii) volatile organic compounds.

Radiation Effects On Lithium Indium Diselenide Semiconductors As Neutron Imaging Detectors, Robert M. Golduber

Masters Theses

The studies presented in this work aim to improve upon the knowledge base of lithium indium diselenide (LISe) semiconductors to understand how the material behaves in high radiation environments and refine the process of turning it into a neutron detector. LISe has great potential as neutron imaging detector because of the high neutron absorption efficiency of its enriched ⁶Li component and its ability to discriminate between gamma-rays and neutrons. Its ability to remain functional after being irradiated with large amounts of neutron fluence has been tested and the change in its electro-optical properties with relation to fluence has been …

Investigation And Characterization Of New Optically Stimulated Luminescence (Osl) Dosimetric Materials, Linyu Pan

All Dissertations

Optically stimulated luminescence (OSL) dosimeters have attracted increasing attention due to advantages over TL dosimeters, including no thermal quenching and higher sensitivity. Nevertheless, currently, there are only two commercially available OSL dosimeters, BeO and Al₂O₃:C. An OSL dosimeter requires low effective atomic number (Z_eff < 16), at least one type of recombination center and one type of trap, and UV~blue emission. In this dissertation, motivated by the search of new OSL dosimetric materials, a systematic investigation of alumina (Z_eff = 11.3) and magnesium aluminate spinel (Z_eff = 11.2) based materials was performed in terms of the engineering of the recombination centers and electronic traps. Microstructural characterization was executed by means of X-ray diffraction (XRD) and Raman spectroscopy. Luminescence was characterized under X-ray excitation (radioluminescence; RL) at ambient and …

Simulation And Fabrication Of All Oxide-Based Ito/Tio2/Cuo/Au Heterostructure For Solar Cell Applications, Sajal Islam

MSU Graduate Theses

Oxide heterostructures have drawn great attention lately, due to their environment-friendly properties and potential applications in optoelectronic devices. In this work, a simulation study of a heterojunction solar cell was performed with SCAPS (a solar cell simulator) using TiO2 as an n-type and CuO as a p-type layer. The thickness and the dopant-dependent simulations have shown that the solar cell operates at a maximum efficiency of 19.2% when the thickness of the TiO2/CuO layers is chosen 1.4µm/1.2µm compared to the 11.5% efficiency when FTO is replaced with ITO. An indium-doped tin oxide (ITO) vs fluorine-doped tin oxide (FTO) comparison study …

Pulsed Laser Annealing On The Optoelectronic Properties Of Zno Thin Films, Md Abu Zobair

MSU Graduate Theses

ZnO thin films have attracted great attention recently due to their unique electronic and optical properties. However, for proper implementation of ZnO in electronic devices it is necessary to understand the role of native point defects present inside the material as these wide bandgap semiconductors are inherently n-type due to oxygen vacancies. The objective is to control the electronic and optical properties of ZnO thin films through pulsed laser annealing (PLA). Thin films of ZnO have been grown on different substrates using pulsed laser deposition. Then PLA of the films are done by changing laser parameters (energy, frequency, pulse width, …

Investigation Of Optical And Structural Properties Of Gesn Heterostructures, Oluwatobi Gabriel Olorunsola

Graduate Theses and Dissertations

Silicon (Si)-based optoelectronics have gained traction due to its primed versatility at developing light-based technologies. Si, however, features indirect bandgap characteristics and suffers relegated optical properties compared to its III-V counterparts. III-Vs have also been hybridized to Si platforms but the resulting technologies are expensive and incompatible with standard complementary-metal-oxide-semiconductor processes. Germanium (Ge), on the other hand, have been engineered to behave like direct bandgap material through tensile strain interventions but are well short of attaining extensive wavelength coverage. To create a competitive material that evades these challenges, transitional amounts of Sn can be incorporated into Ge matrix to form …

Hybrid Two Dimensional Quantum Devices, Joshua Patrick Thompson

Graduate Theses and Dissertations

This thesis describes measurements on hybrid material systems involving two dimensional (2D) materials and phenomena along with the development of a small, hermetically sealed cell. The hermetic cell is designed to assist with analyzing sensitive 2D materials outside of an inert environment. When working with van der Waals materials that are especially sensitive to oxygen or water, it can be difficult to identify usable thin flakes without exposing them to air. To help preserve materials for analysis in air, a capsule was designed that isolates the material in an inert environment. Although the capsule is hermetically sealed, the encapsulated material …

Incorporation Of Zinc In Pre-Alloyed Cuin[Zn]S2/Zns Quantum Dots, Jean Carlos Morales Orocu

Graduate Theses and Dissertations

Since the early 2000s heavy-metal-free quantum dots (QDs) such as CuInS2/ZnS have attempted to replace CdSe, their heavy-metal-containing counterparts. CuInS2/ZnS is synthesized in a two-step process that involves the fabrication of CuInS2 (CIS) nanocrystals (NCs) followed by the addition of zinc precursors. Instead of the usual core/shell architecture often exhibited by binary QDs, coating CIS QDs results in alloyed and/or partially alloyed cation-exchange (CATEX) QDs. The effect that zinc has on the properties of CIS NCs was studied by incorporating zinc during the first step of the synthesis. Different In:Cu:Zn ratios were employed in this study, maintaining a constant 4:1 …

Two-Dimensional Black Phosphorus For Terahertz Emission And Near-Field Radiative Heat Transfer, Mahmudul Hasan Doha

Graduate Theses and Dissertations

The main focus of this work is to investigate two potential optical and optoelectronic applications of black phosphorus (BP): the near-field radiative heat transfer in plasmonic heterostructures with graphene and terahertz emission from multi-layer BP photoconductive antennas. When the separation distance between graphene-black phosphorene is much smaller than or comparable to the thermal wavelength at different temperatures, a near-field radiation heat transfer breaks the Planck blackbody limit. The magnitude of the near-field radiation enhancement acutely depends on the gate voltage, doping, and vacuum gap of the graphene and BP pair. The strong near-field radiation heat transfer enhancement of the specific …

Interferometric Lithography- An Approach To Large Area And Cost Effective Nanopatterning, Vineeth Sasidharan

Optical Science and Engineering ETDs

In this dissertation interferometric lithography is approached in two different ways to address two important constraints of nanopatterning. One approach solves the problem of scaling up interferometric lithography to wafer scale (4 inch or larger) area. Through the second approach we have developed a nanopatterning technique based on interferometric lithography by using an inexpensive (~$100) diode laser as source, making interferometric lithography a very cost-effective technique.

Wafer-scale large-area nanopatterning was developed using an amplitude grating mask as a grating beam splitter along with spatial averaging of laser intensity by wobbling. The longitudinal and transverse coherence issues both are eased by …

Optically Active Selenium Vacancies In Baga4Se7 Crystals, Brian C. Holloway [*], Timothy D. Gustafson, Christopher A. Lenyk, Nancy C. Giles, Kevin T. Zawilski, Peter G. Schunemann, Kent L. Averett, Larry E. Halliburton

Faculty Publications

Barium gallium selenide (BaGa₄Se₇) is a recently developed nonlinear optical material with a transmission window extending from 470 nm to 17 μm. A primary application of these crystals is the production of tunable mid-infrared laser beams via optical parametric oscillation. Unintentional point defects, such as selenium vacancies, cation vacancies (barium and/or gallium), and trace amounts of transition-metal ions, are present in BaGa₄Se₇ crystals and may adversely affect device performance. Electron paramagnetic resonance (EPR) and optical absorption are used to identify and characterize these defects. Five distinct EPR spectra, each representing an electron …

Method Of Making Temperature-Immune Self-Referencing Fabry–Pérot Cavity Sensors, Hengky Chandrahalim, Jonathan W. Smith

AFIT Patents

A method of making passive microscopic Fabry-Pérot Interferometer (FPI) sensor includes forming a three-dimensional microscopic optical structure on a cleaved tip of an optical fiber that reflects a light signal back through the optical fiber. The reflected light is altered by refractive index changes in the three-dimensional structure that is subject to at least one of: (i) thermal radiation; and (ii) volatile organic compounds.

Perovskite Film Formation For Solar Cell Absorbers: Effects Of Substrate Modification, Mirra M. Rasmussen, Kyle M. Crowley, Ina T. Martin

Student Scholarship

As perovskite solar cell efficiencies have risen rapidly, practical constraints have made durability a critical concern. Whereas much attention has been paid to the development of the perovskite absorber layer, the charge transport layers can also be engineered to better the performance and stability of the device. This work uses the molecular modifier bromopropyltrimethoxysilane (BPTMS) to alter the interface between indium tin oxide (ITO, a common thin film solar cell transparent electrode) and methylammonium lead iodide (MAPbI3, a common perovskite absorber) to improve the morphology and stability of the perovskite absorber film. The substrate, molecular modifier, and perovskite film were …

Engineering The Surface Of Fe3o4 Nanoparticles For Catalytic And Magnetic Applications, Natalia Da Silva Moura

LSU Doctoral Dissertations

With the rapid depletion of the U.S. energy resources coupled with population growth, heat management technologies must be improved to sustain our quality of life. Precisely, in catalysis, it is estimated that only ~50% of the energy supplied to the reactor is used for product conversion due to dissipation losses. Among the emerging technologies with a promising reduction in heat losses is induction heating, offering targeted heat delivery with magnetic nanoparticles. Under alternating magnetic fields (AMF), these nanoparticles can absorb the energy from Radio-Frequency (RF) fields and dissipate it as heat on the nanoparticle surface. This in situ heat generation …

Helical Dielectric Elastomer Actuator, Daewon Kim

Publications

A helical dielectric elastomer actuator (HDEA) can include a first dielectric region comprising an elastomer defining a helix. In an example, a dielectric material can be deposited, and a compliant conductive material can be deposited, such as using an additive manufacturing approach, to provide an HDEA. In an example where the HDEA has multiple mechanical degrees of freedom, at least two compliant conductive regions can be located on a first surface of the first dielectric region and at least one compliant conductive region can be located on an opposite second surface of the first dielectric region. For such an example, …

High Resolution Electron Energy Loss Spectroscopy Of Plasmonic Nanostructures, Grace Pakeltis

Doctoral Dissertations

This dissertation discusses developing fabrication techniques to study the plasmonic phenomena of nanostructures utilizing high spatial and energy resolution of monochromated aberration-corrected scanning transmission electron. While standard lithography has been widely used to create planar nanostructures, investigation into 3-dimensional nanostructures is lacking. A robust synthesis approach utilizing focused electron beam induced deposition, atomic layer deposition, and thin film sputter deposition to fabricate complex 3D plasmonic architectures is described and characterization of single nanoresonators is presented. Additionally, this dissertation discusses the use of high-resolution electron energy loss spectroscopy to investigate the hybridization of gold nanorod oligomers. Experiment and simulation resolve magnetic …

Rapid Annealing Of Perovskite Solar Cell Thin Film Materials Through Intense Pulse Light., Amir Hossein Ghahremani

Electronic Theses and Dissertations

Perovskite solar cells (PSCs) have garnered a great attention due to their rapid efficiency improvement using cheap and solution processable materials that can be adapted for scalable high-speed automated manufacturing. Thin film perovskite photovoltaics (PVs) are typically fabricated in an inert environment, such as nitrogen glovebox, through a set of deposition and annealing steps, each playing a significant role on the power conversion efficiency (PCE), reproducibility, and stability of devices. However, atmospheric processing of PSCs would achieve lucrative commercialization. Therefore, it is necessary to utilize materials and methods that enable successful fabrication of efficient PSCs in the ambient environment. The …

Surface Energy And Microstructure: The Effect Of The Underlying Substrate On Perovskite Film Formation For Solar Cell Absorbers, Mirra M. Rasmussen, Kyle M. Crowley, Ina T. Martin

Student Scholarship

No abstract provided.

Decoupling The Effects Of Interfacial Chemistry And Grain Size In Perovskite Stability, Mirra M. Rasmussen, Kyle M. Crowley, Miranda S. Gottlieb, Geneviève Sauvé, Ina T. Martin

Student Scholarship

No abstract provided.

Fabrication And Characterization Of Photodetector Devices Based On Nanostructured Materials: Graphene And Colloidal Nanocrystals, Wafaa Gebril

Graduate Theses and Dissertations

Photodetectors are devices that capture light signals and convert them into electrical signals. High performance photodetectors are in demand in a variety of applications, such as optical communication, security, and environmental monitoring. Among many appealing nanomaterials for novel photodetection devices, graphene and semiconductor colloidal nanocrystals are promising candidates because of their desirable and unique properties compared to conventional materials.

Photodetector devices based on different types of nanostructured materials including graphene and colloidal nanocrystals were investigated. First, graphene layers were mechanically exfoliated and characterized for device fabrication. Self-powered few layers graphene phototransistors were studied. At zero drain voltage bias and room …

Distributed Modeling Approach For Electrical And Thermal Analysis Of High-Frequency Transistors, Amirreza Ghadimi Avval

Graduate Theses and Dissertations

The research conducted in this dissertation is focused on developing modeling approaches for analyzing high-frequency transistors and present solutions for optimizing the device output power and gain. First, a literature review of different transistor types utilized in high-frequency regions is conducted and gallium nitride high electron mobility transistor is identified as the promising device for these bands. Different structural configurations and operating modes of these transistors are explained, and their applications are discussed. Equivalent circuit models and physics-based models are also introduced and their limitations for analyzing the small-signal and large-signal behavior of these devices are explained. Next, a model …

Direct Torque Control For Silicon Carbide Motor Drives, Mohammad Hazzaz Mahmud

Graduate Theses and Dissertations

Direct torque control (DTC) is an extensively used control method for motor drives due to its unique advantages, e.g., the fast dynamic response and the robustness against motor parameters variations, uncertainties, and external disturbances. Using higher switching frequency is generally required by DTC to reduce the torque ripples and decrease stator current total harmonic distortion (THD), which however can lower the drive efficiency. Through the use of the emerging silicon carbide (SiC) devices, which have lower switching losses compared to their silicon counterparts, it is feasible to achieve high efficiency and low torque ripple simultaneously for DTC drives.

To overcome …

Numerical Calculation Of Losses Of Trapped Vortices Under Strong Rf Meissner Current And Dc Superheating Field In Type Ii Superconductors, Walive Pathiranage Manula Randhika Pathirana

Physics Theses & Dissertations

Research on the vortex dynamics and enhancing of superheating field in superconductors has attracted much attention in accelerator physics community to develop next-generation high-performance accelerator cavities. However, the extreme dynamics of curvilinear elastic vortices driven by very strong currents close to the depairing limit or superheating field of a superconductor with a nanostructured surface has not been well understood. We calculated the superheating field H_sh and critical momentum kc characterizing the wavelength of the instability λ_m of the Meissner state to flux penetration by solving numerically the Ginzburg-Landau equations. A bulk superconductor, superconductor with the inhomogeneous surface disorder …

Research And Application Of Copper Electroplating In Interconnection Of Printed Circuit Board, Chong Wang, Chuan Peng, Jing Xiang, Yuan-Ming Chen, Wei He, Xin-Hong Su, Yu-Yao Luo

Journal of Electrochemistry

Copper electroplating is the key technology for manufacturing of integrated circuit, packaging substrate, printed circuit board, and other electronic interconnection components. However, the electrochemistry and mechanism of deposition growth have not been fully elucidated, and the development of additives and bath maintenance are inseparable from a large number of experiments. This article reviews recent fundamental research and application progress in copper electroplating for printed circuit board industry, and these works are mainly dedicated by the research group of Printed Circuit and Printed Electronics from University of Electronic Science and Technology of China. First of all, a brief history of copper …

Design And Fabrication Of Zinc Oxide Optofluidic Laser Elements, Kyle T. Bodily

Theses and Dissertations

This thesis systematically goes through the derivation, simulation, and experimentation of Zinc Oxide optofluidic micro laser elements. Single and coupled ring resonators were simulated to show single mode transmission as well as enhanced coupling capabilities when surrounded by high refractive index liquid. Devices with diameters ranging from 100-500 µm were successfully fabricated inexpensively through standard cleanroom procedures. The devices were tested using two different pump laser systems. Testing included such factors as high pump intensity, various angles of excitation, and low temperature. In all cases PL emission was observed and recorded.

Experimental Investigation Of Surface Resistivity Of Yttrium Stabilized Zirconium As A Thin Film, Matthew J. Melfi

Seton Hall University Dissertations and Theses (ETDs)

Solid Oxide Fuel Cells are devices that use electrochemical reactions to convert chemical energy from fuel to electricity. In comparison with coal power plants, a Solid Oxide Fuel Cell, produces a higher electrical conversion efficiency. However, at higher temperatures (1000°C) it creates a lower ionic conductivity, which limit the Solid Oxide Fuel Cells. When lowering the temperature, the ohmic resistance increases. In our research, an Yttrium Stabilized Zirconium layer will be produced from a fine dimple grain structure allowing high flow of oxygen mobility. This mobility increases ionic conductivity and decrease ohmic loss. The goal of our research is first …

Performance And Economics Of Solar Inverters And Module Level Power Electronics In A 1 Mw Photovoltaic System, Maxwell Criswell

Biological and Agricultural Engineering Undergraduate Honors Theses

Photovoltaic solar panels convert sunlight to electricity in the form of direct current; therefore, a necessary component of every photovoltaic system is an inverter to convert the electricity to usable alternating current. There are various commercially available inverter technologies manufactured today such as microinverters, string inverters, and central inverters, as well as module level power electronic devices such as DC optimizers that are capable of improving system performance in string and central inverter systems. This thesis compares the performance and economics of five different inverter and module level power electronic systems through model simulation using Helioscope software. The five alternatives …

Manipulation Of Excited States In Organic-Inorganic Hybrid Perovskite Optoelectronic Devices, Jia Zhang

Doctoral Dissertations

In recent years, a huge success on photovoltaic and light emitting has been achieved in the field of organic-inorganic hybrid perovskites owing to the superior optoelectronic properties of excited states. Regulating the primary excited states is the foundation of developing multi-functional optoelectronics, including the light-emitting, photovoltaic and lasing actions. By revisiting the photophysical processes of excited states, some new strategies are suggested to further pushing the efficiency of perovskites forward. This thesis focuses on the manipulation of excited states through combining optoelectronic devices, from excited states generation to excited charge carrier transport.

Chapter 1 presents a basic introduction to excited …

Spin Effects Of Excited States In Organic Semiconductors And Hybrid Perovskites For Optoelectronics And Spintronics, Miaosheng Wang

Doctoral Dissertations

Organic semiconductors and organic-inorganic hybrid perovskites have demonstrated versatile functionalities for optoelectronic and spintronic applications. Research in this dissertation focuses on the spin effects of excited states in emerging organic semiconductor and hybrid perovskite systems to understand the fundamental working principle. The investigation on the spin effects in excited states can provide insightful guidance for the development of the next-generation organic and hybrid perovskite optoelectronics and spintronics.

In organic semiconductors, the excited states, namely, excitons can be characterized by the total spin angular momentum S=S_e+S_h of the constituent electron and hole, which determines the …